Mav7800aww Parts

My husband is a natural handyman, I call him Bob the Builder (don't tell him I told you that!). When our washer started leaking we started looking for a used one online, when that didn't work he figured he'd take it apart and see if he could find the problem himself. Well after doing some research online we replaced the drain pump, which in the long run was a good idea because ours wasn't in very good condition, but our washer still leaked. So after some more looking around he found a hole on... Read more

I replaced the entire agitator (my appliance agitator could only be replaced in one part not the upper part only). It was super easy but one thing....the video on the website was not helpful because my maytag washer is older and does NOT have a screw down inside the agitator but has one 1/4 inch hex nut on the side down by the base. Good for me though because all I had to do was unscrew the nut, put the new agitator on, tighten the new nut and DONE!! Read more

I replaced the switch, the plunger, plunger guide and the lid cam, but the cam still didn't turn on the switch. Turned out someone had stood on the washer and bent the lid slightly, not enough to notice, but since I had ruled out just about everything else I started looking at the lid itself. I ended up bending it back close to it's original shape and now it works fine. I guess I learned a few things about washing machines though. One lesson is when you pull off the controls, the hose leading... Read more

I had removed three screws behind the control board cover of the washer, to access the old lid switch. I checked the continuety of the of the switch with a multimeter and it obviously failed the the test by displaying infinity of <1, rather than being 0. I removed the old switch with a flathead screw driver, I tested the new one and installed it in no time. Problem solved!!! Read more

Replaced flow meter and control valve Read more

I put all pieces that I ordered on the dryer and plugged it in. Read more

By watching your video and following the instructions Read more

Watched the video and in 5 mins I was all done, very easy. Read more

I replaced the switch, the plunger, plunger guide and the lid cam, but the cam still didn't turn on the switch. Turned out someone had stood on the washer and bent the lid slightly, not enough to notice, but since I had ruled out just about everything else I started looking at the lid itself. I ended up bending it back close to it's original shape and now it works fine. I guess I learned a few things about washing machines though. One lesson is when you pull off the controls, the hose leading... Read more

Watched the video and in 5 mins I was all done, very easy. Read more

I replaced the switch, the plunger, plunger guide and the lid cam, but the cam still didn't turn on the switch. Turned out someone had stood on the washer and bent the lid slightly, not enough to notice, but since I had ruled out just about everything else I started looking at the lid itself. I ended up bending it back close to it's original shape and now it works fine. I guess I learned a few things about washing machines though. One lesson is when you pull off the controls, the hose leading... Read more

Model# MAV7257AWW Maytag Atlantis Washing Machine. Repairs were fairly easy along with the videos appliancepartspros offers on their website. Parts also came with instructions on how to install. Other videos were available on You Tube. The only part difficult to install was Thrust bearing kit - make sure when installing to pull down on shaft so washer and e-clip will fit. Another note, you can get a pulley for your replacement motor pulley on eBay and Maytag.com. Just pay close attention to... Read more

Replaced coils on gas valve; while at it replaced door screws which were starting to wear from assorted repairs over the years. Read more

I followed the Appliance Parts Pro's advice videos for the Maytag MAV6451AWW Atlantis washer on replacing the snubber ring and the suspension springs. Everything went just fine except replacing the two rear most suspension springs. None of the videos illustrated REINSTALLING the REAR springs which is extremely difficult because you can't get enough leverage with your arm extended. Observing my frustration, my wife recommended taking off the back side. You can't simply take off the back,... Read more

Replaced lid safety switch, actuator and plunger. Read more