Ltf21 Parts

Secures hoses to pumps, tubs, and valves preventing leaks. Replace if worn, loose, or causing drips during cycles. Confirm fit with your model number.

Washer drum baffle mounts inside the tub to lift and tumble laundry. Replace if cracked, broken, or missing to prevent snags and restore quiet operation.

Shipping bolt kit secures washer tub and suspension during transport. Install before moving to prevent internal damage, then remove before use.

This is an electrically controlled water inlet valve that regulates the flow of hot and cold water into the washing machine tub during fill cycles. It opens and closes in response to signals from the control board to deliver the correct water temperature and volume. Replace this valve if the washer is not filling with water, filling slowly, leaking from the back, or continuing to fill when it should stop.

This replacement screw secures appliance panels and components. With a #10-16 thread and 0.75-inch length, it replaces stripped, rusted, or missing hardware to restore a tight, rattle-free fit and reduce vibration and noise.

• Fastens cabinet panels, brackets, or internal parts in washers and dryers
• Direct replacement for worn or lost screws to keep assemblies aligned and secure
• Helps address loose/vibrating panels, rattling noises, or visible gaps/misalignment
• Spec: #10-16 thread; 0.75-inch length

• Disconnect power; for washers, also shut off water supply
• Match the original screw location; start threads by hand to prevent cross-threading
• Use a driver that fits the screw head properly; tighten snugly without overtightening

This is the lower access panel, also called a toe panel, that attaches to the front bottom of the washer. It covers the internal components beneath the drum area and provides a finished appearance. Replace this panel if it is dented, cracked, rusted, or if the mounting tabs are broken, leaving the lower portion of the machine exposed.

Machine screw secures panels, brackets, and internal components in washers. Replace missing, rusted, or stripped screws to restore proper fit and alignment.

Screw: 8-16 x 3/8 inch.

Silicone lubricant conditions rubber seals and O-rings in appliances. Apply during service to ease installation and prevent leaks. Confirm fit by model.

Replacement mounting screw for washers and laundry centers. Secures components like pulleys, brackets, and panels. Replace if missing, stripped, or damaged.

Replacement mounting screw secures panels, brackets, and trim to the appliance frame. Needed when original screw is stripped, missing, or damaged.

Refrigerator won't cool or compressor rattles? This sealed system compressor restores cooling. Professional installation required for refrigerant work.

This thermostat retainer clip secures the defrost thermostat to the evaporator tubing in your refrigerator or freezer, maintaining firm contact for accurate temperature sensing and dependable defrost operation.

• Holds the thermostat firmly against the evaporator line for proper temperature feedback
• Helps prevent a loose or dangling thermostat that contribute to frost buildup and poor defrost performance
• Restores correct mounting when the original clip is cracked, bent, or missing
• Common signs include a broken clip or a thermostat not attached to the coil

• Disconnect power to the appliance before servicing; wear cut-resistant gloves
• Access the evaporator compartment; remove accumulated frost/ice as needed without prying on coil fins
• Position the thermostat body flat against the tubing and snap the retainer over it, avoiding pinched wires or damaged fins
• Confirm a secure fit and proper wire routing before reassembling and restoring power

This is a metal hinge that attaches the dryer door to the cabinet and allows it to swing open and closed. It supports the weight of the door and ensures proper alignment with the door latch. Replace this hinge if the dryer door is sagging, not closing properly, or if the hinge is cracked, bent, or has worn-out pin holes.

The Cord is an OEM replacement part for Frigidaire washing machines. Extending from the rear of the unit, it safely powers the washer through a connection to a wall outlet.

Causes of cord failure are normal wear from frequent coiling and plugging/unplugging motions over the appliance's lifespan. Rodents or sharp edges may also damage the outer jacketing.

Signs of a bad cord include:

• Exposed or severed copper wiring visible inside
• External cracks, splits or abrasions eroding the casing  
• Erratic behavior during the wash cycle
• GFCI/EGCI outlet tripping frequently

Compatible models also include Electrolux, KitchenAid, Jenn-Air, and Kenmore options. Maintaining safety is a top priority.

This is the complete detergent dispenser drawer assembly for a front-load or top-load washing machine. It holds and dispenses detergent, fabric softener, and bleach at the appropriate times during the wash cycle. Replace this assembly if the dispenser drawer is cracked, if detergent is not dispensing properly, or if residue builds up and cannot be cleaned out.