Wed6600vwo Parts

This 8-18 x 5/8-inch screw secures appliance panels, brackets, and covers. Replacing a missing or stripped fastener restores a tight fit and helps prevent vibration or loosening where this exact size is specified.

• Fastens sheet-metal or plastic components where a #8-18 x 5/8 screw is called for
• Helps maintain alignment and reduce rattling or vibration
• Replaces stripped, corroded, or missing screws of the same size
• Common symptoms: loose panels, gaps/poor fit, rattling noises, or visible missing hardware

• Disconnect power and shut off gas/water (as applicable) before service
• Match thread and length to the original; replace screws one at a time to keep parts aligned
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• If the receiving threads are damaged, additional repair (clip, insert, or new nut) may be needed

This safety thermostat monitors temperature at the dryer's air inlet and opens the heater circuit if temperatures climb too high. Replacing a failed unit restores proper heat control and helps protect the dryer from overheating damage. What it does:

• Senses inlet air temperature and interrupts power to the heater when a high limit is reached
• Helps prevent overheating and repeat thermal fuse failures due to restricted airflow
• Failure symptoms include no heat, intermittent heat, very hot cabinet, or a burnt odor
• Supports consistent drying performance by maintaining safe operating temperatures

• 1 thermostat

• Disconnect power; turn off gas supply for gas models
• Thermostat is typically mounted on the inlet duct or near the heater/blower housing; refer to your model's diagram for location
• Move wires one at a time to the new thermostat; reuse existing mounting hardware
• After replacement, clean the lint path and verify proper vent airflow to prevent repeat failures

10 - 16 x 1/2

This replacement screw secures panels, brackets, and other components in your appliance to keep them aligned and rattle-free. Replacing worn, stripped, or missing hardware restores a tight fit and helps maintain safe, quiet operation.

• Fastens panels, brackets, or internal parts to the cabinet/frame
• Helps maintain alignment to reduce vibration and rattling
• Replaces lost, stripped, or corroded screws
• Common symptoms: loose panels/trim, rattles, or a screw that won't tighten

• Disconnect power; shut off water or gas if applicable
• Match thread and length to the original; replace one at a time to keep alignment
• Start threads by hand to avoid cross-threading; use the correct driver
• Tighten snugly—do not overtighten, especially into plastic or thin sheet metal

Specs: 10-16 x 1/2 inch.

This lens covers and diffuses an appliance light source, protecting it from heat, grease, and moisture while delivering even illumination. Replacing a cracked or yellowed cover restores brightness and a clean, finished look.

• Shields the bulb or LED from debris, grease, and impact
• Diffuses light for more even, glare-free illumination
• Helps maintain the appearance of the light area
• Common symptoms: cracked, broken, missing, discolored, or loose lens

• Disconnect power and let the lamp/surface cool before servicing
• Support the old lens while removing any retaining screws or clips
• Align tabs or holes carefully; seat the new lens fully and evenly
• Do not overtighten fasteners to avoid cracking the lens

This thermal cut-off (TML) is a temperature safety device that opens the circuit if overheating is detected, protecting components from heat damage. Replace a failed or tripped cut-off to restore safe, reliable operation.

• Monitors temperature at its mounting point and interrupts power at a preset limit
• Helps prevent overheating damage to components and wiring
• Typical symptoms include no power, shutting off during use, or no heat—depending on where it's installed
• Can be tested with a multimeter; an open (no continuity) reading indicates replacement is needed

• Disconnect power before servicing; some appliances (e.g., microwaves) can store dangerous high voltage—use proper discharge procedures
• Replace with the same type/rating and mount in the same location/orientation as the original
• Ensure solid contact with the sensing surface and clear airflow/venting to prevent repeat overheating
• Do not bypass thermal safety devices; verify proper operation after installation

This part is a motor clamp. This is a genuine OEM part and has been sourced directly from the manufacturer. This part is intended to replace a deteriorated, damaged, or broken motor clamp on certain makes of indoor appliance models. Motor clamps are essential for properly securing the drive motor on various types of indoor appliances such as washers, dryers, and refrigerators. Without the use of a motor clamp, the drive motor is free to move around or become detached. This can easily cause serious damage to the equipment and prevent proper functionality. Proper tools are needed to replace this part and appropriate safety measures should be adhered to when working on any type of equipment. For accurate information on how and where to install this replacement motor clamp, specific manufacturer diagrams should be referred to.As an authentic replacement part, this motor clamp can be used on multiple different models of washers, dryers, refrigerators, and washer/dryer combos manufactured by Kenmore, Maytag, Whirlpool, and Amana. Please note that this motor clamp is a genuine part made of high-quality materials and is sold individually.

