Shear55uc Parts

The Lower Spray Arm is an OEM part for Bosch dishwashers. It is responsible for cleaning dishes located on the lower rack through its rotating spray of water.

The lower spray arm effectively washes dishes by directly targeting them with pressurized water, helping to break up and rinse away food particles and debris. It plays an integral role in the dishwasher's cleaning performance.

Causes of a bad lower spray arm include clogging, blockages, or damage to the arm itself that prevents proper rotation.

Symptoms of a bad lower spray arm are:

• Dirty dishes on the lower rack even after a full cycle
• Dishes on the lower rack not receiving adequate water coverage
• Noticeable buildup of food residue in the lower rack and spray arm area

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

This kit replaces the sliding rails that support and guide the upper dishrack, restoring smooth, level movement so the rack doesn't bind, tip, or drop during loading and unloading.

• Guides the upper rack in and out along the tub sidewalls
• Helps correct a sticking, uneven, or hard-to-slide upper rack
• Can reduce issues like a sagging rack or difficulty engaging rack stops
• Wear from age, heavy loads, or corrosion can require replacement

• Disconnect power and shut off water before servicing
• Remove the upper rack and stops to access and swap the rails
• Transfer any hardware from the old rails
• Test rack travel and ensure stops are secure before restoring power

Restore the look and fit of your appliance's door with this outer door panel. It replaces a dented, scratched, or warped front panel, protecting the inner door assembly and helping the door close and align properly.

• Forms the visible exterior of the door assembly
• Shields and supports the inner door and attached components
• Helps keep the door's internal insulation/trim in place
• Addresses cosmetic damage and a loose or misaligned panel

• Disconnect power and shut off water before servicing.
• Support the panel while removing perimeter screws from the inner door to prevent it from dropping.
• Transfer any reusable components from the old panel, then align and secure the new panel with the original hardware.
• Verify smooth door operation and alignment before restoring power.

Hose, with o - ring, shu (uc/12 & above)

This Sump to Float Hose is an OEM part for Bosch Dishwashers. It functions to carry water from the dishwasher sump to the float assembly. Continuous water flow and exposure to detergents can lead to wear or damage over time.

What Causes a Bad Sump to Float Hose:
Exposure to chemicals and hot water, along with wear from water flow, can cause the hose to degrade or develop cracks.

Symptoms of a Bad Sump to Float Hose:

• Water leakage around the dishwasher
• Incomplete or interrupted washing cycles
• Visible cracks or damage to the hose

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

Finish the sides of your dishwasher cutout. These white side trim strips cover the left and right edges for a clean, factory look and help replace cracked, yellowed, or missing trims that leave gaps beside the appliance.

• Finishes and protects the exposed side edges of the dishwasher opening
• Conceals small gaps between the appliance and adjacent cabinetry
• Restores appearance when trims are cracked, warped, discolored, or missing
• Helps keep the unit seated neatly in the cabinet cutout

• Disconnect power at the breaker and shut off water supply before servicing a built-in dishwasher
• Remove existing trims and clean the mounting surfaces of any residue
• Align the new left/right strips correctly; dry-fit to confirm orientation and length
• Secure per your model's service instructions; verify door clearance and alignment before pushing the unit fully back

The Water Inlet Housing is an OEM component specifically designed for Bosch dishwashers. It provides the connection point for water to enter the appliance and is responsible for metering the proper amount of water into the spray arms and sump during each cycle. Working with the electronic control module, the water inlet housing facilitates precise water distribution. 

Causes of a bad water inlet housing can include mineral buildup affecting water flow, worn or damaged valve components preventing proper metering, and failure of electronic components interfacing with the housing. 

Symptoms of a bad water inlet housing include:

• Incomplete or inefficient washing  
• Abnormal noises coming from water components
• Water leaking or spraying outside of the dishwasher 
• Error codes related to water issues

This Bosch water inlet housing replacement part is compatible with some Siemens, Gaggenau, Thermador, and select Kenmore models. Replacing the housing ensures optimal water usage.

The Hinge Lever (RH) is an OEM component specifically designed for Bosch dishwashers. This right-hand lever is a part of the dishwasher door hinge assembly, working to open and close the door during each use. 

Causes of a bad hinge lever can include wear and fatigue over thousands of opening and closing cycles. Damage can also potentially occur from any impact or denting of the door surface near the lever mechanism.

Symptoms of an ineffective hinge lever include:

• The dishwasher door sagging or becoming misaligned  
• Difficulty fully opening or closing the door
• Loud squeaks or grinding noises coming from the hinges
• The door potentially detach from the hinge if broken 

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore dishwashers.

This is a button. This is a genuine OEM part made by Bosch and has been sourced directly from the manufacturer. This part is intended to replace a broken or defective button on certain different makes and models of dishwashers.This button attaches to the front panel of the dishwasher and is needed for powering on and off the dishwasher. Over time and with regular use, buttons can become worn or broken and stop working. This part requires proper tools for replacement. Before starting, disconnect the dishwasher completely from both power and water hookups. Please follow appropriate safety precautions when attempting to repair any appliances. For more accurate information on how and where to install this button, the appropriate owner's manual and included diagrams should be referred to.As an authentic replacement part, this button is suitable for use on several different models of dishwashers manufactured by Bosch, Thermador, and Gaggenau. Please note that this is a genuine part made of high-quality, durable materials and is sold individually.

