Maytag Neptune Front Loader Washer Parts

This small tube of Molykote lubricant helps reduce friction on moving appliance parts for smoother operation and quieter performance. Use it where the manufacturer specifies a silicone/grease lubricant to restore proper movement and limit wear. What it does:

• Lubricates bearings, rollers, hinges, and other sliding contacts to reduce noise and friction
• Helps parts move more smoothly and can prevent rough operation or squeaks
• Can protect metal-on-metal contact from premature wear when applied as directed
• For use only in areas the manufacturer specifies for Molykote-type lubricants

• Apply sparingly to the specified contact points; excess can attract dirt or drip onto other parts
• Wear gloves and avoid skin/eye contact; wash hands after use
• Keep out of reach of children and store in a cool, dry place

This door hinge secures and guides a refrigerator door, restoring proper alignment and smooth opening/closing. Replaces a worn or damaged hinge to reduce sagging, rubbing, or uneven gaps and help maintain a tight door seal. What it does:

• Provides the pivot point that supports and aligns the refrigerator door
• Restores correct door height and gap to prevent rubbing or catching
• Helps the door close fully to maintain proper temperature and efficiency
• Reduces sagging or drooping that can cause seal and cooling issues

• One door hinge

• Disconnect power to the appliance before beginning any repair to avoid electrical hazards
• Support the door during removal/installation to prevent injury or damage to the cabinet
• Use the same fasteners provided or retained from the original hinge; torque per manufacturer guidelines
• Adjust hinge position per service instructions

This pressure switch senses and signals the washer's water level so the machine fills and cycles correctly. Replacing a failing switch restores accurate water-level sensing for consistent wash performance. What it does:

• Monitors tub water level and signals the control board to start/stop filling.
• Helps the washer advance through fill, agitate, and drain cycles based on detected water height.
• Common symptom: washer overfills, underfills, or fails to advance cycles.
• Works with existing pressure hose and wiring harness to relay air pressure changes.

• Disconnect power and water to the appliance before beginning any work.
• Note and photograph hose and wiring positions before removal to ensure correct reinstallation.
• Inspect or replace the small pressure hose if cracked or clogged; ensure a tight, leak-free connection.

This power cord supplies electrical power to the appliance and replaces a damaged or worn cord to restore safe, consistent power delivery. The "as wrapped" packaging means the cord ships neatly coiled for protection in transit. What it does:

• Provides the appliance's main AC power connection so it can operate
• Replaces frayed, cut, or otherwise damaged cords to eliminate power loss
• Can resolve symptoms like no power, intermittent power, or visible cord damage
• Designed for direct replacement where the OEM cord mounts and terminates the same way

• Unplug the appliance or disconnect power at the breaker before servicing
• Route the cord and attach with the existing strain relief or mounting bracket
• Ensure connections match the original cord terminals and are tight

This inner door panel provides the interior surface of the appliance door and restores a finished appearance while protecting inner components from heat and debris. It's a direct-replacement exterior-facing inner panel in bisque. What it does:

• Replaces a cracked, dented or warped inner door surface to restore appearance and protect internal door parts
• Helps maintain proper heat containment and prevents debris from reaching insulation and electronics
• Provides the correct mounting surface for inner trim, glass, and fasteners
• Can reduce rattle or movement caused by damaged inner door structure

• Disconnect power to the appliance before beginning any door repair
• Handle edges and any attached glass with care; use gloves and eye protection
• Follow for door disassembly/reassembly and hinge alignment
• Test door closure before returning appliance to service

This sliding gear latch replaces the latch gear that secures the appliance door and helps engage the door lock mechanism for normal operation. It restores reliable door latching so cycles can start and run properly. What it does:

• Replaces the sliding gear used by the door latch assembly to engage/disengage the door lock
• Helps restore a door that won't stay closed or won't latch reliably
• Addresses symptoms like a door that won't lock, intermittent latch engagement, or door-related cycle start failures
• Works as a direct-fit internal latch gear when the original is worn or broken

• 1 sliding gear latch

• Unplug the appliance or disconnect power before beginning any repair
• Access may require removing the door panel or latch housing—keep fasteners organized for reassembly
• Install the part in the same orientation as the original; verify smooth movement of the latch mechanism before reassembling

This self-drilling screw secures appliance panels and components where a fastener must cut its own pilot hole. It provides a quick, reliable hold for repair or reassembly of trim, brackets, and internal fixtures. What it does:

• Fastens panels, brackets, and small components without pre-drilling
• Helps stop loose or rattling trim and parts caused by missing or worn screws
• Restores proper alignment and secure mounting after repairs
• Works where sheet metal or thin substrates require self-tapping engagement

• One self-drilling screw

• Disconnect power and follow appliance safety procedures before starting repairs
• Use the correct size driver and steady pressure to avoid stripping the head
• Start straight and apply firm, even torque; avoid overtightening which can damage mounting surfaces
• Wear eye protection and handle small fasteners carefully to avoid loss or ingestion hazards

This replacement axle/latch spring secures the latch/axle assembly so the appliance door or panel stays engaged during use. It restores proper latch tension for reliable closing and operation. What it does:

• Applies tension to the latch/axle so the door or access panel stays closed and latched
• Helps ensure the appliance detects a closed door and will start or run normally
• Common symptom: door won't stay closed or latch feels loose or fails to engage
• Small metal spring designed for a specific latch assembly — not a universal part

• Disconnect power to the appliance before starting any repair
• Access may require removing a panel, bezel, or door — use proper tools and keep fasteners organized
• Handle the spring and latch components carefully; springs are under tension and can snap free

The Washer Screw-Tapping Assembly is essential for maintaining your Samsung washer's structural integrity. This genuine OEM part ensures precise fitting and reliable performance, matching the original specifications of your appliance. Designed for seamless installation, the Screw-Tapping Assembly helps secure various components, preventing loosening and ensuring your washer operates smoothly. By using this genuine OEM part, you guarantee compatibility and durability, enhancing the longevity of your washer. Whether you're repairing a damaged assembly or replacing worn-out screws, the Washer Screw-Tapping Assembly offers a dependable solution. Its high-quality construction withstands the demands of daily use, providing stability and support to critical parts of your washer. This assembly reduces the risk of further damage by maintaining secure connections, which can improve overall appliance performance. Trust in this high-quality component to maintain the optimal functionality of your Samsung washer, providing peace of mind and a hassle-free repair experience. Investing in the Washer Screw-Tapping Assembly ensures your appliance continues to perform efficiently, keeping your laundry routine uninterrupted.

This is a replacement mounting screw used to secure panels, brackets, and internal components on compatible appliances, restoring proper fit and reducing rattles or loose parts. What it does:

• Secures panels, trim, brackets, or internal assemblies
• Stops rattling or vibration caused by missing or loose fasteners
• Replaces a lost or stripped screw to restore proper alignment
• Works as a direct-fit hardware fastener when the OEM screw is damaged or missing

• Turn off and unplug the appliance before servicing
• Use the correct screwdriver or bit to avoid stripping the head
• Do not overtighten; snug until secure to avoid cracking plastic or stripping threads