Need Help?
Call
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Fixes loose panels, rattling doors, or wobbly components caused by stripped or missing screws. Secures brackets, covers, and mounting hardware. Easy DIY.
Maytag Dishwasher (about 5 years old). Some of the buttons had stopped functioning. Then the Start button began choosing whether or not to work. Eventually it would not start at all. Upon removing the control panel, the first thing I noticed was that the brackets that hold the two lower screws were broken. (So this was the reason that the door was so hard to open from the time it was new.) I trouble shot the thermal fuse, the door-latch switches, and inspected the control board trying to find... Read more
Replacement icemaker fill tube that directs water from the valve to the ice tray. Replace if cracked, leaking, or causing water to freeze in the freezer.
Replaced the water tube that went from the plastic tubing to the ice cube tray. Found that even though it was the same exact length as the original, there was only an extremely small gap from the end of the tube to a splash board. This may have been the root cause of my problems. Read more
Seals the fresh food door to keep cold air in and moisture out. Replace when worn to restore temperature control and reduce condensation. Verify fit by model.
Loosened nuts around outer flange. Pulled out old gasket as shown in video. Prepared new gasket per included instructions. Installed new gasket again using techniques shown in video. Secured nuts then confirmed proper seal. This was not a difficult repair however patience and care is needed to ensure new gasket is properly seated without damage. Read more
Fix a refrigerator that won't cool or clicks repeatedly. This compressor start relay powers the start winding to help your compressor run. DIY repair.
After running some tests I determined that the problem was a bad defrost timer. The timer would occasionally fail to trigger the compressor to restart at the end of the defrost cycle. Since I had the unit taken apart, I replaced the termination t-stat and the compressor start relay at the same time. Parts came quick 1.5 days, job completed and the unit is up and running. Read more
1/4 inch compression nut for securing plastic water lines in refrigerators and ice makers. Replace worn, cracked, or missing nuts to prevent leaks.
Ordered part from AppliancePartsPros.com and received it 2 days later. Put the part in, fit like a glove, water and ice cube maker working flawlessly again with no leaks. Thanks. Read more
Ice not dispensing or spilling in freezer? A cracked or warped ice bucket causes jams and mess. This bin stores ice and positions it for dispensing.
We found the right ice cub bin/pan, ordered it, and it arrived quickly. Fit perfectly, and it is now catching our ice. Read more
Ice maker not making ice or water leaking? A faulty water inlet valve often causes these issues. This DIY fix takes 5-15 minutes with basic tools.
After some research on the internet,I found out that the most likely cause was a failed water inlet valve. The refrigerator is quite old so I wasn't going to spend an arm and leg on it to fix it. I was pleasantly surprised to find the part, at a reasonable price, that I needed on this website with a helpful how-to video to boot. The part I needed wasn't in stock. I was followed up with an e-mail stating an estimated time when the part would be released. A week or so later I received the... Read more
This factory screw secures appliance components to their mounting points. Replace missing, worn, or stripped hardware to restore a tight fit, proper alignment, and quieter operation across the affected assembly.
Ordered Bake Element, Y04100019 (Whirlpool AP4283614) to replace a broken bake element on my 30-year old Jenn-Air Model S125 Downdraft Slide-in electric range. Received the element very quickly but it had been damaged in shipping. Called AppliancePartsPros to report this and they quickly shipped another element - very easy process. To install the element, I turned off the power to the range, put on rubber gloves (just in case) and removed the two sheet metal crews at the rear of the oven -... Read more
Internal tubing that carries water from the supply valve to various refrigerator components like ice makers and dispensers. Replace if you notice water leaks inside the refrigerator or reduced water flow to dispensers.
Replaced the broken parts. The water leak was caused by the drain valve not directed into drain pan Read more
White plastic support post that holds up the crisper drawer cover in your refrigerator. Replace if broken, missing, or lost during moving to prevent sagging.
Removed the jerry-rigged shelf and inserted new post. Works wonderfully! Read more
Speed clip slides over panel edges to create captive threads for mounting screws. Replace worn, missing, or broken clips to restore secure attachment.
Fix water leaks in your refrigerator's ice maker or water line. This tube insert reinforces plastic tubing for leak-resistant compression fittings.
Stops refrigerator fan rattling and buzzing noise. This rubber grommet cushions the fan motor to reduce vibration. Simple DIY fix, takes under 30 minutes.
Ordered the parts from you guys, evaporator fan motor, fan blade, and new grommets. unscrewed the inside back panel of the freezer, removed the old fan, installed the new one. Read more
This replacement screw secures panels, brackets, and components inside appliances. Replacing a missing or stripped fastener restores a snug, rattle-free fit using the correct #8-18 thread and 5/8-inch length.
Replace Read more
Supports and enables smooth movement of your refrigerator cabinet. Replace if cracked, broken, or crumbled to restore stable positioning and mobility.
I contacted Appliance Parts Pros' wonderful (comprehensive and accurate) website, to search for the part. I located the part, so I ordered it and received it within 4 days, which is also an advantage of using Appliance Parts Pros. Upon arrival of the part, I had to grind off one end of the river that acts as a hub for the wheel to turn on. Then I slipped the the plastic wheel, that I received from Appliance Parts Pros, onto the rivet and welded it to the metal cage it fits onto. Finally I... Read more
Size: 1/4 inch hex head, 10-12 x 1/2 inch.
This trash compactor is in our vacation home. We never use it and now we are selling the house. When I looked to replace it I was amazed at how expensive a new compactor would cost. I found the serial number on the current compact entered it and your web site came up. Your schematics were excellent and made the repair very easy! Read more
By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.