Pshss6rgxcdss Parts

The ice dispenser paddle is the front lever you press with a glass to activate ice dispensing from the freezer door. Replacing a cracked or sticking paddle restores dependable dispensing and keeps the dispenser area looking clean and finished.

• Transfers your push to the dispenser switch to start the ice dispensing cycle
• Helps ensure consistent activation when dispensing cubed or crushed ice
• Common failure signs: cracked or broken paddle, lever feels loose or sticks, must press very hard, intermittent or no ice when pressed
• Cosmetic wear at the dispenser opening

• Disconnect power to the refrigerator before servicing
• Remove the drip tray and carefully release the dispenser trim/control panel to access the paddle
• Remove mounting screws or tabs, note lever orientation, and transfer any reusable hardware from the old paddle
• Reassemble, restore power, and test dispenser operation

This replacement screw fastens refrigerator components securely, restoring a tight, rattle-free fit when original hardware is missing, stripped, or corroded. Use it to secure panels, brackets, or trim and keep parts properly aligned.

• Secures panels, brackets, covers, or trim in place
• Helps maintain correct alignment of components and hardware
• Reduces vibration and rattling caused by loose or missing screws
• Replaces lost, rusted, or stripped screws

• Unplug the refrigerator and turn off water supply if working near water components
• Match thread and length to the removed fastener; hand-start threads to avoid cross-threading
• Tighten snugly; do not overtighten into plastic or thin sheet metal
• Keep track of any spacers or washers reused from the original assembly

Keep water and ice flowing without internal filtration. This MSWF water filter bypass plug replaces the filter to seal the housing and route water properly to the dispenser and ice maker when a filter is not used.

• Installs in place of the MSWF filter to bypass filtration
• Maintains water flow to the dispenser and ice maker with no filter installed
• Helpful for troubleshooting restricted flow or when using an external filtration system
• Seals the filter head to help prevent leaks during bypass
• Note: No water is filtered while this plug is installed

• Shut off the water supply and dispense water to relieve system pressure
• Remove the MSWF filter; align and twist the bypass plug to lock into the filter head
• Restore water, check for leaks, and run the dispenser briefly to purge air
• Follow your refrigerator's instructions and use appropriate hand/eye protection

This power cord assembly supplies electrical power from the wall outlet to your refrigerator. Replace a cut, frayed, or overheated cord to restore safe, reliable operation and eliminate intermittent power loss caused by a damaged cord. What it does:

• Provides the electrical connection between the household outlet and the refrigerator's wiring
• Helps resolve no-power or intermittent power when the cord is moved
• Addresses visible damage such as cuts, cracks, fraying, or a melted/discolored plug
• Mitigates arcing, sparking, or a burning odor originating from the cord or plug area

• One power cord assembly

• Disconnect power by unplugging the unit or switching off the circuit breaker before servicing
• Pull the refrigerator forward for access; note the original cord routing and connections
• Install the new cord along the same path and secure any built-in strain relief; ensure the ground connection is properly seated
• Restore power and verify operation

This dairy compartment is the dedicated storage bin on your refrigerator's fresh food door for butter and other small items. Replacing a cracked or missing dairy bin restores secure, convenient door storage and keeps contents organized.

• Mounts on the refrigerator door to hold butter and small items
• Helps keep contents contained during normal door opening and closing
• Restores proper storage when the original bin is cracked, warped, or missing
• Addresses issues like broken tabs or a bin that won't stay attached

• Remove the old bin by lifting it up and out of the door liner channels
• Align the new bin with the door slots or hooks and press/snap into place
• If your model uses screws or retainers, transfer and reuse them
• Handle plastic tabs gently and ensure the bin is fully seated before loading

This is a grommet and it is intended for use on refrigerators and freezers. This is a genuine replacement part made by General Electric. A new grommet might be needed if the current one is visibly worn out or damaged in any way. If there are noises from vibration coming from the lower back area of the fridge there might be need for a new grommet. This is an OEM part sourced directly from the manufacturer, and it is sold individually. It is compatible with refrigerators and freezers, or units with a compressor and is made by General Electric.

This fan and pre-wired harness assembly drives airflow to the Quick Chill/CustomCool drawer so foods and beverages chill faster and hold the set temperature. Replace a noisy, non-running, or intermittent fan to restore proper drawer cooling.

• Circulates cold air into the Quick Chill/CustomCool/deli drawer for targeted cooling
• Helps correct no-chill or slow-chill performance in the drawer
• Addresses symptoms like no airflow, intermittent operation, or grinding/buzzing noises from the drawer area
• Replaces a failed fan motor or damaged wiring harness in this assembly

• Disconnect power before servicing; remove the drawer and covers to access the assembly
• Note wire routing and connector locations; transfer any original mounting hardware as needed
• Seat connectors fully and route harness away from moving parts to avoid pinching
• Restore power and verify the fan runs and airflow is present to the drawer

Front mounting grommet.

