Ntw4650yqo Parts

These lid bumpers are sold individually.

The lid hinge bearing is used for the lid hinges on washers and dryers. When functioning properly, it allows the lid to open and close properly. If this is a problem with the bearing, it could make the lid difficult to move. In some cases, when the lid will not close, it means that the machine will not function correctly. Damaged lid hinge bearings should be replaced as soon as possible.The lid hinge bearings see a lot of work since they are in use whenever the lid of the washer or dryer opens and closes. They could become cracked and broken over time. Replacing the bearings is a relatively simple repair that owners can make on their own.This lid hinge bearing is for use with many models of washers and dryers from Whirlpool, KitchenAid, Roper, Estate, Inglis, Maytag, Admiral, Amana, Crosley, and Magic Chef. This is a genuine OEM replacement part that has been sourced from the manufacturer. The piece is sold individually, so if owners need to replace more than one hinge, they will need to buy multiples.

The straight-vane agitator is the finned center post that drives wash action in a top-load washer. It replaces a cracked or stripped agitator to restore proper clothes movement and consistent cleaning performance. What it does:

• Mounts on the drive shaft and oscillates to move laundry through wash water and detergent
• Restores wash action when vanes are broken or the internal splines are worn/stripped
• Helps address weak agitation, clothes not circulating, unusual rattling from a loose agitator, or visible damage
• Direct replacement for the original straight-vane agitator design

• 1 straight-vane agitator

• Disconnect power and turn off water before servicing
• Remove the center cap and hold-down bolt; lift the old agitator straight up
• Align splines, seat the new agitator, then reinstall the bolt and cap snugly
• Run a short cycle to ensure proper operation

This washer tub ring, sometimes called a tub cover, snaps onto the outer tub to contain splashing and guide water back into the basket. Replacing a cracked or loose ring helps reduce top-side leaks and protects fabrics at the tub opening. What it does:

• Forms the molded upper edge of the outer tub and acts as a splash guard
• Helps direct water back into the basket during wash and spin
• Maintains proper clearance at the tub rim to prevent fabric snags
• Common signs of failure: visible cracks/broken tabs, loose fit, or water splashing/leaking from under the lid/top

• 1 tub ring

• Disconnect power and turn off water; wear cut-resistant gloves
• Raise or open the top to access the tub opening
• Release the retaining clips/tabs and detach any connected hoses from the old ring
• Align and press the new ring evenly until all tabs fully engage; verify an even, secure fit before reassembly

This bleach dispenser for a washing machine holds liquid bleach and releases it into the tub at the appropriate point in the cycle, helping dilute bleach and protect fabrics from contact with undiluted solution. What it does:

• Holds and meters liquid bleach until the machine calls for dispensing
• Helps ensure bleach mixes with water for even, diluted distribution
• Replace if cracked, clogged, or leaking
• Common symptoms include bleach not dispensing, bleach left in the cup, leaks around the dispenser area, or bleach spots on fabrics

• 1 bleach dispenser

• Disconnect power and turn off water before servicing
• Access and mounting vary by model; follow your service manual to reach the dispenser
• Detach hoses/clamps or fasteners, transfer any reusable hardware, and seat the new dispenser fully
• Reconnect, then run a test fill/rinse to check for proper dispensing and leaks

This locking nut is used for many purposes on a range of machines including household appliances. This nut is often used for leg leveling for machines. It will help with vibrations from washers and dryers. If the nut is used for this purpose and goes missing or becomes damaged, it could cause the machine to vibrate more and seem louder.Nuts are made from metal and are built to last a long time. However, there can still be issues that arise. In some cases, the nuts might go missing if they become loose and the machine is moved. They could also corrode over time and need to be replaced. The replacement of the nut is typically a fast and simple repair.The nut is a genuine OEM replacement part sourced from the manufacturer. It can work with washers, dryers, and combo machines, and is compatible with models from Whirlpool, Kenmore, Maytag, and Roper. The part is sold individually. Owners may want to have several on hand.

This replacement screw secures panels, brackets, and other components in your appliance to keep them aligned and rattle-free. Replacing worn, stripped, or missing hardware restores a tight fit and helps maintain safe, quiet operation.

• Fastens panels, brackets, or internal parts to the cabinet/frame
• Helps maintain alignment to reduce vibration and rattling
• Replaces lost, stripped, or corroded screws
• Common symptoms: loose panels/trim, rattles, or a screw that won't tighten

• Disconnect power; shut off water or gas if applicable
• Match thread and length to the original; replace one at a time to keep alignment
• Start threads by hand to avoid cross-threading; use the correct driver
• Tighten snugly—do not overtighten, especially into plastic or thin sheet metal

This capacitor stores and releases electrical energy to give the appliance's circuit the boost and stability it needs to start and run properly. Replacing a weak or shorted capacitor can restore reliable operation and reduce strain on related components. What it does

• Provides an energy boost and stabilizes voltage in the designated start/run or power circuit
• Helps motors or power sections energize smoothly and maintain performance
• A failing capacitor may cause humming/buzzing, failure to start or heat, intermittent operation, or tripped fuse/breaker
• May show swelling or signs of overheating around the case or terminals

• 1 capacitor

• Disconnect power before service; capacitors can hold a charge—use a proper discharge procedure before handling
• Note/photograph wire locations; move leads to matching terminals and ensure tight connections
• Mount securely in the original position; re-use brackets/insulators as applicable and keep wiring clear of sharp edges or heat
• After replacement, check the related motor or circuit components if symptoms persist

This factory screw secures panels, brackets, and other components in your appliance. Replace a missing, stripped, or corroded fastener to restore a tight fit and keep parts properly aligned and rattle-free.

