We use cookies and similar tools for site analytics and advertising. By using our site, you agree to this. See our Privacy Policy for details. Do Not Sell or Share My Personal Information
Need Help?
Call
Washer won't spin, makes buzzing noise, or smells like burning? Replace the drive motor. Watch our video for step-by-step help. Average repair time: 1 hour.
I ordered a new motor with a very helpful Chris.It arrived a day later with instructions and was easy to exchange with the old one.I am delighted with how it works and the price was good and the service excellent.thank you. Read more
Usually ships within 4 - 14 days
Prevents backflow of drain water into fresh water supply. Mounts on top of washer. Replace if cracked, leaking, or damaged to restore proper drainage.
We ordered parts from appliance parts pros and I fixed it. Read more
Washer won't spin or spins slowly? This motor mount roller and spring kit restores proper spin performance. Moderately easy DIY repair with video guide.
The washer was on, and I heard a faint humming sound in the laundry room. I went in and opened the washer and it was full of soapy water in the middle of its cycle and was not agitating. I also smelled a faint burning smell. At this point I figured the problem was a bad motor, as the washer is more than 20 years old. I have fixed it twice before, because the first time, the repairman said I should keep this washer going as long as possible. It was made to last with a metal drum, unlike newer... Read more
Prevents oil leaks from the transmission area. Replace if you see oil puddles under your washer. Confirm fit with your model number before ordering.
I had a lot of problems removing the spin hub, I had to use an air impact wrench to un screw it even then it was very hard, it did not go easy with the hammer & pipe wrench as shown in the video. It was also very hard to remove the bottom spin bearing I had to cut the bearing retainer with a dremel tool so I could get my puller on it. After I struggled to get it apart The repair went very easy, I used brake spring pliers to remove the springs it worked like a charm. I am very pleased with... Read more
Seals blower housing to prevent air leaks and lint escape. Replace when you notice lint buildup in your home or reduced drying efficiency. Confirm fit with your model number.
Took the front panel off (the door front), disconnected the connector to the door switch and used a wooden clothespin to bypass the door switch. Turned on the dryer to locate loud squeaking sound and found it was coming from the motor area. When I started to take the blower section apart from the motor, that is when I saw the "blower wheel" slipped off the motor shaft. The blower wheel has a "C" clip retainer and compression ring to keep it snug on the motor shaft (but it was loose). Now I... Read more
Seals the top of the outer tub to prevent leaks and splashing. Replace if cracked, worn through, or gasket is compressed causing water to escape onto the floor.
Removed the old tub cover/gasket by removing the front panel and top lid. Then, unclipped the tub cover. Read more
Replace this washer gasket seal to stop leaks between components. Worn gaskets cause water leakage and poor performance. Verify fit with your model.
Pop rivet secures sheet-metal panels, brackets, and burner jar lids on appliances. Replace missing, drilled-out, or damaged rivets for permanent hold.
Washer won't spin or spins weakly? A worn clutch plate causes slipping and shuddering during spin cycles. Moderate DIY repair restores reliable performance.
Found the wonderful parts diagrams you most generously share online and a couple of YouTube videos . I determined it should be repairable. In my cast the agitator shaft was frozen (rusted) in place. I was very fortunate to have been able to eventually remove it with the use of a lot of BP penetrating oil and heat. Long and short the replacement parts fit perfectly and the washer is running like new. Special thanks to the online support make my repair possible. Read more
Replacement bolt for securing panels, brackets, and assemblies in laundry centers. Needed when original fastener is stripped, missing, or damaged.
Single screw used to secure panels, brackets, and internal components to the dryer frame. Replaces lost, stripped, or damaged fasteners during repairs.
At first i just bought the belt, started dryer and off came the belt, and yes it was in place,looking at the idler arm it had a lot off back and forth movement so i ordered the whole assembly but the spring which no one has.put it all together again but drum barely turned.. so back apart and belt was in place. took the idler spring out cut 4 loops off it re did the end so it would hook on idler arm.and that did the trick.runs like new. Read more
A single mounting screw designed to secure panels, brackets, or components on your appliance for reliable fit and reduced vibration. Use this genuine replacement when a fastener is missing, stripped, or rusted. What it does:
Used Google to research issues. We ordered a new motor and springs. Installed and washer running like new. Read more
This idler pulley guides and maintains tension on the dryer drive belt to help the drum rotate smoothly. Replacing a worn pulley restores correct belt tracking and reduces noise from rubbing or slipping. What it does
I emailed appliancepartspros.com with what my problem was and they informed me what was wrong they gave me a part number to order, tools needed and a brief explanation how replace the seal. they also have online video's for different repairs. I watched the video for lip seal(part # 207843) replacement.I also had to remove the brake assembly in order to replace the seal so I watched that video also. I went online and got the part numbers for items I needed to make my repairs.Just follow the... Read more
Spesc: #12 pozi - drive
Torx-head screw set secures panels and components throughout your laundry center. Replace worn, stripped, or missing fasteners to keep parts tight.
Removed the agitator, then the spacer and lock screw, then the inside tub, then the mounting stem I replaced the agitator collar to fix the issue The hardest part on this project was removing the locks with the spanner wrench. It is not easy to break loose if the machine has never been repaired in 15 years. You need the rubber hammer and really hit hard to get loose. This is what took the longest. (Approximately 1 hour for me) Read more
Hex-head screw secures the bearing insert in your washer. Replace if stripped, missing, or damaged to restore proper bearing alignment and retention.
Replaced the drain pump. Read more