Need Help?
Call or text
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Refrigerator not cooling? Compressor won't start? This inverter board controls compressor speed and cooling. Moderate DIY repair with electrical testing.
Took out the old part and replaced it with the new part. Now all is working. Thank you so much. Read more
Restores proper door seal and replaces identification label on side-by-side refrigerators. Replace if door won't seal, gasket is hard or torn. Confirm fit.
Fix a refrigerator that won't cool or has freezing issues. This main control board regulates temperature and system cycles. Moderate DIY repair.
This was a newer GE Monogram side-by-side unit that used an inverter compressor. I removed the inverter and used an ohmmeter to measure the resistance of each of the three windings. They were all very close to one another: about 6.8 ohms per winding. I concluded that the compressor was probably not at fault. The inverter kind of burned or chemical-ish, and, when opened, showed an electrolytic capacitor had burst. I replaced the inverter with an overnight part from Amazon. It was the same... Read more
Fix a refrigerator that won't cool or has temperature issues. This main control board manages cooling cycles, fans, and compressor operation. Moderate DIY.
Replaced the Main Control Board Assembly along with the evaporator and condenser fan motors. I thoroughly cleaned the very very dirty condenser with a 4$ brush offered by the parts specialist and while I was at it, I changed the door seals and replaced one of the door trays. Beats the crap out of spending $10,000 on a new refrigerator that because of Covid 19 wouldn't be here before the middle of November. Thank you Matt for your help! Read more
The Spring Closure is an OEM part for GE refrigerators. This spring aids in the automatic closing of the refrigerator door, ensuring it seals tightly after each use to maintain optimal internal temperatures.
Causes of a bad spring closure can include regular wear and tear, corrosion due to moisture, or accidental damage that compromises its function.
Symptoms of a bad spring closure include:
This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.
1) Remove toe kick panel - 2 Philips head screws 2) Lay down on floor. This might be the hardest part of the repair from some people! 3) Remove broken spring, no tool required. 4) Using your fingers, slip one end of new spring into hole on lever arm. (If you're not sure how it should go, look at the spring on the other door, assuming you have a side-by-side.) 5) Hook the other end of the spring around a round-shank screwdriver. (Don't even bother with pliers. You will disregard this advice... Read more
Replacement gallon door bin for refrigerator. Holds large containers like gallon jugs in the door. Order if your bin is cracked, broken, or missing.
Replaced bin Read more
Seals your refrigerator's fresh food door to prevent warm air leaks and maintain temperature. Replace if torn, cracked, or loose. Verify fit with model.
Found model number of refrigerator and input into search which brought me to parts diagram of refrigerator. From there it was easy to find the correct part numbers and also decided to change the door springs. You guys made it easy to find the correct parts and the express shipping arrived on the promised day. The installation videos were also helpful and now my 2003 refrigerator runs good as new. I will let all my friends and relatives know what a great site you have and what great service you... Read more
This halogen light bulb restores bright, reliable illumination inside your appliance, making it easier to check food and read controls. Replace a burned-out or broken lamp to bring back safe, convenient visibility while cooking.
Had to remove all three food drawers and the back panel behind the drawers (4 screws). The water tank comes with the associated tubing which would typically require access to the back of the fridge to run the new lines. Instead I clipped the existing lines inside the fridge. Then I clipped the lines off the new tank so they would line up with the old lines. I then used a 5/16" OD compression coupling (Lowes or Home Depot) to connect the ends of the tubing together. The joined tubes are... Read more
Fix food freezing or warm spots in your fridge with a new air damper assembly. Controls airflow between compartments. Moderate DIY repair, 1-2 hours.
It started with clicking sounds for about 10 seconds at random times throughout the day. eventually the clicking sounds were gone and the temperature in the fresh food section was dropping below freezing. Turns out that one of the 3 damper doors was stuck open. My fridge has a damper door in the top left and 2 doors in the bottom left. One of the bottom doors was dedicated to the quick chill drawer which hadn't worked in some time. but since the quick chill door was stuck closed it did not... Read more
Fix refrigerator lights that won't turn on when you open the door. This light door switch activates interior lighting. DIY repair in under 30 minutes.
I tested the conductivity across the door switch and found the switch had failed. Read more
Fix a refrigerator that won't cool, beeps constantly, or has no power to the compressor by replacing the main control board. Moderate DIY repair.
EVERY THING WORKS, PUT IN NEW CONTROL BOARD AND WATER VALVE. VERY PLEASED. Read more
This evaporator fan motor dust cap is an authentic OEM replacement part found on refrigerator and freezer fan motors. This dust cap prevents the fan motor bearing and housing from being damaged by dirt and debris. If the dust cap is cracked or broken, the fan may make loud squealing noises. If the dust cap is not removed and replaced, the fan could stop working and ultimately cause the refrigerator's temperature to be affected. To start, disconnect the power and water to the refrigerator. Remove food from the freezer so that the back panel of the freezer can be accessed to reach the fan. Remove the ice maker and set it outside the freezer. Disconnect the fan and take it out of the freezer to expose the fan's shaft and the dust cover. Pry the dust cover off and install the new one. Replace the fan and cover. Reconnect the wires and reinstall the icemaker. Put the food back in the freezer. Reconnect the power and water.The evaporator fan motor dust cap is a white plastic part that is sold individually. This dust cover is made for use in refrigerators manufactured by General Electric, Hotpoint, and Kenmore.
Replacement of the evaporator fan motor, fan blade, and grommets. The amount of disassembly to reach the part took most of the effort Read more
Fix no ice or hollow ice cubes by replacing the ice maker assembly. Common 15-minute DIY repair for refrigerators that stop producing ice properly.
Replaced ice maker. Read more
Replace your worn refrigerator door gasket to restore an airtight seal, maintain consistent cooling, and reduce frost buildup. Verify fit with your model.
Magnetic door gasket seals the refrigerator compartment to maintain temperature and reduce energy loss. Replace when worn, cracked, or loose. Confirm fit by model.
Removed and replace seals. Service video has you removing the doors. I found this to be unnecessary. Read more
Protective grille cover that mounts over the temperature sensor in your refrigerator. Replace if cracked, broken, or missing to properly shield the sensor.
Common theme on the blogs was thermistors and or defrost heater/thermostat. Ran self-diagnostics which turned on defrost heater which was fine. All five thermistors indicated ok on diagnostic also, but I read more than one time "replace the thermistors no matter what if your FF section isn't cooling". So I ordered all five thermistors and defrost limiter thermostat. Received all in 48 hours (great shipping service), took me about three hours to replace all thermistors and thermostat just as... Read more