Wed7300dw Parts

The Door Handle is an OEM part for Whirlpool dryers. It provides a  grip for opening and closing the dryer door, ensuring easy access to the drum.

Over time, the door handle can become worn or damaged due to frequent use, accidental impacts, or general wear and tear. If the handle breaks, it can make it difficult or impossible to open the dryer door.

Symptoms of a bad door handle include:

• The handle becoming loose or wobbly
• Visible cracks or breaks in the handle
• Difficulty in opening or closing the dryer door
• The handle detaching from the door

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

10 - 16 x 1/2

This sensor monitors humidity inside the microwave cavity so sensor-cook and reheat features can automatically adjust time and power. Replacing a failing sensor restores accurate automatic cooking and helps prevent premature shutdowns or "Sensor" error messages.

• Detects steam/humidity in the cavity during sensor-based cooking cycles
• Sends feedback to the control to optimize cook time and power levels
• Failure can cause "Sensor" errors, sensor-cook cycles that won't start or end early
• Manual timed cooking may still work while sensor-cook modes misbehave

• Disconnect power before servicing; microwaves contain a high-voltage capacitor that can retain a dangerous charge
• Access is typically behind the top grille/control area; note sensor orientation before removal
• Handle the sensor by its body; avoid contaminating the sensing face
• Route wiring as original and ensure the connector is fully seated before reassembly

Specs: 10-16 x 1/2 inch.

This lens covers and diffuses an appliance light source, protecting it from heat, grease, and moisture while delivering even illumination. Replacing a cracked or yellowed cover restores brightness and a clean, finished look.

• Shields the bulb or LED from debris, grease, and impact
• Diffuses light for more even, glare-free illumination
• Helps maintain the appearance of the light area
• Common symptoms: cracked, broken, missing, discolored, or loose lens

• Disconnect power and let the lamp/surface cool before servicing
• Support the old lens while removing any retaining screws or clips
• Align tabs or holes carefully; seat the new lens fully and evenly
• Do not overtighten fasteners to avoid cracking the lens

This flat support washer provides a stable bearing surface under a fastener. Its 1-1/2-in diameter helps distribute load, maintain spacing, and keep components aligned so hardware stays tight and assemblies operate smoothly. What it does:

• Distributes clamping force to prevent pull-through and gouging
• Maintains proper spacing and alignment between mating parts
• Helps reduce vibration, rubbing, or wobble from a loose assembly
• Replaces a cracked, deformed, or missing support washer

• One support washer

• Disconnect power and shut off water/gas before servicing.
• Note the order and orientation of any washers/spacers during disassembly.
• Inspect mating hardware and surfaces; replace any worn or damaged parts.
• Tighten fasteners to manufacturer specifications—do not over-tighten.

Includes two bumpers and two locking clips. You will use one or the other depending on hole size.

This dryer power cord connects an electric dryer to a 4-prong household outlet. Replace a worn or damaged cord to restore a safe, reliable power connection and help prevent intermittent power or overheating at the cord connection. What it does:

• Connects an electric dryer to a 4-prong receptacle for proper power and grounding
• Four-conductor design supports modern installation requirements
• Replaces cords with cracked insulation, loose prongs, or burned terminals

• 1 dryer power cord

• Disconnect power at the breaker before servicing
• Attach to the dryer terminal block per the appliance's wiring diagram and secure the strain relief

This front top panel lock secures the top to the front of the cabinet, keeping the panel closed and aligned. Replacing a worn or broken lock helps eliminate gaps and rattling for a solid, factory-tight fit.

• Holds the front edge of the top panel to the cabinet frame
• Maintains proper alignment to reduce panel movement and vibration
• Helps the top stay closed during operation
• Common symptoms: top won't stay down, visible gap at the front edge, rattling/squeaking from top area, broken or missing lock

• Disconnect power; for gas units, also shut off the gas supply
• Support the top/front panel before removing the old lock
• Remove fasteners or release tabs, note orientation, and transfer any reusable hardware
• Install the new lock and verify the top engages securely before reassembly and testing

Replace a cracked or missing bracket to keep appliance components securely mounted and aligned. Restoring this support helps prevent movement, vibration, and premature wear, so the connected part operates as intended.

