We use cookies and similar tools for site analytics and advertising. By using our site, you agree to this. See our Privacy Policy for details. Do Not Sell or Share My Personal Information
Need Help?
Call
The Timer Knob Insert is an OEM replacement part for Whirlpool dryers. This is a cap located on the timer knob on the control panel. Color: White. This is the timer knob cap only. For the complete assembly, you must also order the knob and skirt. Causes of timer knob Insert failure can include cracked plastic from years of repeated turning motions. Wear on components also occurs due to extensive lifetime usage cycles. Symptoms of a faulty timer knob insert include:
This is a genuine Whirlpool OEM replacement this part is also compatible with Maytag, Jenn-Air and some Kenmore models.
It's working now Read more
This Hex Nut is a small but critical fastener used to secure brackets, panels, and internal assemblies in your appliance. Replacing a stripped, corroded, or missing nut restores a tight, rattle-free, and safe installation.
It took me about 2 hours to take everything apart and get it back together & running again with no problems. All the parts I ordered were exactly what I needed to fix everything. Thank you all !!! Read more
Dryer not heating or producing warm air? This heating element assembly often solves no-heat issues. DIY-friendly repair, typically 10-20 minutes.
I figured there could only be a couple reasons why the dryer would not heat so I did some research. I read where you could test for continuity on the parts to determine which one was bad. A friend referred me to this site, I looked up the part for my particular model, ordered and replaced the part. It could not have been any easier. I will come back to this site with my future appliance parts needs for sure! Read more
Fix a dryer that won't shut off or runs continuously. This timer controls cycle timing and automatic shutoff. Most DIYers complete in 15-30 minutes.
Installed this part and it was working good as new in 15 minutes! Read more
This internal-bias thermostat regulates dryer drum temperature by cycling the heat on and off, helping maintain consistent drying performance and protect against overheating.
Cleaned exhaust duct, but only from the dryer/laundry room side. Replaced thermal fuse. Unit worked for about two loads and thermal fuse blew again. This time I cleaned the exhaust vent on the roof of my 2-story house. It was found to be partially obstructed and I was able to remove a significant amount of lint from it. Also, I researched the problem and followed someone's advice to replace the cycling thermostat together with the thermal fuse if the thermal fuse blows. So far it has been... Read more
Seals the dryer door to keep heat and moisture inside the drum. Replace when worn to restore airflow, improve drying, and stop lint escape.
I replaced the gasket that you had sent to me the next day in about 5 minutes! Sears parts direct had the item back ordered and even when I cancelled the order, they still shipped it! I will never use them again! All my appliance part needs will be through Appliance Parts Pros! Read more
Dryer making loud noise or won't dry? A cracked or loose blower wheel often causes poor airflow. Moderate DIY repair, 1-2 hours with basic tools.
I disassembled my dryer and found that the fan(blower wheel) was "free-spinning" on the motor shaft. A common problem with this model Maytag dryer. I also discovered that the right drum roller (drum support roller) was in the process of failing. Note: the fan drive was frozen on the motor shaft, this was the threaded type of motor and fan assembly. I was able to remove the fan drive by using vice-grip pliers, hammer and a combination wrench to hold motor from turning. Also Note: the fan... Read more
This jumper wire connects two terminals in an appliance circuit to maintain proper electrical continuity. Replacing a burnt or damaged jumper restores reliable connections so switches, heating elements, and controls receive power as designed.
Replaced jump wire and thermostat. Read more
To order indicator light use WP903115.
I changed both the Control Panel and the Oven Control Board. Since I had previously changed the Oven Control Board, this was a fairly quick fix. I was also able to change out one of the Indicator Lens that had been broken. Read more
This is a metal clip that secures the drive motor in place within the dryer cabinet. It clamps around the motor housing to prevent movement during operation. Replace this clip if it is broken, missing, or bent, which can cause the motor to shift and create excessive vibration, rattling noises, or belt misalignment.
Ultimately is was discovered and caused by the blower wheel shaft opening was cracked and broken. Replaced blower fan wheel. Read more
This dryer blower housing encloses the blower wheel and directs air from the drum through the lint filter to the exhaust vent. Replacing a damaged housing restores proper airflow for consistent drying and helps keep lint contained within the airflow path.
Replacement screw secures panels, brackets, and internal assemblies. Needed when original hardware is stripped, corroded, or missing to keep parts tight.
Specs: No.8X1/2 HEX WASHER HEAD
Replaced the control board after removing the inner door liner, plastice board cover and board itself, by removing screws, working various plastic clips/tabs and unclipping wire harnesses from board. most of time was spent cleaning the black soot from the door, which had a terrible burnt electrical/plastic fire smell. Cleaned mold/scale off of as much of the door as I could while in there as well. Removing parts without breaking plastic tabs to hold the new parts was trickiest part. Read more
This factory replacement hinge screw secures the door hinge to the appliance cabinet or door. Replacing a worn or missing screw restores solid door mounting and alignment for safe, reliable opening and closing.
Replaced coils on gas valve; while at it replaced door screws which were starting to wear from assorted repairs over the years. Read more
Secures the door latch strike to the dryer frame for reliable closing. Replace if your bracket is bent, damaged, or missing to restore proper alignment.
Screw: 8-16 x 3/8 inch.