Wtw5800bco Parts

I read the FAQ section of Appliance Pros parts web site. I found out I needed to replace the temperature control switch, WPW10248240, to correct my problem. This switch also controls the tub filling water level based on air pressure via the attached vinyl tubing. I ordered the switch and the tubing, WP353255, in case mine was no longer any good, and I also ordered the retaining clips for the control cabinet, (2) of WP8312709, because they can be damaged when accessing the controls. My new... Read more

Motor control board was flashing 4 times, indicating that the mode shifter had an error. I disconnected the mode shifter's wire from the controller and measured the resistance between the 2 leads with an ohmmeter. Since the reading was infinite, that meant that the mode shifter coil or in-line thermal sensor was electrically open, i.e. bad. As this fix is near a complete tear-down of the washing machine, here are a few tips I discovered. 1) the hub nut is difficult to remove and you need a... Read more

Replaced both with ease after reviewing video. Parts matched OEM specs perfectly. ***Shipping time was excellent - placed order with standard package delivery at @11pm on a Tuesday evening & received the order in Southeast Texas Thursday morning @11am. Read more

I put all pieces that I ordered on the dryer and plugged it in. Read more

This was a tricky one to figure out. The Maytag Centennial MVWC400XW4 would fill and wash, then stop before spin cycle or would not complete the spin cycle. We had to manually move the dial to rinse & spin, etc. to get it to finish a load. This technique worked but it definitely became a pain to do and at the time we didn't notice how much longer the machine took calibrating a wash load. I called Sears initially thinking I really didn't want to mess with this and they came out. They... Read more

I ordered two replacement baffles and screws, then lifted the top of the dryer to access the drum and installed the two new baffles. Read more

I replaced the washer plate and new screw/washer part. Easy fix and back up and running in ubder 10 minutes. Read more

Bought a new one and screwed one on. Read more

On a 3 year old Maytag...........New gear case and hub installed. The videos produced by AppliancePartsPros are quite helpful, even though the video was not of the exact make and model number I was repairing, the similarities were so great that it may as well have been the same make and model number (whirlpool and Maytag essentially make the same thing and slap I different sticker on them) Read more

Attached drain hose extension and it more than reached the drain. Read more

Purchased new detergent drawer. Plug and play. Read more

Replaced door latch and switch. Parts are plastic so you must know what you are doing to avoid breaking new parts. Videos were hard to find for my model - eventually I found a video that addressed a different problem but required disassembly of a washer cabinet similar to mine. I removed the control panel using a putty knife and unplugged the wire to the latch switch. Then I remove 3 screws securing the washer's top panel to the back panel. Using a rubber mallet, I gently knocked the top panel... Read more

This trash compactor is in our vacation home. We never use it and now we are selling the house. When I looked to replace it I was amazed at how expensive a new compactor would cost. I found the serial number on the current compact entered it and your web site came up. Your schematics were excellent and made the repair very easy! Read more

Ordered the part, removed the broken lid lock, replaced it with the new one. Works fine. Read more

Springs were broken and back bracket was bent I replaced the bracket and all four Springs including the vertical one. I removed the cabinet as shown in the video. Then with a pair of vise grips's removed the springs one by one and replace them. The bracket was rusted And bent i used a quarter inch socket with a quarter inch ratchet to remove the screw. Due to the rust i used penetrating oil the screw. Read more

Have had this experience before. Ordered the same parts as last time plus a few more related components. Performed the repair in under an hour. All is good. Read more