Maytag A500 Parts

The Leveling Leg Pad is an OEM replacement part for Whirlpool washing machines. This small but essential component fits beneath the leveling legs, providing stability and preventing the appliance from moving or vibrating excessively during operation. It also protects flooring surfaces from potential scratches or damage.

Symptoms of a bad Leveling Leg Pad include:

• Increased vibration or noise during the wash or spin cycle
• The washing machine wobbling or becoming unsteady
• Visible wear, cracks, or damage to the pad

Causes of a failing Leveling Leg Pad can include wear and tear from prolonged use, exposure to moisture, or excessive weight causing deformation. Replacing worn pads helps maintain the appliance's balance and efficiency.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

For the leveling leg order 22003428.

This adapter tube assembly connects sections of the appliance's water line to create a secure, leak-resistant path for water flow. Replace it if the tube is cracked or the connection no longer seals properly to prevent leaks and restore flow.

• Connects water tubing between components within the appliance's water system
• Helps maintain a tight, leak-resistant seal at the joint
• Restores proper water flow when a tube or connector is damaged
• Typical symptoms: water leaking at the connection, reduced or no water flow, visible cracks/kinks, loose fit

• Disconnect power and shut off the water supply before servicing
• Relieve line pressure and place a towel or pan to catch any residual water
• Note routing and orientation before removal to ensure correct reassembly
• After installation, restore water and check all connections for leaks

Leg, adjustable (w/nut)

This replacement seal restores a tight, leak-resistant barrier between mating parts inside your appliance. Replacing a hardened or damaged seal helps stop seepage and keeps the system operating as designed. What it does:

• Forms a tight barrier between components to contain fluids and prevent leaks
• Helps maintain proper pressure/flow at the sealed joint
• Reduces risk of moisture damage around the connection point
• Common signs it's worn: drips or puddles, dampness around the joint, musty odors, visible cracking or flattening of the old seal

• 1 seal

• Disconnect power and shut off water or gas supplies before servicing
• Access the sealed joint; remove the old seal and clean mating surfaces thoroughly
• Lightly lubricate with manufacturer-approved lubricant; install without twisting
• Reassemble, restore utilities, and check closely for leaks during initial operation

For complete assembly order WP206680.

Size: 90 inches long. To order hose extension use 12001585. To order siphon break use 76660.

This replacement screw secures panels, brackets, and components inside appliances. Replacing a missing or stripped fastener restores a snug, rattle-free fit using the correct #8-18 thread and 5/8-inch length.

• Fastens covers, trims, brackets, and internal parts to the cabinet/frame
• Used wherever a #8-18 x 5/8 screw is specified
• Replace if the original is missing, corroded, stripped, or will not tighten
• Symptoms: loose or rattling panels, gaps, or hardware that backs out

• Disconnect power; shut off gas/water before servicing
• Match thread and length; start by hand to avoid cross-threading
• Use the correct driver bit and tighten snugly—do not overtighten
• Inspect and replace damaged clips or tabs before securing

This hose clamp secures a hose connection to prevent leaks and keep your appliance running smoothly. It provides a tight, reliable hold on the hose fitting so water or air stays contained during operation.

• Tightens around a hose and fitting to maintain a secure seal
• Helps stop drips, seepage, or loose connections
• Common fix when you see moisture around a hose joint
• Useful if a clamp is rusted, stretched, or no longer holding tension

• Unplug power and shut off water (if applicable) before servicing
• Note clamp position/orientation before removal
• Use appropriate screwdriver or nut driver to tighten evenly
• Do not overtighten—ensure a snug, leak-free seal without damaging the hose

This internal hose connects the washer's outer tub to the drain pump, channeling wash water during the drain cycle. Replacing a worn or leaking hose helps prevent puddles and supports reliable draining performance.

• Routes water from the outer tub to the drain pump inside the washer
• Maintains a sealed path; cracks or loose connections can lead to leaks
• Visible splits, soft spots, swelling, or aging can cause water under the unit
• Obstructions or internal collapse may contribute to slow or incomplete draining

• Disconnect power and turn off water supply before servicing
• Expect residual water; use towels or a pan when removing the old hose
• Note hose routing and clamp positions; seat fully on each port and secure with appropriate clamps
• Run a quick fill/drain test and check all connections for leaks after installation

This agitator seal assembly sits at the agitator/drive-shaft pass-through to keep wash water inside the tub and away from the drive system. Replacing a worn seal helps stop center-post leaks and protects internal components from moisture.

