Wfc10soebo Parts

This controller is the appliance's electronic control board. It monitors sensors and manages cooling system operations so temperatures stay stable. Replacing a failed board can restore consistent cooling performance and responsive controls.

• Manages compressor and fan run times to maintain the set temperature; failures can cause warm temps, overcooling, or short cycling
• Coordinates automatic defrost on applicable models; faults may lead to frost buildup and restricted airflow
• Processes input from temperature sensors and user settings; issues can make controls unresponsive or erratic
• Drives status lights/alarms on applicable models; malfunctions may trigger false alarms or no indications

• Disconnect power to the appliance before servicing
• Use ESD protection; handle the board by the edges to avoid component damage
• Photograph wiring and move connectors one at a time to the new board to ensure correct placement
• Reuse original mounting hardware and ensure all connections are fully seated before restoring power

This replacement screw secures appliance components so brackets, shelves, trim, or panels stay firmly in place. Install a new screw when the original is missing, stripped, or corroded to restore a tight, rattle-free fit.

• Fastens brackets, panels, trim, or covers to the cabinet or liner
• Helps maintain alignment and reduce vibration and noise
• Direct replacement for a missing, rusted, or stripped fastener
• Use wherever your model's parts diagram specifies this screw

• Disconnect power before servicing; shut off water if working near water lines
• Match thread and length to the original location as shown in your model's parts diagram
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening (especially into plastic)
• Retain and transfer any original spacers or clips used with this fastener

The product featured is a Frigidaire refrigerator compressor. The compressor is a vital component for the cooling and freezing process of a refrigerator. A compressor works together with the evaporator in providing the cold air needed to keep everything at the desired temperature. When a compressor fails, this could have an effect that calls for an emergency repair. Losing the compressor function means the refrigerator stops getting cold in both compartments. Prolonging the repair could mean the loss of all the food items stored inside. A faulty compressor may become very loud when it operates. Users may hear a slight clicking sound on a compressor that's entirely out of commission. This is the relay clicking in an attempt to power the compressor. If a compressor does go out, keep the doors of the freezer and refrigerator shut. There's a chance the food can be salvaged if repairs take place fast enough. This compressor is a genuine OEM product and is sourced directly from the manufacturer and is only available as an individual component. Frigidaire, Kenmore, and Maytag refrigerators can be repaired with this component.

Color: Grey

This hinge assembly supports and pivots the appliance door so it opens smoothly and closes squarely against the gasket. Replacing a worn or bent hinge restores alignment and helps maintain a reliable seal and temperature performance. What it does:

• Provides the pivot point and support for the door
• Helps keep the door level for proper gasket contact
• Can help resolve door sagging, rubbing, or binding
• Can help with doors that won't fully close or pop back open
• Addresses play, squeaks, or visible hinge damage

• One hinge assembly

• Disconnect power and support the door before removing hinge fasteners
• Note and transfer any shims/spacers from the old hinge to the new one
• Reuse existing hardware unless the manufacturer specifies otherwise
• After installation, verify door alignment and full gasket contact; adjust as needed

Quantity of 1 clip.

Note: See kit# 5303922007 and 5304406520.

This 10-32 terminal block nut fastens wire lugs to the appliance's terminal studs. Replacing a missing, stripped, or corroded nut restores a tight, reliable connection and helps prevent heat damage or intermittent power at the connection.

• Secures wire lugs to a 10-32 terminal stud for a solid electrical connection
• Restores proper clamping force when the original nut is stripped, corroded, or missing
• Helps address loose/burned terminal connections, heat discoloration, or intermittent power at the block
• Suitable for terminal block and similar 10-32 stud applications on compatible appliances

• Disconnect power at the breaker or unplug the appliance before servicing
• Inspect the terminal block, studs, and wiring for heat damage; replace any damaged components
• Clean threads and start the nut by hand to avoid cross-threading; tighten firmly without overtightening
• If the stud turns while tightening, hold it with an appropriate tool to protect the block

Bottle with brush. Color: Biscuit paint. It's point-six fluid ounces.

This cooktop support rod props the range top open during cleaning or service, preventing accidental slams. Replace a bent or missing rod to keep the cooktop safely supported while you access surface components.

• Supports the lift-up cooktop in the open position
• Helps prevent the cooktop from dropping unexpectedly
• Provides safer access to burners, igniters, and valves for cleaning or repair
• Common signs of failure: top won't stay up, rod is bent, loose, or missing

• Disconnect power and shut off gas; allow the appliance to cool completely
• Lift and support the cooktop; note the rod's orientation and pivot points
• Disengage the old rod from its brackets and install the replacement securely
• The rod holds the cooktop open before closing

This temperature control knob replaces a worn or missing knob so you can easily adjust the cold-control setting. Restores smooth, precise temperature adjustments and a clean, factory look. What it does:

• Attaches to the cold-control (thermostat) shaft to change the temperature setting
• Provides secure grip and pointer alignment for accurate selections
• Typical failure symptoms: cracked or missing knob, stripped hub, or a knob that slips or won't turn the control

• 1 temperature control knob

• Disconnect power before servicing
• Pull the old knob straight off the shaft; avoid prying at an angle to prevent shaft damage
• Align the shaft shape with the new knob and press firmly until fully seated
• The pointer aligns with the control graphics after installation

This temperature control thermostat regulates cabinet temperature by cycling the cooling system on and off. It helps your appliance hold the setting you select so food stays cold without unnecessary overcooling.

