Ymmh76719cs Parts

I'm a 56 year old divorced woman. I started doing these kinds of repairs to save some money and honestly, to see if I could. So yes, if I can do it, it's not that tough to do. My microwave is built in above the stove - getting it down and back up was the hardest part of the job. An extra pair of strong hands really helps-for anybody, not just a 56 year old woman. The actual repair was pretty easy. Most likely problem was pretty obvious after a little research. Easy to take off cover, get... Read more

Watched a You tube video, showed how to remove bottom, unhook wiring, then proceed to top case. Once removed, case is turned upside down so the capture nut can be installed. Part fit perfectly and BAM, done. Case refitted and finished. Part arrived in 2 days. Great service. Read more

It is difficult (if not impossible) to remove the electronic switches from the hard plastic latches. I replaced all three switches and both the upper and lower latches I also replaced the main 20 amp ceramic fuse which blew out when the latch/switches failed. Read more

I have used appliance parts pros before, their website is easy to use. I typed in the model and serial numbers, of course the number I have is rare, It did not show up on the list of models. It made me a little hesitant to submit the order. All three products came in the same box and on the same date it was promised. Just after opening the package I put everything in the microwave and I was relieved when everything fit perfectly. Read more

Very easy fix. Unplugged microwave, then lowered bottom panel, removed the two leads to the turntable motor, removed two screws attached to motor, removed old motor, put new spacer on motor stem, installed motor with same two screws, reattached the two wires, reattached panel ( after cleaning all the grease that built up over the last 6 years), plugged microwave in and good as new! Took me twenty minutes. Note: the two screws holding the motor were not Phillips like those holding the panel. So... Read more

Bought a new home with microwave venting into kitchen. Ordered damper assembly needed to vent through the wall to the outside. Removed microwave, followed directions in original installation instructions, turned fan over, cut hole in wall, installed wall cap and replaced oven. Problem solved. Read more

Ordered a new one cheaper from you than whirlpool Read more

Checked the three door switches; used ohm meter to see if there was resistance or if a switch was bad. 2 out of 3 switches showed resistance with the ohm meter. The last one tested (of course the last one) NO (normally open) did not show resistance; I.e. the ohm meter reading did not change when the switch was depressed. Appliance parts pros was the only company that had the same model number I was looking for (SZW-V16-FD-63). I ordered the relay switch, 2 days later it arrived (regular... Read more

Ordered replacement from AppliancePartsPros.com was exact fit, just snapped into place. Read more

Replacing a magnetron in my particular 9-year-old microwave (a microwave/hood combination) was not a simple “plug & play” operation. That is why I am placing this in the slightly difficult area. First, it takes 2 people to remove the microwave from the top of the stove. Next the main outer panel need to be removed. After that, 2 sheet metal panels need to be removed in order to expose the high voltage components for testing. Always discharge the high voltage capacitor first before doing... Read more

Found your site. Put in the model and serial number of what I wanted to replace. Each item had a wonderful video to show and explain exactly how to replace each part. Worked like a charm. Read more

Well, I gotta say I was happy to find you still had parts for almost 20 year old microwaves. The microwave itself worked fine, so I hated to have to buy a new one, but I just couldn't take being hit in the head anymore; and my fix of using string and wire to tie it to the surrounding cabinets was unsightly to say the least. I'm glad I did some research and found this part - all I had to do was pop it in place and now the vent grill is secure. Problem solved with minimal cost. Read more

I attempted to diagnose the four thermostats/thermal switches in the microwave....two right behind the control panel, one on top of the cooking cabin, and one under a metal shroud above the magnetron. While checking continuity with a voltmeter, i questioned one of them behind the control panel and the one above the magnetron. I then noticed a burn mark on the plastic connector sleeve for the one above the magnetron. I took a scrap piece of 14 gage copper wire and beat the ends flat with a... Read more

Checked switch with a voltmeter, determined the switch was bad. Ordered a new switch....watched a short how to you-tube video.....and from there.....it was fixed. Read more

It is difficult (if not impossible) to remove the electronic switches from the hard plastic latches. I replaced all three switches and both the upper and lower latches I also replaced the main 20 amp ceramic fuse which blew out when the latch/switches failed. Read more

Obtained the replacement motor and tray coupler from Appliance Parts Pro. Video of the typical replacement was very helpful to show what to expect and how to replace the motor and coupler. The removal of the bottom plate was held in place by several phillips screws. The motor was attached with two torx screws. The electric connection clips to the motor required needle nose pliers to pull them off. The tray coupler was simple to install after the motor was secured and bottom plate was replaced.. Read more