Need Help?
Call or text
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
This float palnut is a push-on retainer that secures the dishwasher's water-level float to its stem. Keeping the float anchored helps the overfill protection work properly, supporting correct fill levels and helping prevent leaks from overfilling. What it does:
I first installed the inlet pump with no results. I then ordered a Control Switch and Float and Nut. This fixed the problem. Everything comes out so clean. I also replaced the filter which allowed me to clean debris around old filter. It is also easier to replace all these parts with the dishwasher pulled out and tilted on its side. I had to pull mine out to unplug power to the dishwasher. Read more
Replacement tub wheel assembly for dishwasher upper rack track. Installs on inner tub to support rack gliding. Needed when wheel is cracked or broken.
I got the new hose with connection at faucet in only 2 days after ordering. After taking the top and sides off if the dishwasher it only took 10 minutes to replace the hose. It actually took longer to disassemble and reassemble the top and sides but even that was easy. 45 minutes total. Just use your cell phone to take a picture of how the old hose is routed before installing the new one and have 2 small zip ties to keep loose wires away from hose. Read more
Fix a cracked or broken door handle that's hard to open or close. This dishwasher door handle typically takes 10-15 minutes to replace.
I installed the door latch assembly and handle. It worked fine after that. Read more
This is the longer of the two dispenser lid hinge pins. For the shorter lid hinge pin order WPY912679.
The foam was shot on the detergent cup lid. Hard as a rock. Causing caking problems, dribble down the inside wall of the door and leaving lumps of detergent. Cut the door in half wit aviation snips and pulled out the two halves. Discovered at this point that the spring had gone soft. Bought one ahead of time, so I was set. Put the spring on the left pin, put the spring pin in the door, slipped the door into place (open) and put the right pin in with pliers. Door snaps open now. Read more
Insulates your dishwasher tub to reduce noise and maintain temperature. Replace if worn, damaged by pests, or causing odors. Confirm fit with your model.
Mice and insulation gone. cleaned dishwasher replaced insulation pad. reinstalled dishwasher smell is gone all is well. Read more
This is the shorter of the two dispenser lid hinge pins. For the longer lid hinge pin order WP6-912678.
To order indicator lens use WP22001948.
Small metal clip that secures panels, brackets, or tubing in place inside appliances. Replace if bent, fatigued, or missing to restore secure mounting.
Here's the story. All my appliances except the dryer broke. Yeah. talk about bad luck. First I tried to fix the refrigerator. Replaced both motherboard and inverter board. Now it wakes up but the compressor does not kick in. Need another part. The washer, well I have to pull out the sink to get enough room to pull out the washer to fix it. Since the refriigerator is still in the middle of the kitchen, I don't need to tear apart another room. Nevertheless, let me say this, I love my "older"... Read more
Protects tine tips from rust and prevents dish scratching. Replace when cracked, missing, or worn to extend rack life. Confirm fit with your model.
Parts came fast and the videos were very helpful. It showed which way the tine went, dishwasher rack back working. Read more
Screw: 8-16 x 3/8 inch.
Replacement screw secures appliance panels, brackets, and internal components. Needed when original screws are stripped, missing, or damaged during repair.
I watched a 3 minute video on You Tube on how to replace a refrigerator door handle and it took me 3 minutes to replace mine. Super easy! Read more
Creates a leak-resistant seal between pump components and connections. Replace when you notice water leaking during drain cycles or around fittings.
I first wanted to get the dishwasher running, before ordering the spring links. So I disassembled the pump / motor assembly to determine the reason the motor would not start. My wife cleaned all of the parts in the pump assembly. I took the motor apart and discovered that the lower bearing ( a sleeve type bearing) was dry and dirty, and was the culprit for the motor seizing. I cleaned up the bearing and lubricated it with SAE 20W. I also packed felt inside the cavity adjacent to the bearing.... Read more
The Tub Wheel supports and guides the washer's tub assembly on its base during wash and spin cycles. Replacing a worn wheel restores smoother, quieter operation and helps reduce vibration and rubbing as the machine operates.
Specs: No.8X1/2 HEX WASHER HEAD
Replaced the control board after removing the inner door liner, plastice board cover and board itself, by removing screws, working various plastic clips/tabs and unclipping wire harnesses from board. most of time was spent cleaning the black soot from the door, which had a terrible burnt electrical/plastic fire smell. Cleaned mold/scale off of as much of the door as I could while in there as well. Removing parts without breaking plastic tabs to hold the new parts was trickiest part. Read more
Gray plastic cap that threads onto the center of your dishwasher's lower spray arm assembly. Replaces cracked, broken, or missing caps. Hand-tightens.
I was able to locate the model number and enter this on the website which gave me an expanded view of all the parts for my model. From this I was able to determine which parts I needed and order them. Customer Service was Excellent for Helping me make the right choices. The parts were cheapest here then any other website I found and they shipped to my home in less than 3 days! Now my dishwasher works like new! Thank You AppliancePartsPro for all your help and getting me the parts I... Read more
Twin-wheel caster for portable dishwashers. Replaces worn, broken, or missing wheels to restore smooth rolling and prevent floor scuffing. Installs at base.
The part came next day! I was shocked at how fast the shipping was. I turned the dishwasher on its side used a pair of pliers and a rubber mallet to get the old wheel off( was not easy) once it was off I had to get the plastic off the new wheel , and that was really hard took some elbow grease but finally after about 10 mins I got it off and simply pushed in the new wheel and used the rubber mallet to secure it and my dishwasher now rolls around like new. Read more