Need Help?
Call or text
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Plastic water line that connects the water inlet valve to the ice maker. Replace if cracked, leaking, or damaged. Includes installation video.
Replaced original (18 yrs.) 1/4" plastic tubing, clamp and grommet (AppliancePartsPros/GE parts) from outlet of ice maker water control valve to ice maker inlet. Also replaced water supply line to inlet of water control valve with new, GE braided, PEX 1/4" supply line with pre-attached female compression fittings on both ends. Repair job with AppliancePartsPros parts from outlet of water control valve went perfectly well, was simple, and had no leaks when tested. Parts were easy to install,... Read more
Rubber grommet seals the ice maker fill tube where it enters the refrigerator cabinet. Replace if cracked, brittle, leaking, or missing to restore seal.
Ice buildup in freezer? This defrost heater and thermostat assembly melts frost from evaporator coils. Moderate DIY repair restores proper cooling.
I replaced defrost heater with thermostat. It is a very easy and there is YouTube tutorial video for that. Read more
Compressor clicks on and off or won't start? This PTC start relay energizes the compressor start winding to restore consistent cooling. DIY-friendly repair.
I bought this relay switch and it works great. On the left side of the compressor there is a plastic cover you pry off with a screw driver. The relay switch had one wire plug on it. Just pull the wire off and the pull the relay switch off the compressor. Read more
Replaces worn or broken hinge cam riser on the lower door hinge. Restores smooth door lift and closing action. Essential when door sags or grinds.
Your "How to" video made it look simple and it was. I ordered the small part - it arrived the next day and I replaced the part in less than 15 minutes! I had a similar experience with my close dryer. You guys are great! Read more
This armature kit is the moving plunger and linkage operated by the dispenser solenoid. It opens and closes the ice chute door during dispensing and helps it seal when idle to reduce frost and warm-air leaks.
Replaced the water supply valve...boom! Read more
The recess door retainer secures the dispenser's ice chute flapper in the refrigerator door. Replacing a cracked or missing retainer restores proper flapper pivot and sealing to help reduce frost buildup and air leaks around the dispenser.
I replaced the solenoid, door, spring and bucket. The bucket cracked from ice freezing inside it. Ice froze inside the bucket because the solenoid stopped pulling the door closed which allowed hot humid air into the freezer. While I was in there I replaced the dispenser door, spring and crank because they are cheap and the old ones were moldy. The mold is most likely from the door not closing and causing condensation on the parts as well. Read more
Door solenoid with plunger.
I ordered a new solenoid and when it arrived, I installed it as follows: I cut the power to the refrigerator. I then pulled off the rubber boot (and it's plastic frame) that covers the water switch. Then I removed the bezel that covers the front of the ice maker controls by pulling it straight out. Then I removed the four screws found on the assembly under the bezel. After pulling the assembly forward a bit, I detached the multi-wire connector attached to it and put the assembly aside.... Read more
This replacement motor powers the dispenser's auger/crusher mechanism to move ice from the bucket to the chute. Replacing a weak or seized motor helps restore reliable cube or crushed-ice dispensing from the freezer door.
I watched the help videos first, then ordered the parts, and installed all items as in the video. Read more
Black. 8-18 AB HXW 3/8
I ordered the part and was impressed to receive it within two day! I didn't need the screws I ordered (which I ordered just in case) but the trim was put on with no problem and my oven looks brand new again! Thank you! Read more
Mounting screw fastens panels, brackets, and trim in refrigerators, dishwashers, and ranges. Replace missing, stripped, or rusty screws to secure parts.
Replaced the water tank. Followed the video instruction provided by Appliance Parts Pros. Very good instruction. Read more
Includes 12 retainer rings.
I ordered a replacement auger from AppliancePartsPros.com. Upon receipt of the new auger, I watched the repair video and took the ice crusher apart. I found several other parts that needed to be replaced as well. Once All the parts were received, I again watched the video. The video was not specific enough to show how to reassemble the ice crusher blades and the two types of washers. I found another video on YouTube that walked me through specific details of assembly and everything went... Read more
Secures water and drain tubing to prevent leaks, noise, and vibration. Replace if loose, cracked, or missing. Confirm fit with your model number.
This evaporator fan blade mounts on the fan motor and circulates cold air across the evaporator coils and throughout the compartments. Replacing a cracked, warped, or loose blade restores proper airflow and stable temperatures.
Ordered a new fan. Read more
Secures refrigerator wiring to prevent chafing and vibration noise. Replace when damaged or missing to keep harnesses organized. Confirm fit by model.
Mounting screw for dryer drum support and internal components. Replaces lost, stripped, or damaged screws during repairs. Package of 12 screws included.
Watched the repair video. Saw what to look for. Found the dryer drum front support was broken and the slide bearings were worn. Replaced these items. Read more