Mtf2155ar Parts

The Dishwasher Rack Roller is an OEM part for Whirlpool dishwashers. It is designed to facilitate the smooth movement of the dishwasher rack in and out of the appliance. This roller ensures that loading and unloading dishes is easy and efficient, allowing the rack to glide effortlessly along the tracks.

Over time, dishwasher rack rollers can wear out or become damaged due to frequent use or accidental mishandling. Causes of a bad roller include general wear and tear, buildup of debris, or impact damage.

Symptoms of a bad roller include:

• Difficulty sliding the rack in or out
• The rack becoming stuck or jammed
• Uneven movement of the rack
• Excessive noise when moving the rack

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This grommet is a small protective seal used where a hose, tube, wire, or component passes through or mounts to the appliance cabinet. It cushions the connection and helps prevent leaks, vibration, and wear for reliable operation.

• Provides a snug barrier between parts and metal openings to protect hoses, tubes, and wiring
• Helps seal against moisture to reduce seepage
• Dampens vibration and rattling noises
• Replace if cracked, hardened, missing, or no longer stays seated; symptoms may include drips at a pass-through, buzzing/rattling, or a loose fit

• Disconnect power; shut off water supply if applicable
• Access the grommet location and note orientation/routing
• Remove the old grommet and clean the opening
• Press the new grommet fully into place; reassemble and test for leaks/noise

This white freezer door handle restores a secure, comfortable grip and refreshes the appliance's appearance. Replace a cracked, loose, or missing handle so the freezer door opens and closes smoothly again. What it does:

• Replaces a damaged, worn, or missing freezer door handle
• Restores proper grip and leverage for normal door operation
• Helps address loose or wobbly handle conditions
• Matches the original white finish for a clean, uniform look

• Wear gloves and protect the door surface to avoid scratches
• Support the handle while loosening/removing existing fasteners
• Reuse existing hardware as designed; start screws by hand and tighten just until snug
• Check alignment and security before returning the appliance to service

This light socket replaces a worn or heat-damaged lamp holder so your appliance light works reliably again. Its straight-connector design fits applications with in-line wiring, ensuring a secure electrical connection to the interior light bulb.

• Holds the light bulb and supplies power to it
• Restores interior illumination for better visibility
• Straight terminal orientation for housings requiring inline wiring clearance
• Typical signs of failure: light stays off with a good bulb, flickers, or shows heat damage at the socket

• Disconnect power at the breaker or unplug before servicing; allow the area to cool completely
• Remove any lens/cover; transfer wires one at a time to maintain correct connections
• Secure the socket with existing bracket/fasteners; do not overtighten
• Test light operation before reassembly and confirm the door switch activates the light

This PTC start relay mounts on the compressor and briefly powers its start winding to get it running, then drops out. Replacing a weak relay can restore reliable starts and resolve clicking/humming with no cooling.

• Provides the initial boost to the compressor via a positive temperature coefficient (PTC) element, then opens as it heats
• Takes the start winding out of the circuit once the compressor is running
• Typical failure symptoms: compressor won't start, repeated clicking/humming, no cooling, visible heat damage at the relay or connector
• Direct replacement for the original PTC start device used on applicable models

• Disconnect power before servicing; allow hot components to cool
• Access the compressor compartment, remove the cover, and note the relay's orientation; pull the old relay straight off the compressor pins
• Inspect wiring terminals for heat damage; do not reuse burnt connectors
• Firmly seat the new relay on the compressor terminals, reinstall the cover, restore power, and verify compressor start

Ice stripper removes ice cubes from the ice maker mold so the dispenser or storage bin fills properly. Replacing a worn or broken stripper helps the ice maker eject cubes cleanly and reduces ice jams or stuck cubes. What it does:

• Pushes or guides harvested cubes out of the ice mold into the bin during the ice maker's harvest cycle.
• Prevents cubes from sticking in the mold; a damaged stripper can cause incomplete ejection or leftover ice in the mold.
• Works with the ice maker's ejector mechanism to maintain consistent cube release and storage.
• A faulty or broken stripper may lead to noisy operation, partial fills, or visible ice build-up in the mold.

• Disconnect power to the appliance before starting any repair to avoid electrical shock.
• Remove the ice maker or access panel per the manufacturer's instructions to reach the stripper; keep small parts and screws organized.
• Inspect the ice mold and surrounding components for damage or ice build-up; clear ice before installing the new stripper.
• After installation, restore power and run a test harvest cycle to ensure proper cube ejection.

This replacement roller mounting screw secures the dryer drum roller or roller bracket to keep the drum aligned. Installing the correct screw restores proper roller position and helps reduce drum wobble and rubbing noises. What it does:

• Fastens the dryer drum roller or roller bracket to the dryer cabinet or shaft
• Keeps the roller aligned so the drum rotates smoothly
• Prevents the roller from shifting, which can cause scraping, squealing, or banging noises
• Helps avoid premature wear of the roller and drum seal caused by misalignment

• Disconnect power (and gas supply for gas models) before starting any repair
• Use appropriate hand tools; avoid power drivers that may strip the screw head
• Do not overtighten — snug to secure the roller without deforming the bracket or shaft
• Inspect the roller, shaft, and mounting hardware; replace any worn components for a lasting repair

This defrost thermostat senses the evaporator coil temperature and controls the defrost heater. Replacing a failed thermostat restores proper defrosting to prevent heavy frost buildup and helps your refrigerator keep consistent, reliable cooling.

