We use cookies and similar tools for site analytics and advertising. See our Privacy Policy for details. Do Not Sell or Share My Personal Information
Need Help?
Call
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Fix LF error codes, slow filling, or no cold water issues. This washer water inlet valve controls water flow into your machine. DIY repair in 15-20 minutes.
Our original discussion with a parts rep. led us to change the control panel as we had tested the valves for continuity and had it. Changing the panel did not fix the problem. As we had power continuity, we then removed the hoses from the cold water valve and checked the flow. The wash fill side of the valve had only a trickle of water, so we ordered a new cold inlet valve and replaced it. Problem solved, washer working like it's new. Read more
Dryer won't heat or overheats? The high limit thermostat monitors drum temperature. Moderate DIY repair with heater housing access required.
I purchased a new heating element. Very easy to fix in about twenty minutes Read more
Houses and secures the lint filter in your dryer. Replace if cracked, warped, or broken to prevent lint bypass and maintain airflow. Verify fit by model.
Bought a new lint screen housing and top flapper. Probably didn’t need the flapper but I didn’t want to set into the repair and find out I did need it. Read more
This is a felt seal strip that attaches to the front bulkhead panel of the dryer where the drum meets the front of the cabinet. It creates a soft barrier that prevents heated air from escaping and keeps clothing from getting caught between the drum and the panel. Replace this seal if your dryer is taking too long to dry clothes, you feel hot air leaking from the front, or you hear squeaking or scraping sounds as the drum turns.
First I watched videos about squeaking Kenmore dryers. Then I used that information to open the dryer, diagnosing the fact that the roller on the drum belt tension arm had broken and actually fallen off the arm. The dryer was filled with lint and dust/dirt, so I also saw that the seals on the dryer had deteriorated greatly. AppliancePartsPros website is outstanding, far better than its competitors. This made it easy to find the parts and videos that I needed. It took hours to pull everything... Read more
Replacement dispenser hose channels detergent from the tray to the wash drum. Needed when original is cracked, torn, or leaking due to wear or rubbing.
Removed the leaking hoses and seal. Installed the new ones. They all fit perfectly. The disassembly/reassembly of the washer took the most time. Read more
Dryer won't heat or stops working? A burnt or melted terminal block disrupts power flow. DIY repair in under an hour with video guidance included.
I ordered the parts through AppliancePartsPros.com. They were delivered the next day. I installed them and the dryer works great. Read more
Dryer drum belt transfers power from motor to drum for smooth tumbling. Replace if dryer won't start, drum doesn't turn, or you hear squealing.
If your dryer won't stay lit or shuts off after a few minutes, the gas limiter may be faulty. This regulator controls safe gas flow to the burner.
Removed LP Orifice and LP Gas limiter. Orifice was easy, however the gas limiter was the tricky one because I had no instructions to what went where. I could not find anything online as to how to convert from LP to Natural Gas, but you could find several things as to how to convert from Natural to LP. I ended up finding the Dryer schematic on line for the Whirlpool Duet natural gas dryer and was able to figure out what sequence the Spring, regulator and limiter went in. The order I just... Read more
This screw is used to secure the handle end cap to the center of the door. The screw size measures 8-18 x 1/2 inches.
This was actually one of the easiest fixes I’ve done. All that was required was to remove 3 screws to remove the broken part. I used a pair of pliers to remove the moisture sensors from the broken part to the new one. Read more
The washer is an OEM replacement part for Whirlpool clothes dryers. This part is located on the drum roller support shaft in your dryer. The exterior of the washer is 1 inch in diameter with a hole in the middle and is made of metal. They are installed alongside the drum support rollers and idler pulleys. They help prevent the rollers and pulleys from bumping up against the brackets they are installed on. If you are replacing the rollers, we suggest you replace the washers at the same time. Causes can be normal wear to bearing surfaces over extended use cycles. Accidental impacts may also potentially bend or damage shaft components. Symptoms of a bad roller shaft include:
This is a genuine Whirlpool OEM replacement this part is also compatible with Maytag, Jenn-Air and some Kenmore models.
Replaced the roller, shaft, rings and washer. After removing the back, reverse threading the nut off, discarding the old hardware and installing the new hardware back in business in about 20 minutes. Read more
Dryer won't heat or shuts off early? The high limit thermostat monitors temperature and cuts power when overheating occurs. DIY repair in 30 minutes.
The 2 sensors that sit on top of the flame tube work together. The Thrmst F should check closed, as should the Cutoff-TML, in order for power to flow to the ignitor. If the Cutoff is open, it is usually because the Thrmst-F did not open soon enough. The Thermst-F will cycle, closed to open, and repeat, however the Cutoff-HTML is a one time switch. If it opens it will not return to closed, and subsequently the ignitor will not glow. Some professionals say that if one of these sensors fail, both... Read more
Connects the outer tub to the drain pump in your washer. Replace if cracked, leaking, punctured, or worn. Includes check ball housing for proper drainage.
Took the old part off and fitted the new one. I used the old plastic ball from the old hose and it worked fine. Next time I would replace the original clamp with a 4 inch hose clamp. The original clamp is way tooooooooooo hard to put back on....with a different clip it would be a 10 minute job at most. Read more
Fix LF or F20 error codes and slow fills with this water inlet valve. Controls water flow into washer during cycles. Moderate DIY repair, 30-45 min.
Called a repair man after not being able to determine the exact problem. Narrowed it down to valves, level switch or mother board. Repairman took money for parts and then said he couldn't find them. Went online and found this site, ordered parts Monday, had them by Thursday noon. Had machine running by 1. Read more
Screw secures appliance panels and access covers. Replace missing, stripped, or corroded screws to restore tight fit and eliminate rattles or gaps.
After several attempts at Local Hardware stores and Lowe's and Home Depot to find them I called AppiancePartsPros.com. I gave them the model number and what I was looking for and customer service directed me to the part on the Web site. They were extremely helpful and it was very fast and I got the parts the next day. Read more
Dryer won't power on or has loose power cord connection? This terminal block screw kit secures electrical connections. Easy DIY fix in 15 minutes.
And after replacing the thermal fuse The dryer turned on. Read more
Dryer not heating? A faulty heating element is often the cause. This part generates heat to dry clothes. DIY-friendly repair, takes 30-60 minutes.
Put in new part. It was done by maintenance personal and took just a few minutes. Read more