• Seals the opening where the agitator/drive shaft passes through the tub or centerpost
• Helps prevent water from migrating into the centerpost/gearcase area
• Supports reliable agitation and spin by keeping contaminants out of the drive assembly
• Common symptoms of failure: water leaking from the center of the tub or beneath the washer, or rust/water tracks around the agitator hub

• Disconnect power and shut off water; wear gloves and eye protection
• Remove agitator cap and fastener, then lift the agitator to access the seal (procedure varies by model)
• Note the original seal orientation; clean mating surfaces and install the new seal squarely (lightly lubricate only if specified by the manufacturer)
• Reassemble and run a short fill/agitate test while observing for leaks

This hose clamp secures a rubber or plastic hose to its fitting to maintain a tight, leak-resistant seal. Replace a worn or missing clamp to stop drips and keep appliance water connections secure.

• Fastens a hose to a barb or port to prevent leaks
• Helps keep hoses from slipping off due to vibration or pressure
• Restores proper sealing when a clamp is rusted, bent, or stripped
• Common symptoms: water dripping at a hose joint, loose hose connection, or a clamp that won't tighten

• Disconnect power and shut off the water supply before servicing
• Place a towel to catch residual water when removing hoses
• Position the clamp just behind the hose barb/bead and secure with the appropriate tool
• Restore water and power, then run a quick check for leaks at the connection

For complete assembly order WP206680.

This hose clamp secures a flexible hose to its fitting to help prevent leaks and hose blow-offs during operation. Replace a rusted, stripped, or distorted clamp to restore a tight, reliable seal at the connection point.

• Applies clamping force around a hose to hold it on a barb or stub fitting
• Commonly used on washer drain and tub-to-pump hose connections
• Helps stop drips at the joint and prevents the hose from slipping off
• Typical failure signs: leaking at the connection, clamp won't tighten, visible rust, broken/warped band

• Unplug the appliance and turn off water supply; expect some residual water
• Seat the hose fully on the fitting; place the clamp just behind the bead/barb
• Tighten until snug and secure; do not overtighten to avoid damaging the hose
• Run a short test cycle and recheck for leaks at the connection

This bolt is a genuine Whirlpool part, sold individually. It can be used as a replacement part for a washing machine or a washer/dryer combination appliance. This bolt fastens parts to one another in conjunction with a nut so that they do not come loose while the washing machine vibrates when it is in operation.A bolt might be easily lost or misplaced as it is a small part that might go missing without any noticeable symptoms. Additionally, a bolt might be stripped through general wear and tear or as a result of a direct impact collision with a hard object that warps the component beyond functionality. If any of these things occur, the bolt should be replaced by this genuine OEM replacement part.This is an OEM part sourced directly from the manufacturer. It is sold individually. This bolt is compatible with the following appliance brands: Whirlpool, Maytag, International, and Jenn Air.

This lid bumper cushions the contact point between a washer lid and the top panel to reduce slamming noise and protect the finish. Replacing a worn or missing bumper restores smooth, quiet lid operation and helps prevent paint damage.

• Provides a soft stop between the lid and top to minimize noise and vibration
• Helps prevent chips, scratches, and rust where the lid meets the cabinet
• Maintains proper lid spacing for a solid, rattle-free close
• Common signs it's needed: missing/flattened bumper, louder closing, rattling, or visible wear at contact points

• Disconnect power before servicing
• Open the lid, remove the old bumper, and clean the mounting area
• Seat the new bumper fully in the mounting location as designed
• Open/close the lid to ensure quiet, secure contact

This injector seal fits the refrigerator's water injector. It restores a tight, watertight/airtight connection where the injector passes through the liner or mates to the fill tube, helping prevent leaks and frost around the opening.

• Seals the injector-to-liner/fill-tube connection to stop water seepage and air leaks
• Helps prevent frost/ice buildup near the injector area and fill tube freeze-ups
• Addresses issues from a cracked, shrunken, or missing seal
• Common symptoms: water drips at the back/freezer wall and frost near the fill opening

• Disconnect power and shut off the water supply before servicing
• Access the injector area (rear of freezer or cabinet, depending on model)
• Remove the old seal; press the new seal fully and evenly into place
• Reassemble, restore water/power, and check for leaks and proper fill