Mav7800aww Parts

This surface burner valve controls gas flow to a cooktop or range burner for smooth ignition and precise flame adjustment. Replacing a worn valve restores reliable lighting and consistent simmer-to-high control at the knob. What it does:

• Regulates and meters gas flow to a surface burner from Off through all heat settings
• Wear or blockage can cause no ignition, hard-to-turn knob, or poor/unstable flame
• Helps correct burners that won't adjust properly or won't stay lit
• Ensures safer, consistent burner performance when operating correctly

• 1 surface burner valve

• Disconnect power and shut off gas supply before servicing; allow appliance to cool
• Work in a well-ventilated area and follow local codes
• Note knob orientation; transfer any orifice fittings or mounting hardware from the old valve
• After installation, check all connections for leaks using a non-corrosive leak-detection solution

Color: White.

This replacement screw secures appliance panels and components. Use this OEM fastener to swap out stripped, corroded, or missing hardware so assemblies stay tight, aligned, and quiet for reliable day-to-day operation.

• Provides secure attachment for panels, brackets, and internal assemblies
• Direct replacement for stripped, corroded, or lost screws
• Can help with symptoms like vibration, rattling, or loose/misaligned parts
• Supports proper fit to reduce gaps or unwanted movement

• Disconnect power; for gas or water appliances, shut off the supply before service
• Note hardware order and retain any spacers or clips from the original setup
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Repair or replace the mating part before installation

To order indicator lens use WP22001948.

This suspension spring hook connects a tub suspension spring to the washer frame, helping support and center the wash basket. Replacing a worn or missing hook can reduce shaking, banging, and off-balance interruptions during spin.

• Secures one end of a suspension spring to the cabinet/base
• Helps control tub movement and absorb vibration during agitation and spin
• Failure signs include excessive vibration or banging, tub leaning/sagging, or frequent out-of-balance stops

• Disconnect power and water; wear gloves and eye protection
• Access the suspension area per model; support the tub to relieve spring tension
• Use pliers or a spring tool to remove the old hook; note orientation and mounting location
• Seat the new hook fully and ensure the spring is engaged securely before reassembly and testing

Hose washer and plastic insert for inlet hose. To order separately: for washer use WPY013783, for strainer use WP22002960.

This small retaining clip secures components in place inside the appliance, helping prevent movement, vibration, and premature wear. Replace a bent, fatigued, or missing clip to restore a solid, factory-tight hold.

• Holds panels, brackets, or tubing securely in their mounts
• Helps maintain alignment to reduce rattles, rubbing, or intermittent issues
• Common signs of failure: missing clip, loose fit, buzzing/vibration, parts that won't stay seated
• Restores proper retention after service, transport, or vibration-related fatigue

• Disconnect power and shut off gas/water before servicing
• Note the original clip's orientation; remove with needle-nose pliers
• Seat the new clip fully—do not over-bend; spring tension provides the hold
• Test operation before reassembly

This 240V lid switch senses when the washer lid is closed so the cycle can run and spin safely. Replacing a failed switch restores reliable lid detection and prevents unexpected cycle interruptions due to a false "lid open" condition.

• Detects a closed lid to enable motor and spin functions
• Opens the circuit when the lid is raised for safety
• Failure symptoms: won't start, won't spin or agitate, or stops mid-cycle as if the lid is open

• Unplug the washer before servicing
• Confirm your model specifies the 240V lid switch; access it by lifting the top or removing the control console/top, depending on model design
• Transfer wiring and mounting exactly; route harness clear of moving parts and ensure the lid actuator fully engages the switch
• After reassembly, test start and spin with the lid closed; never bypass the safety interlock

This retaining ring secures a component on a shaft or within a groove so it stays aligned during operation. Replacing a bent, rusted, or missing ring helps stop wobble, noise, and parts working loose.

• Locks into a groove to keep gears, pulleys, wheels, or spacers from sliding off a shaft
• Helps maintain proper spacing and alignment of moving parts
• Common signs of failure: wobbling parts, scraping/rubbing noises, or components that work loose
• Visual clues: deformation, corrosion, or loss of spring tension

• Disconnect power and any utilities to the appliance before service
• Wear eye protection—retaining rings can spring free under tension
• Note the order/orientation of any washers or spacers before removal
• Use appropriate snap-ring or needle-nose pliers and ensure the ring seats fully in its groove

Color: chrome. The main part of the knob is about 1 inch in diameter. The handle is about 2 inches.

This washer tub mounting bolt secures the tub assembly to its support points. Replacing worn or missing hardware helps keep the tub aligned and stable through wash and spin, reducing vibration and noise. What it does:

• Anchors the tub assembly to its mounting bracket or frame
• Helps maintain alignment under load and during high-speed spin
• Replace if the bolt is stripped, rounded, rusted, or missing
• Symptoms can include excessive vibration/banging, tub shifting or scraping, and rattling hardware

• 1 mounting bolt

• Disconnect power and water before servicing; wear appropriate PPE
• Support the tub to relieve stress on the mounting points before removal
• Start threads by hand to avoid cross-threading; tighten bolts evenly across all mount points
• Do not overtighten; follow for torque guidance

Screw: 8-16 x 3/8 inch.

Drive motor isolator.

Specs: No.8X1/2 HEX WASHER HEAD

Size: 10-24 x 3/8 inch.

Motor plate isolator.