• Secures appliance components and panels in their mounting points
• Replaces damaged, stripped, or missing hardware
• Helps reduce rattling or vibration from loose parts

• Disconnect power; shut off water or gas supplies if applicable
• Match location with the original screw; start threads by hand to avoid cross-threading
• Tighten until snug; do not over-torque, especially into plastic or thin metal
• Reinstall any covers or panels and test for secure fit

This drain hose extension kit increases the reach of your appliance's drain line so it can connect to a farther standpipe or sink, supporting proper drainage and reducing stress on fittings that can lead to leaks. What it does:

• Extends the existing drain hose to accommodate installations where the drain connection is farther away
• Helps maintain a secure, leak-resistant connection when routed correctly
• Useful when relocating the appliance, changing cabinetry, or updating plumbing
• Common signs you may need it: hose won't reach, kinks when stretched, or occasional water near the drain line

• One drain hose extension kit

• Disconnect power and shut off the water supply; have a towel or pan ready for residual water
• Join the extension to the existing drain hose with the proper coupling/clamps; tighten securely and avoid kinks or sharp bends
• Route and support the drain line per your model's installation guide and observe any maximum total hose length
• Run a short test cycle and check all joints for leaks

This pump drain filter helps protect the appliance's drain pump by screening out debris before it enters the pump. A clean, intact filter supports proper draining and helps prevent clogs and pump damage.

• Screens debris before it reaches the drain pump
• Helps maintain proper draining performance
• May resolve issues like slow or incomplete draining, standing water, or drain-related noises
• Replacing a damaged or missing filter can reduce repeat clogs

• Unplug power and shut off water supply before service
• Access location varies by model; have towels ready for any residual water
• Note orientation of the old filter for correct placement
• After installation, check for leaks and run a brief drain cycle to verify operation

This replacement screw secures panels, brackets, and internal components within your appliance. Replacing a missing or damaged fastener restores a tight fit, reduces vibration and noise, and helps keep parts properly aligned during operation.

• Fastens panels, trim, brackets, or internal components to the chassis
• Maintains proper alignment and stability during normal use
• Replaces missing, rusted, or stripped hardware
• Common symptoms: loose or rattling panels, vibration, difficulty fastening, or a visibly missing screw

• Disconnect power; for gas appliances, also shut off the gas supply
• Match length and thread to the original; replace one-for-one in the same location
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• If the receiving hole is stripped, repair threads or replace the clip/nut before installing

Size: 1/4 inch hex head, 10-12 x 1/2 inch.

This adjustable leveling leg helps stabilize and properly level your appliance on uneven floors. Replacing a worn or missing leg reduces wobble and vibration so doors align and the unit operates smoothly.

• Screws into the base to raise or lower a corner for precise leveling
• Helps prevent rocking, vibration, and rattling during use
• Promotes even weight distribution to protect the cabinet and flooring
• Restores proper door/drawer alignment once the unit is level

• Disconnect power; shut off water supply before servicing
• Carefully pull or tip the appliance to access the leg; use a helper for safety
• Start threads by hand, then adjust height with a wrench—do not over-extend
• Verify level front-to-back and side-to-side; recheck after moving or loading

The Screw is an OEM component compatible with Whirlpool washing machines. This screw secures the rear bulkhead to the tub, ensuring vibrations are reduced through solid mounting points. Properly installed screws dampen oscillating movement.

Causes of a bad screw include damage from water exposure like corrosion or breakage from stress concentrations if the tub bangs around during imbalanced loads. 

Symptoms of a bad screw include:

• Loose or detached rear bulkhead allowing side-to-side play
• Excessive noise and shaking felt through the surrounding walls   
• Development of micro-cracks around screw holes over time
• Potential leak paths if holes are no longer sealed 

This Whirlpool replacement screw restores a stable suspension system. It is compatible with additional brands like Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This set of washer fill hoses connects your home's hot and cold water supply to the washer's inlet valves. Replacing aging hoses helps prevent leaks and ensures the washer fills properly for every cycle.

• Supplies hot and cold water from household faucets to the washer's inlet valves
• Helps address leaks, bulges, or cracks in old hoses
• Can resolve drips at fittings and water on the floor
• Improve slow or no-fill issues caused by kinks or internal blockages

• Unplug the washer and turn off both water supplies before starting
• Place a towel or pan to catch residual water; disconnect old hoses from faucets and inlet valves
• Attach new hoses to the correct hot/cold connections; tighten connections securely without overtightening
• Open valves, check for leaks at both ends, and re-tighten if needed