• Monitors evaporator temperature to allow the defrost heater to energize and to terminate the cycle as the coil warms
• Protects against overheating in the evaporator area during defrost
• Failure symptoms include frost/ice buildup on the evaporator cover, reduced airflow, fresh food section warming, or the unit not defrosting
• Typically mounts clipped to the evaporator tubing inside the freezer

• Disconnect power before servicing and remove the freezer's rear panel to access the evaporator
• Transfer the clip/bracket if present and mount the new thermostat in the same location, ensuring firm metal-to-metal contact with the evaporator tubing
• Route wires away from the heater and moving parts; secure connections and reassemble panels before restoring power
• Wear cut-resistant gloves—sheet-metal edges can be sharp

This heater clip secures the defrost heater in your refrigerator. Keeping the element properly positioned helps the defrost system work as designed and reduces rattling or damage from a loose or misaligned heater.

• Holds the defrost heater securely in place on its mounting point
• Helps maintain correct heater placement for consistent frost removal
• Replace if the clip is missing, broken, bent, or corroded
• Common symptoms include a loose/dangling heater, rattling noises, or recurring frost/ice around the evaporator area

• Disconnect power before servicing the appliance
• Access the defrost heater behind the freezer's rear panel; note the original clip orientation
• Install the new clip so the heater is seated and not contacting wiring or plastic; do not deform the element or coils
• Restore power and verify the heater is secured in place

Kit was recently redesigned by manufacturer. Instructions included.

This is the refrigerator's sealed-system compressor. It pressurizes and moves refrigerant through the system to remove heat from the cabinet, restoring consistent cooling performance when the original compressor has failed or lost capacity. What it does and common symptoms:

• Pumps and circulates refrigerant through the evaporator and condenser to remove heat
• Maintains target temperatures in both fresh food and freezer sections
• Symptoms of failure can include: no cool/poor cooling, unit warms up after short operation, humming then clicking from the compressor area, or repeated thermal overload trips
• Runs but not cool effectively when the compressor is weak or internally damaged (after ruling out start components and charge issues)

• 1 compressor

• Disconnect power before servicing; sealed-system work involves high pressure and high temperatures
• Sealed-system repairs require EPA Section 608 certification and specialized tools (gauges, vacuum pump, brazing equipment)
• Replace the filter-drier, braze connections properly, evacuate to deep vacuum, and charge to the model's specification
• Related components (start device/overload, run capacitor, controls) are tested before condemning the compressor

This support mounts in the dispenser area to secure the ice housing assembly. It helps keep the chute and door properly aligned so ice dispenses smoothly and the opening seals as designed.

• Supports and positions the ice housing/chute assembly in the freezer door
• Helps maintain proper alignment and sealing of the ice door/flapper
• Reduces wobble or flex that can affect dispensing performance
• Typical signs it may be needed: loose or misaligned dispenser housing, ice or air leaking at the chute, frost buildup around the dispenser, inconsistent ice dispensing

• Disconnect power to the refrigerator before servicing
• Remove the dispenser trim/control to access the housing; handle wiring and tabs carefully
• Remove mounting fasteners, replace the support, and transfer any reusable hardware
• Reassemble, restore power, and test ice dispensing and chute seal

Size: 8 x 1-1/4 inch.

This replacement mounting screw secures appliance panels and components to restore proper fit and reduce rattling. Use when a damaged or missing screw causes loose trim, gaps, or vibrating noises; order by part number to ensure a match. What it does:

• Fastens panels, brackets, or trim to keep parts aligned and secure.
• Stops vibration and rattling caused by loose or missing screws.
• Common symptoms: visible gaps, loose panels, hardware falling out, or excess noise.
• Use the part number and/or existing screw to ensure correct size and thread before ordering.

• Disconnect power and water before accessing internal components.
• Use the correct screwdriver or bit to avoid stripping the head.
• Turn until snug; avoid over-tightening which can strip threads or crack trim.
• Keep small parts away from children and pets during repair.

This hinge supports and pivots the washer lid so it opens and closes smoothly. Replacing a worn or broken hinge restores proper alignment and helps the lid close securely without binding or rubbing.

• Provides the pivot point for the lid to open and close
• Keeps the lid aligned with the top panel
• Wear symptoms include wobble or sagging, squeaks, binding, or visible cracks/bending
• Misalignment may prevent the lid switch/latch from engaging properly

• Unplug the washer before servicing; have a helper support the lid
• Remove the mounting screws, noting hinge orientation for reassembly
• Transfer and reuse original screws/trim as applicable; do not overtighten
• Test lid alignment and operation before fully tightening the fasteners

This glass crisper shelf replaces a cracked or missing refrigerator crisper shelf to restore a flat, stable surface for produce storage. It provides a clear, durable platform that supports the crisper drawer and items stored above it. What it does:

• Replaces a broken or chipped crisper glass shelf
• Restores level support for the crisper/drawer area so items sit securely
• Helps keep fruits and vegetables organized and accessible
• Reduces risk of items falling into the crisper area due to missing glass

• Remove all food and the crisper drawer before replacing the shelf
• Handle glass carefully and wear cut-resistant gloves if glass is broken
• Set the new shelf gently into the support rails; it sits level before replacing the drawer
• If support rails or clips are damaged, replace those parts first