W10282972a Parts

• Door won't open or close

Looked for parts online that were worn and compared prices. Best price was appliance part pros. Ordered and received in 2 days and easily replaced worn parts. Read more

Replaced the defrost thermostat and heater and the refrigerator was working again. Read more

The manual had instructions for pulling things apart, the flaps over the drawer tops and the clear plastic inserts in the shelf. Flaps--Easiest to work with when the shelf is out and upside down. Slide flaps to the side a little to release the axle pin on the flaps from the receptacle hole on the shelf frame. Clear plastic plates are held in with a plastic pin on the side of the shelf frame. Carefully pull the side off the shelf there away from the pin slot until the insert pops out.... Read more

I bought the listed condenser fan motor for my Maytag refrigerator. Access to the condenser fan is by removing sheet metal screws of bottom panel with 1/4 in. nut driver. Condenser fan is on left side of rear access area. Remove electrical connector by pressing-in connector release tab with thumb fingernail and pulling on connector. Remove three mounting screws with 5/16 nut driver. Work fan out to the right past the compressor. I used a pair of pliers, as a lever, behind the plastic fan blades... Read more

Ordered the new gasket from you - installed it and now my freezer is sealed i called to order the correct replacement and they were the very best at helping me !!!!! Read more

Touch up paint Read more

Replaced It With New One Read more

• Door won't close

I have a Jennair jjw9630cas double wall oven, and after a few years I noticed that the light would not go out, first in the bottom oven, and then in the top oven. After doing some research I discovered this was not uncommon, and the fix usually involved replacing the hinges and/or the hinge receptacles. It didn't look like a difficult fix so I ordered four new hinges and four new receptacles, which arrived quickly. I found a video on YouTube that showed how to replace the hinges and it... Read more

Very easy.Just set right in Read more

• Freezer not defrosting

My unit has a bottom freezer that is a drawer. I had to remove the drawer, rack, glides, glide tracks, and ice maker to remove the rear panel. This was a little difficult but after researching a few videos on line I learned some tricks that made it easier. I used a hair dryer to melt the ice. This is best done with 2 people having one at the back to sponge the water into a bowl from the pan to avoid a water mess. Using a bolt meter I checked the heating element and found it had continuity. I... Read more

There are videos on You Tube,. After removing the bottom basket, you remove the entire drawer including the door together with it, by using a screwdriver to depress the white clip on each drawer slide which releases the slide from body of the freezer. Once you pull our the entire drawer, you will need to drill out a rivet to remove the old slide. You will need a rivet gun to attach the new slide. Read more

Had to take the back cover off. It was very tight to remove the fan that sat in the drip pan but did get it off, was able to apply the same level of cursing and got the new pan installed, installing the drain tube was a breeze. Found the parts price very reasonable. Hoping the Whirlpool redesigned the pan so I won't have to do it ever again. I was surprised at how bad the quality of their original part was. Probably saved myself $150.00 on buying the part and doing it myself Read more

I found this website and was able to find the exact part we needed. It was easy as using the model number to find the right one, ordering it and placing it in the door of our fridge to replace the old broken one! Good as new! Read more

I called Sears to schedule a service call for Sat. Morning. At 11:00 a.m. A service man called and said he was going to do the service call (the original tech was going to be delayed), so he had been scheduled instead. He had another call before he could get to me (an hour drive one way And he would get lunch and see me later. I asked him about how long it might take, he said they do not charge by the hour. He said he couldn't remember for sure, but it was between $200.00 and $250.00, but... Read more

Replaced with parts ordered. Read more

First, I had to replace a cracked roller so I could roll the frig out. I did this by tilting it slightly and shoving a shim underneath. I had to use two shims to get enough clearance for the wheel. I unscrewed the old wheel, screwed in the new one pretty easy, removed the shims and rolled it out. Then I unplugged the frig from the power socket, removed 6 screws from the back panel, and pulled out the old drain kit, which had become clogged with dirt and dust. I put in the new drain kit,... Read more