This start button is the user-pressed cap on the control panel that engages the underlying switch to begin a cycle. Replace it to restore proper feel and reliable operation when the original button is cracked, loose, or missing.

• Serves as the Start control on the user interface
• Transfers your press to the control's start switch to initiate a cycle
• Helps address a broken, sticking, or missing start key
• Restores alignment and tactile feedback at the control panel

• Disconnect power to the appliance before servicing.
• Open or remove the control panel/fascia to access the button.
• Release retaining tabs/clips and remove the old button; transfer any small clips/springs from the original if present.
• Align and snap the new button into place, reassemble, and test operation.

The Cover is an OEM part for Bosch dishwashers. Designed to securely seal the sump area, this part prevents leaks and ensures that water is properly circulated and drained during the dishwashing cycle. 

Causes of failure might include physical damage such as cracks or warping, which can compromise the seal, or the buildup of debris that prevents proper seating of the cover. 

Symptoms of a failing Cover include:

• Water leaks from the bottom of the dishwasher
• Poor washing performance due to inadequate water circulation
• Unusual noises as the pump struggles to draw or expel water
• Visible damage or warping of the cover itself

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

The Sealing is an OEM replacement part for Bosch brand dishwashers. Located on the perimeter of the small rinse aid compartment door, this resilient rubber piece forms an essential water-tight seal when the dispenser is closed.   

Symptoms of a potentially problematic rinse aid door sealing include:

• Leakage or spills within the rinse aid reservoir
• Mineral deposits or residue build up inside the compartment  
• Cracks, tears, or deformation of the sealing material

Causes of a faulty rinse aid door sealing can be repetitive opening/closing stress breaking down pliability long-term. Exposure to chemical vapors from the rinse aid may also degrade sealing properties.

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.

The Hinge Lever (LH) is an OEM part for Bosch dishwashers. This left-hand lever is responsible for assisting in the opening and closing of the dishwasher door through a pivoting motion. The hinge lever works with other door components like springs and cables to provide smooth, balanced movement of the door. 

Symptoms of a bad Hinge Lever include: 

• Difficulty opening or closing the dishwasher door  
• The door not staying securely closed during the cycle
• Excessive noise or creaking coming from the door area
• Misalignment of the door 

Causes of a bad Hinge Lever can include normal wear and tear over time, damage from excessive force or weight on the door, or loose mounting hardware.

Note: Left hinge lever

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.
 

The Wire Harness is an OEM component specifically designed for select Bosch dishwashers requiring electrical connections between moving components. It facilitates signal and current pathways throughout appliance frames.

Reinforced flexing sections bend without kinks accommodating shifting door movements. While connector joints remain snug against jostling. This daisy chain design simplifies diagnostics and maintenance procedures compared to individual wiring. 

Symptoms signaling the need for a new harness include:

• Intermittent cycle malfunctions indicating loose or corroded connections  
• Broken or cracked housing exposing live conductors to shorting hazards
• Overly taut sections hindering the intended range of component motions

Causes relate to prolonged abrasion stresses and water damage compromising insulation throughout thousands of cycles. Physical damage during repairs may require a complete replacement of this integral wiring backbone.

This OEM Bosch replacement harness is also compatible with Thermador, Gaggenau, and some Kenmore dishwashers relying on consistent control schemes. Reinstallation restores reliable electrical pathways.
 

NTC (negative temperature coefficient). Resistance or capacitance decreases when temperature increases.

The Temperature Sensor with Hi Limit Thermistor is an OEM part for Bosch dishwashers. This sensor monitors internal temperatures, providing feedback to the control module during each cycle.

Causes of failure can be related to mineral buildup over time interfering with sensing or physical damage to wiring or connectors.

Symptoms of a bad temperature sensor include:

• Abnormal or inconsistent wash temperatures
• Error codes related to temperature issues
• Reduced cleaning performance from improper heating

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

The Sensor is an OEM replacement part for Bosch dishwashers. It detects soil levels through cycles, automatically adjusting water volumes and times for optimal cleaning. Precise sensing reduces overwashing.

Causes of a bad sensor involve general deterioration from continuous usage monitoring wash parameters thousands of times. Dirt or debris accumulation triggers false readings, decreasing efficiency.

Symptoms of a bad sensor include:

• Extended cycle times as improper inputs cause system delays  
• Inconsistent wash results relying on default static cycle settings
• Error codes displayed indicating disrupted functionality
• Soiled dishes from inadequate adjustments meant for heavier loads 

This OEM Bosch part maintains customized cleaning for Thermador versions as well.

The Drain Hose Adapter is an OEM component specifically designed for Bosch dishwashers. Securely attaching to the unit base, it provides the interface between the internal drain pump hose and your household plumbing. Precise sizing facilitates complete drainage.

Symptoms of a bad drain hose adapter include leaks allowing water backflow or improper drainage. Mineral buildup risks impeding water evacuation over time as well.

Causes of a bad drain hose adapter involve normal wear reducing a tight seal. Exposure to chemical or heat impacts posing warping presents replacement needs to restore function. 

Causes of a bad drain hose adapter include:

• Puddles of water remain after cycles instead of fully draining
• Mold or mildew growth forms from moisture trapped inside 
• The drain hose slides off during pumping due to a loose interface fit

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore dishwashers.