Pye/G4500 Parts

(Adhesive Sold Separately).To order adhesive use part number WPY055980.This Part Can Be Used As Both The Front And Rear Seal In Some Models

The Screw is an OEM replacement part for Whirlpool appliances. The precise threads allow screws to join or assemble other parts securely. 

Causes of a bad screw can include stripping, cracking, or loss of threads due to repeated installation/removal over time. Corrosion is also possible depending on environmental conditions.

Symptoms of a bad screw include: 

• Loosened or detached components that were once fastened 
• Reduced structural integrity of connections or assemblies
• Potential safety hazards if critical parts become dislodged

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

Left side

The Screw is an OEM part for Whirlpool appliances that is responsible for securing various parts in place. The screw ensures a tight and secure fit, preventing any loose parts. A bad screw can occur due to wear and tear or accidental damage. If the screw becomes stripped, rusted, or lost, it can lead to instability or even malfunction of the affected parts.

Symptoms of a bad screw include:

• Loose or wobbly parts.
• Components not securely fastened.
• Difficulty in assembling or disassembling the appliance.
• Rattling or unusual noises during operation.

This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.

This compressor start device is the relay-and-overload assembly that helps your refrigerator's compressor start and protects it from overheating. Replacing a failing start device can stop repeated clicking and help restore consistent cooling performance.

• Provides the initial start circuit for the compressor, then disengages once running
• Protects the compressor by opening on overcurrent/overheating (overload protection)
• Helps address symptoms like: compressor won't start, repeated clicking, and warm fridge/freezer
• Often found heat-damaged or cracked when failed

• Disconnect power before servicing; access the compressor compartment at the rear
• Note wire positions; pull the old start device straight off the compressor pins
• Transfer wires to the new device; push it fully onto the compressor terminals until seated
• Reinstall the rear cover and restore power; verify normal compressor start

This articulating mullion assembly is the folding center strip for the fresh food section. It mounts to one refrigerator door and swings over the center gap to complete the door seal, helping maintain temperature and reduce condensation.

• Folds over the gap between doors to create a reliable air seal
• Helps keep cold air in and warm air out for consistent cooling
• Replaces a broken, cracked, or misaligned flipper that won't fold or latch properly
• Common symptoms: moisture or frost between doors, doors not closing/sealing, or temperature fluctuations near the door opening

• Disconnect power before servicing.
• Open the doors, remove any covers/screws securing the mullion, and note orientation for reassembly.
• Transfer any reusable trims/caps from the old mullion to the new assembly if required.
• Verify smooth folding action and full gasket contact before restoring power.

The Crossbar Pin is an OEM part for GE refrigerators. It is a small but essential component that secures the crossbar in place within the refrigerator's interior. This pin ensures that the crossbar, which supports various shelving and storage configurations, remains stable and functional.

Causes of a bad Crossbar Pin can include wear and tear over time, accidental impact or damage during loading or cleaning, or corrosion due to moisture exposure. These factors can compromise the integrity of the pin, leading to instability in the crossbar.

Symptoms of a bad Crossbar Pin include:

• Shelves or storage bins not sitting level
• Difficulty in adjusting or removing the crossbar
• Noticeable wobbling or instability in the crossbar

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

This freezer door bin support secures the door bin to the freezer door liner, keeping it level and firmly in place. Replace a cracked or missing support to restore stable storage and prevent the bin from popping off the door.

• Supports and locks the freezer door bin to the door liner
• Helps prevent bin wobble, sagging, or unexpected drops
• Replace if tabs are broken, the support is cracked, or the bin won't stay seated
• Common symptoms: bin tilts, falls off, or rattles on the door

• Unplug the refrigerator and remove items from the bin before servicing
• Lift out the door bin to access the support
• Release the old support from the liner; align and press the new support fully into place until secure
• Reinstall the bin and confirm a snug, stable fit before restocking

The Timer is an OEM part for Whirlpool dryers. It controls the electrical components and the timing of the drying cycles, ensuring clothes are dried according to the selected settings. This timer manages the duration of each cycle, turning the dryer off when the cycle is complete.

Over time, the timer can fail due to wear and tear, electrical malfunctions, or internal component damage.  

Symptoms of a bad timer include:

• The dryer not advancing through cycles
• The dryer running for an unusually long time
• The dryer not turning on or off at the appropriate times
• Irregular or incomplete drying cycles

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Refrigerator door board profile is an OEM replacement part for GE refrigerator doors. It is the electronics responsible for operating door functions like illumination, alarm systems, temperature displays, and sealed system sensors.

