Pcb969sr1ss Parts

Replacement screw for securing panels, brackets, and internal components in ranges, ovens, and cooktops. Replace missing, stripped, or damaged screws.

Warming element not heating? This radiant element restores heat to your warming zone. DIY-friendly repair with basic tools in under an hour.

Fix a loose or misaligned cooktop with this maintop strike plate. Restores secure engagement between the cooktop and latch mechanism. Simple repair.

6-20 x 3/8 inch nickel screw secures trim panels, brackets, and small components in dishwashers and ovens. Replace missing or stripped screws.

Replacement mounting spacer for electric ranges. Positions and supports panels to maintain alignment and proper fit. Replaces worn, missing, or damaged spacers.

Replacement inner glass pane for oven doors. Installs inside door assembly to restore visibility and heat containment. Replaces cracked, broken, or fogged glass.

This flat washer (.250 inch inner diameter x .812 inch outer diameter) is a simple replacement part that helps distribute load from a fastener and protects mating surfaces for reliable appliance operation. What it does:

• Provides a stable bearing surface for screws, bolts or studs to reduce wear on parts
• Helps distribute clamping force to prevent pull-through or deformation of softer materials
• Reduces vibration and movement at the joint when installed correctly
• Missing or damaged washers can lead to loose fasteners, increased vibration or component misalignment

• Disconnect power and water before servicing the appliance
• Replace like-for-like: inner/outer diameters and thickness match the original washer
• Inspect mating hardware and surfaces for damage; replace corroded or deformed fasteners as needed
• Tighten fasteners evenly and avoid over-torquing to prevent washer or component damage

Replacement screw secures panels, brackets, and trim inside your oven or range. Restores tight fit when original hardware is missing, stripped, or damaged.

This side support panel replaces a damaged or missing support on the appliance's side, helping secure and align the cabinet and trim so the unit sits solidly and looks finished after installation or service. What it does:

• Provides structural support for the side of the appliance cabinet and adjacent trim
• Helps maintain correct spacing and alignment next to countertops or panels
• Replaces a bent, warped, or corroded panel
• Reduces rattles or rubbing caused by a loose side assembly

• One side support panel

• Disconnect power; turn off gas supply before servicing
• Carefully pull the unit forward for side access; support it to prevent tipping
• Remove fasteners, transfer any clips/brackets from the old panel, and reinstall with existing hardware
• Wear cut-resistant gloves and verify clearances and level before final tightening

Seals and cushions your oven door to reduce vibration and rattling. Replace when worn to restore proper spacing and eliminate air leaks. Verify fit.

Secures the oven door hinge to the range cabinet frame. Replace if cracked, bent, or damaged to restore proper door alignment and closure fit.

This drawer gasket forms the sealing edge for a refrigerator drawer to help maintain proper compartment temperature and reduce air exchange. It restores a tight seal so stored food stays fresher and the appliance runs efficiently. What it does:

• Replaces a worn or torn drawer seal that allows warm air into the drawer
• Helps reduce frost buildup, moisture, and premature spoilage of food
• Improves compartment temperature stability and cooling performance
• Prevents drafts and rattling caused by a loose or damaged gasket

• One drawer gasket

• Remove the drawer and old gasket, clean mounting channel before installing the new gasket
• Press gasket into the channel evenly; some designs clip or tuck into a retainer—avoid sharp tools that could damage the new seal
• If gasket is stiff, warm briefly with a hair dryer on low to ease installation; allow to cool and set before use
• For safety, unplug the appliance or switch off power before servicing

Replacement mounting screw for securing panels, brackets, and components inside your appliance. Needed when original screws are stripped or missing.

Hex washer head screw for electric ranges. Secures panels, brackets, and internal components. Replace if screw is stripped, missing, or damaged.