• Provides a rigid mounting point for an associated component or assembly
• Maintains correct alignment and spacing within the appliance
• Helps reduce vibration, rattling, or shifting during operation
• Replaces brackets that are cracked, bent, or broken
• Common signs: loose or wobbly parts, misalignment, rattling noises, or visible bracket damage

• Disconnect power; also shut off the water supply before servicing
• Wear cut-resistant gloves—bracket edges can be sharp
• Reuse original screws/clips unless replacements are specified
• Hand-start fasteners, align parts, and tighten evenly without overtightening

This motor mount clamp secures the dryer's drive motor to its bracket, keeping the assembly aligned and stable. Replacing a worn or broken clamp helps reduce vibration, stop rattling, and prevent blower or belt alignment issues.

• Locks the motor to the mounting bracket to prevent shifting during operation
• Helps maintain alignment to minimize vibration and noise
• A bent, loose, or missing clamp can cause rattling, scraping, or thumping sounds
• Allow the blower wheel to rub or the belt to track poorly, affecting drum rotation

• Disconnect power to the appliance before servicing
• Access the motor area and release belt tension per your model's procedure
• Install the new clamp, ensuring the motor and rubber mounts/pads are fully seated in the bracket
• Blower clearance and belt alignment before reassembly and testing

This factory shield is a protective panel used within the appliance assembly. It helps guard nearby components and maintain proper operation by directing heat, air, or moisture as designed. Replacing a damaged or missing shield restores correct fit and protection.

• Provides a protective barrier for internal components in the specified area
• Helps manage airflow/heat/moisture path as engineered for the system
• Replace if cracked, warped, missing, or not securing firmly
• Typical signs include visible damage, rubbing/rattling, or evidence of heat/moisture exposure near the shield

• Disconnect power; shut off gas/water if applicable before servicing
• Access the location per your model's service information
• Transfer and reuse original clips/fasteners as needed; do not overtighten
• Verify alignment and clearances before reassembly and testing

The Dryer Drum Baffle is an OEM replacement part designed for Whirlpool dryers. The baffle, located inside the drum, helps lift and tumble clothes during the drying cycle, ensuring even and efficient drying. It agitates the clothing, allowing air to circulate freely and preventing tangling.

Note: This is the tall baffle.

Over time, the drum baffle can become loose or damaged due to frequent use and contact with clothing or objects left in pockets. Physical wear or repeated impacts might cause it to crack, detach, or warp, reducing its ability to tumble clothes properly.

Symptoms of a faulty Drum Baffle include:

• Clothes not drying evenly or efficiently
• Unusual noises coming from the drum, such as rattling or banging
• Loose or detached baffle within the drum

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This factory fastener is a #8-18 x 5/8-inch Type AB screw designed for appliance assembly. It secures panels and components to restore a tight, rattle-free fit and dependable alignment. What it does:

• Thread-forming Type AB design engages thin metal or plastic components
• Secures panels, brackets, trim, or covers to reduce looseness and vibration
• Replaces missing, stripped, or corroded fasteners
• Helps maintain alignment for proper operation and reduced noise

• One screw

• Disconnect power before servicing; shut off water supply if working near water lines
• Use the correct driver for the screw head; start by hand to avoid cross-threading
• Tighten until snug—do not overtighten to prevent stripping or cracking plastic
• Repair damaged holes or replace worn clips/inserts before installing the new screw

• Size: #8-18 x 5/8 in (length 0.625 in)
• Thread type: Type AB, thread-forming

This factory replacement nut is a threaded fastener used to secure appliance components with a mating bolt, stud, or screw. Replacing a worn or missing nut restores a tight, rattle-free fit and helps prevent loosening during operation. What it does

• Works with a bolt, stud, or screw to clamp parts together
• Maintains alignment and resists vibration-induced loosening
• Can help reduce rattling, wobbling, or minor leaks from loose connections
• Typical signs it's needed: missing nut, stripped threads, loose components, unusual vibration/noise

• 1 nut

• Disconnect power (and shut off gas/water if applicable) before servicing
• Start threads by hand to avoid cross-threading; use appropriate nut driver or wrench
• Tighten securely per service information; do not overtighten
• Inspect and replace any damaged mating hardware as needed

Size: 1-1/16 x 5/8 inch. Used for fill hose. For a 4 pack order 285448A