Need Help?
Call
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
The Timer is an OEM replacement part for GE washers. The timer controls most of the operations of the washer: water level, tub filling and emptying, length of cycles, and cycle setting sequences. Causes may involve minor power surges exposing delicate components to uncontrolled fluctuations overtime. General wear from years of activating various thermal, agitation and spin functions can degrade sensitive electronics as well. Symptoms of a bad timer include:
This GE OEM replacement part is also compatible with Hotpoint, RCA, and some Kenmore model washing machines.
Replaced the knob and timer, the lugs were stripped out on the knob and damaged on the timer Read more
This water level pressure switch monitors the tub's fill level and tells the washer when to stop filling and move to the next step. Replace it to restore accurate water levels and dependable cycle progress.
What's included: 1 pressure switch Install notes:
Purchased the switch pressure and changed the whole thing Read more
The trunnion is the hub that mounts the washer's inner tub to the drive shaft. Replacing a worn hub restores a solid, centered connection so the basket spins smoothly without wobble, slip, or grinding. What it does:
The seal at the bottom of the tub had started to fail. On large loads water would leak so I ordered a new one rubber seal. Getting the trunnion off the transmission shaft was hard as it was calcified and corroded. I used a wire brush to get some of it off and then used a lot of WD-40. The bolt holding the trunnion plate on sheared off when I tried to remove it on one side and the other came out ok (the bolt hole through the trunnion is not threaded so it should slide out once the plate is off... Read more
Fix washer overflow issues with this water level pressure switch. Monitors tub water height and signals controls to stop filling. Common DIY repair.
Ordered level switch Read more
Took out the broken one and snapped the new one in , done. Read more
Not too bad of a job You do have to remove the right side panel to access the element. Read more
Called repair man, told him it was making noise and not spinning. he told me that it was a GE and that i should put in on the curb. Opened the washer up myself and found a broken clip. Ordered the clip and it was there almost 24 hours later with standard shipping and the washer is back to normal. Read more
The Drain Hose is an OEM part for GE washing machines. It is specifically designed to channel used water out of the washer and into the household drainage system.
Causes of a bad drain hose can include physical damage from movement or installation, clogging from lint and debris, or degradation of the hose material over time, leading to leaks and inefficiency.
Symptoms of a bad Drain Hose include:
This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.
I did it Read more
This electronic control board manages key washer operations so cycles start, run, and finish as designed. Replacing a faulty board can restore proper agitation and spin performance and resolve intermittent or no-run behavior. What it does:
What's included:
Install notes:
Ordered and replaced main control switch. Easy repair, direct replacement part, basicly un-plug the old and plug in the new. Part showed up a day earlier than I had expected. Ordered with "second day" delivery and got next day service. Read more
Size: 10 fl. oz. Used on glass, ceramic and porcelain cooktops.
Quick shipping, easy repair. Read more
This genuine OEM part is a drive motor for washers. The drive motor is the main engine that drives the washer tub allowing it to rotate and wash clothes effectively. If the washer is no longer spinning or the power has significantly decreased, it might be a sign that the drive motor needs to be replaced. Luckily, replacing this part is a relatively simple repair.To replace the drive motor, start by unplugging the washer. Once unplugged, move the washer away from the wall to gain access to the back panel. Uninstall the back panel by removing the screws that attach it. After removal, locate the drive motor and proceed to unthread the mounting screws holding it to the washer. Proceed to pull the old motor out of its place and install the new motor by threading the screws that secure it. This replacement part is sold individually and is compatible with GE, RCA, and Hotpoint brand washers.
New motor. The motor was ok, but the control board mounted on the motor wasn't. Can't buy to control board separate from the motor. Easy to replace the motor, but not so easy to troubleshoot to make sure the problem was the motor and not something else. Read more
Outer tub cover that snaps over the washer's outer tub assembly. Replace if cracked, broken, or missing to restore proper clearance and protection.
I had to remove the front panel of the washing machine and top of the washing machine. i started by removing all the top screws as shown in one of videos. disconnected all the electrical wires (i have a commercial washer) and lifted the front panel over the back of the machine. i was then able to remove the top of the washing machine to give me access to the tub straps and the corresponding screws. i removed the broken straps and then was able to remove the tub cover by pushing down it down... Read more
Oil leaking from agitator or poor spin performance? This washer transmission assembly restores wash and spin cycles. Advanced repair, 2-3 hours.
Transmission seal was not available so I installed a new transmission. Works well. Thank you! Read more
The Idler Pulley is an OEM part for Frigidaire dryers. It helps guide and maintain tension on the dryer drum belt, ensuring the drum rotates smoothly during the drying cycle.
Over time, the idler pulley can wear out due to friction and regular use, or it may become damaged from excessive strain or misalignment. If the idler pulley fails, the dryer drum may not rotate properly, leading to inefficient drying or a complete inability to dry clothes.
Symptoms of a bad Idler Pulley include:
This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.
I replaced the spin bearing, tub seal, washer and drive belt since I had it all apart. The video was extremely helpful...I would have tore the whole thing apart trying to figure out how the agitator came off....but it was very simple. Read more