Causes of a bad control board can include moisture penetration corroding circuits over time, cracks or breaks from impact, or malfunctions in electronic components.

Symptoms of a bad control board include:

• Lights or displays failing to illuminate as intended
• Inability to adjust the temperature or access diagnostic controls
• Alarms or audio components malfunctioning
• Disruptions to the refrigeration cycle from sensor faults

This GE OEM replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Switch Light is an OEM part for GE refrigerators. It is designed to activate the refrigerator’s interior light when the door is opened and turn it off when the door is closed. This ensures visibility inside the refrigerator, making it easy to locate items even in low-light conditions.

Over time, the switch light can become faulty due to wear and tear, exposure to moisture, or repeated use. These factors can cause the switch to malfunction or become unresponsive.

Symptoms of a bad switch light include:

• The refrigerator light not turning on when the door is opened
• The light staying on even when the door is closed
• Flickering or dimming of the interior light
• No response from the light switch when the door is opened or closed

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

Mounts between the fresh food fan assembly and its housing to create an airtight, cushioned seal. Replacing a damaged gasket restores proper airflow and helps stabilize refrigerator temperatures while reducing vibration and noise from the fan area.

• Seals the interface between the fresh food fan and the duct/liner to prevent air leaks
• Directs airflow through the evaporator and vents for consistent cooling
• Cushions the fan mount to minimize vibration and rattling
• Failure may present as weak airflow, temperature swings, or new buzzing near the fresh food fan cover

• Disconnect power before servicing to avoid electrical shock
• Remove shelves/bins and the fresh food rear interior panel to access the fan
• Note gasket orientation; seat it evenly with no gaps and avoid stretching/compressing it
• Ensure the fan spins freely and runs quietly before reassembly

This replacement door bin fits the right-hand fresh food door and restores organized storage for condiments, jars, and small bottles. It helps maximize usable space and keeps frequently used items easy to see and reach.

• Holds condiments, small bottles, and jars on the right fresh food door
• Replaces a cracked, broken, or missing door bin
• Snaps into the molded slots on the door liner for secure storage
• Common symptoms: cracked plastic, broken tabs, won't stay seated, items tipping

• Disconnect power before servicing
• Empty and lift the old bin up and out of the door liner slots
• Align the new bin with the slots and press down until fully seated
• Confirm a secure fit before loading items

This small return spring provides the tension needed for a lever, latch, or flap mechanism in select refrigerators, helping the component move smoothly and snap back to its correct resting position after use.

• Restores proper tension so the linked mechanism operates smoothly and returns to neutral
• Helps doors, latches, or levers close or engage consistently
• Typical failure signs: weak or missing spring force, parts that don't spring back, poor closure, or rattling
• Replacing a fatigued spring can improve feel and reliability of the mechanism

• Disconnect power; turn off the water supply if working near dispenser or ice components
• Note spring orientation and take reference photos before removal
• Use needle-nose pliers and control stored tension to avoid injury
• Inspect related clips, pins, or brackets and replace if worn

Restore usable storage on your freezer door with this replacement bin. It mounts to the door to organize small items and keep them secure when opening and closing the freezer.

• Attaches to the freezer door to hold and organize frozen items
• Helps prevent items from tipping or falling when the door moves
• Replace if the bin is cracked, broken, warped, missing, or won't stay seated
• Designed to fit the specified door position on models that use this bin

• Remove the old bin by lifting up and pulling out of the door slots
• Align the new bin's tabs/hooks with the door rails and slide down until fully seated
• No tools or electrical work required; handle plastic carefully to avoid cracking
• Allow it to reach room temperature before installing

This motor pulley transfers power from the drive motor to the washer belts. The 60 Hz sizing restores the correct speed and belt tracking so the tub agitates and spins smoothly without squeal or slippage. What it does:

• Drives the belt(s) that power the washer's drive system (and on some models, the drain pump)
• Maintains the correct speed ratio for 60 Hz operation
• Worn or damaged pulley can cause belt squeal, burning rubber odor, or frayed/slipping belts
• Result in no/slow spin or agitation if the belt can't grip properly

• One motor pulley (60 Hz)

• Disconnect power before servicing; wear cut-resistant gloves
• Access the motor, relieve belt tension, and note belt routing
• Loosen the pulley set screw and remove the old pulley from the motor shaft
• Install and align the new pulley; adjust belt alignment/tension per service information, hand-rotate to check clearance, then test

• Designed for 60 Hz electrical systems; match the Hz rating to your original part