• Senses internal temperature and opens/closes electrical contacts to start or stop the compressor
• Maintains the setpoint chosen with the control knob
• Symptoms of a failing control include: too warm or too cold temperatures
• Runs constantly or won't run unless tapped/adjusted
• Temperature knob has little or no effect on cooling

• Disconnect power before servicing
• Note wire locations and take photos before removal
• Route the sensing capillary/bulb exactly as original; do not kink or sharply bend it
• Secure the sensing bulb in its clips and ensure good contact; set to mid-range and allow up to 24 hours for temperatures to stabilize

This hinge assembly provides the pivot and support for your freezer door or lid, allowing smooth opening and secure closing. Replacing a worn hinge restores alignment and helps the gasket seal to keep cold air contained.

• Supports and pivots the door/lid during opening and closing
• Maintains alignment so the door/lid closes fully and seals properly
• Can help resolve sagging, binding, scraping noises, or doors not closing all the way
• Replaces a bent, cracked, or seized hinge assembly

• Disconnect power before service; wear gloves.
• Support the door or lid and use a second person to prevent drops or damage.
• Transfer any spacers, bushings, or covers from the old hinge if required.
• Align the hinge, tighten fasteners, and verify smooth operation and gasket seal.

This replacement surface burner control knob restores smooth, accurate control of your range or cooktop. Replace cracked, stripped, or missing knobs so you can reliably turn burners on/off and adjust heat to the desired setting.

• Attaches to the valve or switch shaft to power the surface burner on/off and set the heat level
• Replaces knobs that are cracked, stripped, loose, or missing
• Restores proper indexing so Off/Low/High markings align correctly
• Common symptoms include a knob that spins freely, wobbles, falls off, or won't engage the stem

• Allow all cooking surfaces to cool and turn controls off; disconnect power if servicing near internal controls
• Pull the old knob straight off the stem—avoid prying tools that could damage surrounding trim
• Align the new knob with the shaft (match the flat/D-shape) and press straight on until fully seated

This replacement terminal block cover encloses the appliance's incoming power connections. It protects the wire terminals from accidental contact and debris, restoring a safe, finished connection area when the original cover is damaged or missing. What it does:

• Covers and shields the power terminal block where the supply wires connect
• Helps prevent accidental contact with live electrical connections
• Helps keep dust and debris out of the connection area
• Common signs: missing or broken cover, cover won't stay attached, visible heat damage or discoloration on the original cover

• One terminal block cover

• Disconnect power at the breaker or unplug the appliance before servicing
• Access the terminal block per your model's service information
• Reuse existing mounting hardware; position and secure the new cover without pinching wires
• Inspect wires/terminals for heat damage or looseness and correct before reassembly

This cold control kit replaces the mechanical temperature control thermostat that regulates your refrigerator or freezer's cooling. Restore proper temperature regulation and consistent cycling when the original control sticks, drifts out of calibration, or fails intermittently.

• Senses compartment temperature with a capillary bulb and opens/closes contacts to maintain the set temperature
• Cycles the cooling system on and off for steady, reliable performance
• Common symptoms: too warm or over-cooling/freezing items, unit won't start unless the dial is moved, runs constantly, erratic temperature swings, unresponsive temperature dial
• Helps correct intermittent cooling caused by worn or pitted thermostat contacts

• Disconnect power before servicing; work in a dry area
• Access the control housing, note wire locations, and transfer wires to the new control one at a time
• Route and secure the sensing bulb/capillary exactly as original; do not kink or sharply bend it
• Set to a mid-range setting after installation and allow up to 24 hours for temperatures to stabilize

This PTC compressor start relay briefly powers the compressor's start winding to get the motor turning, then drops out as it warms. Replacing a weak relay can restore consistent compressor starts and stabilize refrigerator and freezer temperatures.

• Momentarily energizes the compressor's start winding; disengages automatically as the PTC element heats
• Helps protect the compressor by removing the start winding after startup
• Symptoms of failure can include compressor clicking but not running
• Intermittent cooling or warming temperatures between cycles
• Heat discoloration or a burnt odor around the start device

• Disconnect power and remove the rear lower access panel
• Note wire locations; remove the start device cover/retainer and pull the old relay straight off the compressor pins
• Inspect compressor pins; firmly seat the new relay and reconnect wiring
• Reinstall covers/panels, restore power, and verify normal compressor start