Need Help?
Call
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
If water leaks from your washer tub area, the tub ring may need replacement. This internal gasket seals the outer rim to prevent leaks. Moderate DIY.
Easily replaced by snapping the new one into place. Read more
Adjustable leveling leg threads into the washer base to support and stabilize the unit. Replace if cracked, stripped, or missing to level cabinet.
Replacement water fill hoses for washing machines. Connect home water supply to washer. Replace when cracked, leaking, or showing rubber wear or corrosion.
Motor control board was flashing 4 times, indicating that the mode shifter had an error. I disconnected the mode shifter's wire from the controller and measured the resistance between the 2 leads with an ohmmeter. Since the reading was infinite, that meant that the mode shifter coil or in-line thermal sensor was electrically open, i.e. bad. As this fix is near a complete tear-down of the washing machine, here are a few tips I discovered. 1) the hub nut is difficult to remove and you need a... Read more
This assembly includes the dispenser housing along with integrated hot and cold water inlet valves for a top-load or front-load washing machine. It controls the flow of water into the machine and routes it through the detergent and fabric softener dispensers. Replace this assembly if the washer is not filling with water, fills slowly, leaks at the inlet connections, or if the dispenser is not properly directing water to the wash tub.
Maytag Bravos Washer, Model #MVWX550XW1 My washer was emitting a loud noise - I describe it as a loud whining noise - while filling with water. The noise seemed to be coming from the fill valve assembly: 1) jiggling the supply hoses changed the inflection of the noise, 2) turning on the faucet in the adjacent laundry tub (thereby reducing the water supply pressure) also diminished the intensity of the whining noise. I ordered and installed this part - No. AP6023337 "Housing". The installation... Read more
Fixes washer that won't spin or agitate, hums but doesn't run, or smells like burning. This drive motor powers drum rotation for wash and spin cycles.
Replaced drive hub , drive clutch kit , & drive motor Read more
This factory screw secures panels, brackets, and other components in your appliance. Replace a missing, stripped, or corroded fastener to restore a tight fit and keep parts properly aligned and rattle-free.
In the past we’ve fixed the latch with just high speed great. This time we ordered a new latch and replaced it. Washing machine has been working perfectly ever since. It was very easy to find the right part by simply entering the model number of my washing machine. It was quick delivery and the correct part. Very happy to have a working washing machine again. Read more
Washer won't drain or clothes have residue? Replace the drain pump filter that screens debris and prevents clogs. Protects pump from damage.
On a 3 year old Maytag...........New gear case and hub installed. The videos produced by AppliancePartsPros are quite helpful, even though the video was not of the exact make and model number I was repairing, the similarities were so great that it may as well have been the same make and model number (whirlpool and Maytag essentially make the same thing and slap I different sticker on them) Read more
Suspension pad absorbs vibration and keeps your washer stable during spin cycles. Replace if machine shakes excessively or moves. Confirm fit with model.
Remove top lid panel and splatter shield. I didn't need to remove the back panel on my model. Used pliers to lift the old rod up and out. Did one rod at a time. Watched several videos so it went quickly. I've done 2 loads now and the machine has stayed in place. Be sure to balance the machine prior to that first load. I also replaced rubber pads on the interior housing. These provide bumper between the tub and housing walls. Read more
Clothes not getting clean or washplate spinning freely? Stripped plastic splines prevent agitation. DIY fix in 15 minutes—remove cap and bolt, lift out.
The plastic ridges on the inside of the washplate were stripped. New washplate solved the problem. This washer is barely 3 years old, so I guess I can expect to be doing this again, but better than buying a new washer. Read more
Extends your washer's drain hose to reach distant standpipes or sinks. Includes coupler and clamps. Replace when you need extra length for installation.
Attached drain hose extension and it more than reached the drain. Read more
Replacement internal hose for washers. Routes water or air between components. Replace if cracked, brittle, clogged, or leaking to restore proper flow.
Replacement screw for securing panels, brackets, and internal components. Replaces missing, stripped, or damaged fasteners to restore proper fit.
Replaced door latch and switch. Parts are plastic so you must know what you are doing to avoid breaking new parts. Videos were hard to find for my model - eventually I found a video that addressed a different problem but required disassembly of a washer cabinet similar to mine. I removed the control panel using a putty knife and unplugged the wire to the latch switch. Then I remove 3 screws securing the washer's top panel to the back panel. Using a rubber mallet, I gently knocked the top panel... Read more
Size: 1/4 inch hex head, 10-12 x 1/2 inch.
This trash compactor is in our vacation home. We never use it and now we are selling the house. When I looked to replace it I was amazed at how expensive a new compactor would cost. I found the serial number on the current compact entered it and your web site came up. Your schematics were excellent and made the repair very easy! Read more
Fix a washer that won't start or stops mid-cycle with a new lid strike. Restores secure lid engagement. Takes about 5-10 minutes to replace.
Ordered the part, removed the broken lid lock, replaced it with the new one. Works fine. Read more
Replacement retaining nut for washers and dryers. Secures components like pulleys, shafts, and assemblies. Order a new nut if yours is stripped or missing.
Have had this experience before. Ordered the same parts as last time plus a few more related components. Performed the repair in under an hour. All is good. Read more
Washer won't start or lid won't latch? This lid strike assembly provides the catch point for secure lid closure. Easy DIY fix in under 30 minutes.
Followed the video instructions on website. Very easy to fix. Read more
By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.