Need Help?
Call or text
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
This hose clamp secures a hose connection to prevent leaks and keep your appliance running smoothly. It provides a tight, reliable hold on the hose fitting so water or air stays contained during operation.
Took off cover, installed new parts. Read more
This float palnut is a push-on retainer that secures the dishwasher's water-level float to its stem. Keeping the float anchored helps the overfill protection work properly, supporting correct fill levels and helping prevent leaks from overfilling. What it does:
I first installed the inlet pump with no results. I then ordered a Control Switch and Float and Nut. This fixed the problem. Everything comes out so clean. I also replaced the filter which allowed me to clean debris around old filter. It is also easier to replace all these parts with the dishwasher pulled out and tilted on its side. I had to pull mine out to unplug power to the dishwasher. Read more
Fix poor cleaning and broken spray arms with this dishwasher impeller kit. Restores water pressure and quiet operation. DIY-friendly repair.
Followed the instructions on the video you guys sent me. Read more
Fix a cracked or broken door handle that's hard to open or close. This dishwasher door handle typically takes 10-15 minutes to replace.
I installed the door latch assembly and handle. It worked fine after that. Read more
Replacement tub wheel assembly for dishwasher upper rack track. Installs on inner tub to support rack gliding. Needed when wheel is cracked or broken.
Replaced left hand rack adjuster. Read more
This is the longer of the two dispenser lid hinge pins. For the shorter lid hinge pin order WPY912679.
The foam was shot on the detergent cup lid. Hard as a rock. Causing caking problems, dribble down the inside wall of the door and leaving lumps of detergent. Cut the door in half wit aviation snips and pulled out the two halves. Discovered at this point that the spring had gone soft. Bought one ahead of time, so I was set. Put the spring on the left pin, put the spring pin in the door, slipped the door into place (open) and put the right pin in with pliers. Door snaps open now. Read more
Insulates your dishwasher tub to reduce noise and maintain temperature. Replace if worn, damaged by pests, or causing odors. Confirm fit with your model.
Replaced the insjulation blanket Read more
This is the shorter of the two dispenser lid hinge pins. For the longer lid hinge pin order WP6-912678.
Secures the power cord where it enters the cabinet, protecting the jacket and preventing pull on internal connections. Replace if cracked, broken, or missing.
Dishwasher won't start or stops mid-cycle? A faulty door switch prevents operation when it can't detect the closed door. Simple DIY repair.
This small rubber grommet seals the opening around the dishwasher's detergent/rinse-aid dispenser, helping prevent leaks and moisture intrusion so the dispenser operates reliably throughout the wash cycle.
After discovering your web site and reading of others issues I ordered a door seal (my old one was a little short on the right side) a detergent door grommet, and the 2 water deflectors ( I decided to cover all the bases while I was at it. Very simple job with the information provided on your web site. I certainly have the confidence to tackle other appliance repair now. Read more
Rear bowl tine for dishwasher lower rack. Replace when rusted, cracked, broken, or missing. Snaps into place on rack to hold bowls securely during wash.
I ordered new replacement parts. Read more
Protects tine tips from rust and prevents dish scratching. Replace when cracked, missing, or worn to extend rack life. Confirm fit with your model.
I watched the video on your website and followed your demonstration. Easy! Read more
The Tub Wheel supports and guides the washer's tub assembly on its base during wash and spin cycles. Replacing a worn wheel restores smoother, quieter operation and helps reduce vibration and rubbing as the machine operates.
Specs: No.8X1/2 HEX WASHER HEAD
Replaced the control board after removing the inner door liner, plastice board cover and board itself, by removing screws, working various plastic clips/tabs and unclipping wire harnesses from board. most of time was spent cleaning the black soot from the door, which had a terrible burnt electrical/plastic fire smell. Cleaned mold/scale off of as much of the door as I could while in there as well. Removing parts without breaking plastic tabs to hold the new parts was trickiest part. Read more
Screw: 8-16 x 3/8 inch.