This in the male piece on the front panel. For the female piece on the door order WPW10111905.

This is the stirrer motor assembly that drives the metal stirrer in the microwave's waveguide. A working stirrer helps distribute microwave energy more evenly, reducing hot and cold spots for consistent heating.

• Rotates the mode stirrer to spread RF energy inside the cavity
• Symptoms of a failing motor can include uneven heating, cold spots, buzzing or grinding from the waveguide area, or the stirrer not turning
• May restore even cooking performance when the original motor is worn or seized

• Unplug the appliance before servicing; high-voltage components in microwaves can retain a dangerous charge
• Remove the grill/cover and access panel to reach the stirrer motor location
• Transfer any mounting hardware from the original part if not supplied
• Ensure the stirrer blade or coupler is correctly seated and turns freely before reassembly

This is a refrigerator door switch. It signals the control when a door is opened or closed to turn interior lights on/off and may pause certain functions. Replacing a faulty switch restores proper lighting and door-activated operation.

• Senses door open/close to control interior lighting
• A failed switch can cause lights to stay on, never come on, or flicker
• May also affect features that depend on door status
• Common signs include no interior light or light remaining on with door closed

• Unplug power before servicing
• Access the switch at the door jamb; gently pry out the old switch
• Transfer and reconnect wiring one terminal at a time to the new switch
• Ensure the switch seats flush and test door operation before closing up

This replacement screw secures appliance panels and components so they stay tight and aligned during use. Replacing a missing or damaged screw restores a solid fit and helps eliminate rattles, loose trim, or shifting parts.

• Fastens brackets, panels, trim, or components to the appliance chassis
• Helps correct loose or missing hardware after vibration or service
• Replaces stripped, rusted, or broken screws
• Can reduce rattling noises or misaligned parts caused by missing fasteners

• Disconnect power; for gas appliances, also shut off the gas supply
• Support the part being fastened; start threads by hand to avoid cross-threading
• Use the correct driver size; tighten snugly without overtightening
• Replace hardware with the exact part number to ensure proper fit

This top hinge supports the hinged top or upper panel, allowing it to lift for service and close securely. Replacing a worn hinge restores smooth motion and proper alignment to help eliminate wobble, scraping, or gaps.

• Provides the pivot point for lifting the top/panel
• Maintains alignment and helps the top seat flat when closed
• Restores smooth opening/closing without binding or rubbing
• Common signs of failure: loose or uneven top, squeaks, difficulty lifting/closing, visible bending or cracks at the hinge

• Disconnect power; also shut off gas and allow all surfaces to cool
• Support the top/panel while removing and installing the hinge to prevent strain
• Transfer and tighten existing mounting screws unless new hardware is provided
• After installation, check alignment and clearances; replacing hinges in pairs can improve fit

This replacement screw secures appliance panels and components. Use this OEM fastener to swap out stripped, corroded, or missing hardware so assemblies stay tight, aligned, and quiet for reliable day-to-day operation.

• Provides secure attachment for panels, brackets, and internal assemblies
• Direct replacement for stripped, corroded, or lost screws
• Can help with symptoms like vibration, rattling, or loose/misaligned parts
• Supports proper fit to reduce gaps or unwanted movement

• Disconnect power; for gas or water appliances, shut off the supply before service
• Note hardware order and retain any spacers or clips from the original setup
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Repair or replace the mating part before installation

Size: 1-1/16 x 5/8 inch. Used for fill hose. For a 4 pack order 285448A

This lock secures the appliance's top panel to the front frame for a tight, stable cabinet. Replacing a worn lock restores a solid fit and helps eliminate rattles, gaps, and vibration during operation.

• Locks the top panel to the front panel to keep the top closed and secure
• Helps maintain cabinet alignment and rigidity
• Reduces movement that can cause vibration and rattling/squeaking noises
• Common symptoms: loose or popping top, visible gap at front edge, buzzing or clunking during cycles

• Disconnect power before servicing.
• Access the lock at the front edge where the top meets the front panel; remove the old lock and install the new one in the same orientation.
• Reuse original mounting hardware and ensure both sides are evenly aligned.
• Close the top and ensure a secure latch before restoring power.