Wm3600hva / 01 Parts

With the video that was made from appliance pro.Help me out one hundred percent to understand what I was dealing with Read more

If you have an older model WM8000H_A you MUST pay attention to the type of door gasket (boot seal) that it uses. Every video I could find for replacing the seal on the WM8000HWA involved a different product than what was required for our specific washer. I wound up getting the wrong one by ordering it without help and had to exchange it - after I had the machine taken apart. Thanks to AppliancePartsPros I got the correct seal and front retaining ring the next day. NOTE! The retaining rings are... Read more

****** always make sure the unit is fully unplugged from the power before you do anything with the outside of the unit to work inside of the unit and while you are working inside the unit... Also make sure that you turn the hot and cold water intake valves off and make sure you don't pull too much on the two water intake hoses that lead to your washer because they can leak with too much pressure exerted on either end******* 1. Took top off unit by unscrewing mounting brackets at two similar... Read more

Bought these three products and installed them. Read more

I removed the top cover and found the left main suspension spring broken. Appliance Part Pros had the new springs (2 I replaced both) at my door in 26 hours. Excellent service from this company. After disassembling the drum from the chassis of the machine, it was very easy to replace the springs. i do wish however that I had purchased a higher quality machine. LG refused to do anything to help and the machine is only 3 years old and gets minimal use. Hats off however to Appliance Parts Pros.... Read more

My LG front load washing machine was vibrating severly on the spin cycle. I noticed the drum was tilted toward the back of the machine, so I replaced the rear damper. The repair was straightforward: just undo the back cover and swap out the damper. Using a deep socket to push the barbs on the pins holding the damper in place made the repair easier. Read more

I ordered the parts (drain pump and boot gasket) from AppliancePartsPros.com. I requested for standard shipment and it came quickly. I replaced both the drain pump and the gasket and now the washer is back up again. Read more

I opted to save myself about $600 by repairing my 8 year old LG washing machine rather than buying a new one. After watching some videos I determined what I needed upon taking my washing machine apart. I ended up replacing the tub (includes spider and shaft), since I could not get the spider part removed from the original tub, as well as the motor bolt (which had broken when I removed it from the original tub's shaft). The spider was cracked and the shaft was wobbling which caused it to... Read more

Replaced water inlet valve Read more

Removed the top cover while the machine was operating, located the source of the leak. The top filler tube had worn a hole in a flex point. Found the right part on this site, replaced it with little effort. While in there I saw a similar hose and decided to replace it as its time was probably up too. So far so good, washing clothes and no leaks!! Great prices and best of all the right parts were delivered in a timely manner. Thanks for making this so easy. Only specialty tool used was hose... Read more

If your LG Front load washers sounds like a freight train, STOP USING IT. You're doing more damage and will need more parts to fix it. After the noise became unbearable, I began to explore and disassemble. I knew enough to know the bearings must be bad but had never done this repair before. ( I am however pretty mechanically inclined.) Watch this video before you start tearing your LG apart. APP did a great job explaining the steps of the repair. Do a search on this site or youtube.com with... Read more

I figured after 10.5 years that it might be time to replace the dispenser hoses because I was noticing black stuff in the dispenser trays. I replaced two or the four hoses and clamps on the far left side and for good measure the hot water inlet valve. The inlet valve was okay but the screen had all kinds of crap in there that I couldn't clean out so now I have an extra solenoid just in case one of the others fails. While I was at it I removed the dispenser and cleaned the calcium build up on... Read more

Replaced water inlet valve Read more

Technician wanted $700. I was able to fix it myself for around $300 in about a half hour with the great and helpful customer service of appliancepartspros.com. Parts arrived on time. Nice to know there is a company that really cares and they know there stuff. Read more

I looked online ans read where the tE error code meant the thermistor was bad. I then found a video on YouTube showing how to replace the part. On AppliancePartsPros.com I chatted with a technician that told me the thermistor on my particular model was built into the heater unit and he gave me the link to purchase it. After it arrived via FedEx I followed the repair video and installed it myself (I'm a girl). So far I have run about a half dozen loads and no problems! Thank you so much... Read more