Need Help?
Call or text
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Size: 10-32
Check the power cord connection to the stove and found burned cable due to loose connection. Replaced the terminal and the nuts and installed a new power cord. Read more
Dryer won't start or respond to controls? This electronic control board manages cycle timing and user settings. Restores normal operation when failed.
Dryer won't heat or overheats? This high limit thermostat cuts power when temperatures get too high. Common fix for no-heat issues. Easy install.
When I pulled out the dryer from the wall, I could see dust/lint had accumulated everywhere and the vent system was compromised. I vacuumed up the dust/lint accumulation outside and then inside the vent system. I then opened the lower cabinet to clean and check its condition. I removed the water steamer bottle and its sub-assembly and then the drum. After cleaning and inspecting components — both visually and with a multi-meter I determined the problem was the appliance doing what it was... Read more
Supports the front of your dryer drum for smooth rotation. Replace when you hear scraping noises or the drum wobbles. Confirm fit with your model number.
First time DIY dryer repair. Videos very helpful! Remove front. Found glides worn thin, paint on drum removed where glides located. Drum, cage and motor turned easily - must be OK. Thirteen year old dryer. Order glides & felt, might as well replace belt and rollers while there. First time order - could not have been easier! Received 2nd day. Replaced parts, reassembled & connected power. Ran for 3 minutes with scraping noise then stopped with burning odor. Disassembled dryer, smelled odor from... Read more
Converting your gas dryer from natural gas to liquid propane? This LP conversion kit modifies the fuel orifice and components. Typical install: 1 hour.
The instruction u provide were exalent, the job went very well I was able to finish with in a hr. thank u for ur support. Read more
This cabinet top clip is a small plastic retainer that secures the appliance's top/cabinet to the chassis, keeping the cabinet aligned and preventing movement or rattling. It restores a flush fit between the cabinet and body. What it does:
I replaced the fill valve assembly with a new one. Had to look carefully at the parts diagrams to make sure I ordered the right one since the serial number break old vs. new didn't seem to match the number on my machine. On this particular machine you don't need to pull it out too far from the wall-leave the hoses connected to the valve, remove the screw holding the valve bracket, and pull into the washing machine where you can easily access the hose ends. A putty knife is needed to open... Read more
This rear support assembly stabilizes the appliance's rear housing and helps keep internal components aligned for smooth operation and reduced vibration. It restores proper rear-end support to prevent rubbing, noise, and uneven motion. What it does:
Replaced the roller and shaft. The roller had worn 1/4 of the way through the support shaft. Read more
This switch retainer clip secures a small appliance switch in place so the switch stays aligned and operates correctly. It helps maintain reliable switch contact for normal door or control functions. What it does:
Supports the front of the dryer drum for smooth rotation. Replace if drum is noisy, wobbling, or causes overheating. Verify fit with your model number.
New glides, idler had a crack, blower retaining ring was gone. And a good clean out. Like new again for 2 hours and $77.00 Read more
This genuine replacement screw secures appliance panels and trim so covers, consoles, and components stay firmly in place for safe, quiet operation. It replaces worn or missing fasteners to restore proper fit and reduce vibration and rattling. What it do
Replaced glass window on stove door. The hardest part was putting door back in place. You have to get the notch of hinge flush with frame before closing oven door! Read more
Felt pad.
Removed front wall of dryer, disconnected electrical from wall(first thing). Disconnect front door switch, remove tub, remove felt, clean, used compressed air to blow out all dust from heater assembly. Used compressed air to blow out all lint catch line parts. Used electrical contact cleaner to clean all electrical connections where dust and lint had gathered. Installed new felt pad by first applying high temp adhesive, let adhesive set about a minute or so, install felt. Let sit for about... Read more
Replacement idler spring for dryers. Maintains tension on the idler pulley to keep the drum belt engaged. Replace if broken, stretched, or missing.
Usually ships within 4 - 14 days
Side vent conversion kit for dryers. Includes duct, panel insert, and hardware to relocate exhaust from rear to side or bottom. Replaces missing parts.
A plumbing supply store found the part on the internet with a Whirlpool part #. I found that number on the website of another parts supplier (Appliance Zone) but it did not have a picture of the part. It was called a gas connector, and I ordered the part. It arrived quickly, but the name on the parts bag was "elbow". It was only the elbow. I couldn't believe that someone would sell half of a union. I did more searching and found your website which had a picture and description of a "Elbow Union... Read more