This screw fastens appliance panels, brackets, and trim so parts stay secure and aligned. Replace a missing, stripped, or rusty screw to stop rattles and restore a tight, factory fit.

• Secures covers, brackets, and trim to the appliance cabinet or liner
• Replaces missing, stripped, or corroded hardware
• Helps reduce vibration noise and loose or misaligned parts
• Maintains proper fit of guards, kickplates, or internal panels

• Disconnect power; turn off water supply if working near water lines
• Match to the original fastener to size and thread
• Start threads by hand to avoid cross-threading; tighten snugly, not excessively
• If threading into plastic, avoid overtightening to prevent damage

Size: 10-32 GXTT FLP.595 S

Keep the refrigerator's rear fan assembly secure and airflow on track with this fan orifice bracket. It supports the fan shroud/orifice so the motor and blade stay aligned, helping maintain proper cooling and reduce vibration.

• Secures the fan orifice/shroud to the machine-compartment frame
• Maintains correct fan motor and blade positioning for smooth operation
• Helps direct airflow through the condenser area for effective heat removal
• Typical symptoms of a failed bracket include rattling/buzzing from the back, a loose or wobbling fan assembly, reduced airflow, or warm temperatures

• Disconnect power and move the refrigerator to access the rear machine compartment
• Remove the rear access cover; support the fan motor/blade before loosening fasteners
• Transfer any reusable mounting hardware to the new bracket; align the orifice/shroud properly
• Ensure the fan spins freely and the assembly is secure before reinstalling the rear cover and restoring power

This air inlet cover assembly fits over the duct where cold air enters the fresh food compartment. It shields the opening and guides airflow to help maintain even cooling and reduce cold blasts directly in front of the vent. What it does:

• Covers and protects the air inlet opening between the freezer and fresh food sections
• Helps direct and diffuse cold air entering the refrigerator compartment
• Supports consistent temperatures by promoting proper airflow
• Replace if the cover is cracked, warped, missing, or won't stay secured—issues that can lead to uneven cooling or items freezing near the vent

• One air inlet cover assembly

• Disconnect power to the refrigerator before servicing
• Remove shelves/drawers as needed to access the vent on the fresh food back wall
• Remove mounting screws or release tabs to take off the old cover; transfer any reusable insulation or clips from the original if present
• Seat and secure the new cover; ensure the damper area is unobstructed before restoring power

This freezer shelf module replaces a broken or missing shelf to restore stable, level storage in the freezer. It installs in the factory side supports to help keep frozen foods organized and easy to access. What it does:

• Provides a sturdy, level surface for storing items in the freezer
• Replaces shelves that are cracked, warped, broken, or missing
• Helps prevent items from tipping or falling between levels
• Restores intended spacing and organization inside the freezer

• Disconnect power before starting
• Clear the area; let the cavity warm slightly to reduce plastic brittleness, and wear gloves—handle any glass with care
• Remove the old shelf. Align the new shelf with the side support slots/tabs and seat it fully so it sits level
• Do not force into place; ensure it's fully engaged in the supports

This Evaporator Bottom Bracket secures the lower edge of the evaporator assembly inside your refrigerator, keeping components properly aligned. Replace a cracked or missing bracket to restore a solid mount and help prevent looseness or rattling.

• Supports and stabilizes the bottom of the evaporator assembly
• Helps keep panels/components aligned to reduce vibration and noise
• Restores proper seating of the evaporator area after damage or wear
• Typical signs: broken or missing bracket, loose or rattling panel that won't stay seated

• Disconnect power before servicing; wear cut-resistant gloves
• Remove shelves/bins and the evaporator cover to access the bracket
• Reuse existing screws/fasteners; match the original bracket orientation
• After reassembly, ensure panels are fully seated and clear of the fan/coil

This replacement trim fits the dairy compartment on the refrigerator door. It restores a clean, finished look and proper fit of the butter/dairy bin so contents stay organized and the area opens and closes smoothly.

• Attaches to the front edge of the dairy/butter bin on the fresh food door to provide a finished, secure fit
• Replaces cracked, warped, or missing trim that can cause gaps, rattling, or a loose dairy compartment
• Helps keep small items from sliding out when opening/closing the door
• Built to match the original mounting points for straightforward replacement

• Disconnect power to the refrigerator before servicing
• Open the fresh food door; release tabs or remove any retaining screws to take off the old trim
• Align the new trim with the mounting points and snap in or reinstall existing hardware
• Handle plastic tabs carefully and avoid overtightening screws