Need Help?
Call
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Color: clear. Measures about 3 inches in diameter.
Troubleshot the oven by checking the broiler which worked good (same fuel valve). After reading the some tips about troubleshooting the Glow Ignitor I could see the broiler ignitor got white hot and the oven ignitor only got bright orange (orange to red causes intermittent ignition or mini explosions). Watched the how to video and it was good information. You should be observant about which openings in the back of the oven as to where the two wires are coming out of. My oven is over 12 years... Read more
This factory fastener secures panels, trim, or brackets on your appliance. Replacing a missing or stripped screw restores a snug, rattle-free fit and keeps components aligned for proper operation and a clean, finished appearance.
Turned off breaker,unscrewed (2 screws) element,pulled element out from back of oven,unplugged 2 wires, attached wires to new element, pushed back in, installed retaining screws Read more
Oven shuts off at high temperature or won't heat? This high-limit safety thermostat may have failed. Restores normal heating. Easy DIY fix in 30 minutes.
Thermostat was broken, was a quick easy fix thanks. Read more
This oven door hinge receptacle mounts in the cabinet frame and receives the door hinge arm. Replacing a worn receptacle restores proper door support and closure for a consistent seal and safe, reliable oven operation.
I have a Jennair jjw9630cas double wall oven, and after a few years I noticed that the light would not go out, first in the bottom oven, and then in the top oven. After doing some research I discovered this was not uncommon, and the fix usually involved replacing the hinges and/or the hinge receptacles. It didn't look like a difficult fix so I ordered four new hinges and four new receptacles, which arrived quickly. I found a video on YouTube that showed how to replace the hinges and it... Read more
To order indicator lens use WP22001948.
Factory fastener secures appliance panels, brackets, and internal components. Replace worn, stripped, or missing screws to restore tight fit and alignment.
Fixed my self Read more
Replacement oven door gasket that creates an airtight seal to prevent heat loss and improve cooking consistency. Replace if worn, cracked, or loose.
Very easy repair. 10 mins tops, removing and replacing the gasket Read more
A shoulder screw that secures appliance components and provides a precise pivot or spacer point. Replaces a missing or worn screw to restore alignment, reduce rattling, and keep panels and assemblies securely in place. What it does:
I had to remove the oven door, which I learned is made to come off without tools. Then took out the bottom by removing two screws and lifting. Removed the screws attaching the igniter, pulled wires thru back until I could get the connector and disconnect. When the new igniter arrived, I had to change the connector. I cut the one off the old one, and spliced to the new one using solder and shrink tubing. Just reverse the procedure to install. I replaced the screws with new ones. Read more
This 10-32 x 3/8 machine screw secures appliance components. It keeps panels, brackets, and trim firmly attached so everything stays aligned and quiet during operation.
Sheet metal pan head screw secures panels, brackets, and components to appliance cabinets. Replace missing, stripped, or corroded screws to restore fit.
I ordered and replaced the old ignitor and the corroded mounting screws. Read more
Hex head sheet metal screw secures appliance panels, brackets, and trim. Replace missing, stripped, or damaged screws to keep covers firmly attached.
Size: 10-32
Check the power cord connection to the stove and found burned cable due to loose connection. Replaced the terminal and the nuts and installed a new power cord. Read more
Oven won't heat or stops heating during cleaning cycle? The high-limit safety switch cuts power when temperatures exceed safe limits. Moderate DIY fix.
Started with checking temp control in the oven. Worked fine. Next was testing high limiter switch. Every place stated switch was on the back panel, found mine place under the right burner cartridge. Took some finagling to expose it. Bought a new one, two wires to disconnect along with two small screws to secure switch, slapped it in and I was in business. Oven that was out of commission for over two weeks (never buy a part from Sears, always deal with APP's!) was on the road again! Read more
Replacement 6-32 x 3/8" screw secures panels, brackets, and trim pieces on appliances. Restores proper fastening when original screws are lost or stripped.
Color: Stainless steel
I simply removed and replaced the bake element and light bulb. The only difficulty I had was working around the open oven door. I relied on the Appliance Parts Pros videos for procedures on how to do this safely and correctly. I would not have attempted this repair without the videos. The only problem I had was the $5 screws ($10 for the two I purchased) were not the same type as the original scews and they did not "grip" the oven wall properly so I had to re-use the original screws which were... Read more
By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.