Need Help?
Call
The Igniter Sensor is an OEM part for LG dryers. This sensor plays a critical role in the ignition process, ensuring that the gas ignites properly to produce the heat necessary for drying clothes efficiently. It helps monitor and regulate the ignition temperature.
Over time, the igniter sensor can become faulty due to regular use, exposure to high temperatures, or electrical issues. These factors can lead to a malfunction, resulting in the dryer not heating properly or failing to start.
Symptoms of a bad igniter sensor include:
This OEM LG part is also compatible with Sears/Kenmore.
Used video and took apart dru, this was extremely helpful. I bypassed the belt and door switch. Tested gas valves (gas disconnected) with multimeter. Found that the igniter worked the first gas valve, but the second gas valve would not open and the igniter would stay on. Found a flow chart online that shows the flame detect turns on causing the gas to turn on and shuts off the igniter. I replaced it and tested again. Igniter turns on, shuts off, then power to the second gas valve turns... Read more
The Moisture Sensor is an OEM part for Whirlpool dryers. This part detects the moisture level in the clothing during the drying cycle, allowing the dryer to adjust the drying time accordingly.
Causes of a bad moisture sensor can include regular wear and tear, buildup of lint or residue, or physical damage.
Symptoms of a bad moisture sensor include:
This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.
Viewed the video before I purchased the part. Received the part and put it in. Everything went as planned. Read more
Fix erratic oven temperatures or F2 error codes with this temperature sensor. Monitors and regulates heat levels for accurate cooking. Moderate DIY repair.
Replaced the sensor at the back of the oven. Read more
Dryer runs but won't heat? A blown thermal fuse is the most common cause. This overheating safety device protects your dryer's heating system. DIY repair.
Removed the heater of course and installed the part. Very easy to do no need to remove the drum, just top cover, control panel, and front door assembly. Remove the one screw holding heater, remove blue wire, turn heater CCW to the 8 o'clock poisiton. Install in the reverse order. This is the secound one in a month if it fails again i'll just bypass it and install a 25 AMP fuse. Read more
The Rotor Position Sensor is an OEM part for LG washing machines. This sensor monitors the speed and direction that the washing machine tub is spinning. It ensures the tub rotates properly in both clockwise and counterclockwise motions during cycles.
Causes of a bad rotor position sensor can include wear and tear from extended use agitating heavy loads, breakage from impact or moisture damage, or compromised wiring over time.
Symptoms of a bad rotor position sensor include:
This OEM LG part is also compatible with some Kenmore models.
I was having trouble with my Kenmore Front Load washer. It wouldn't finish the wash cycle...it kept displaying an LE Error code. After I went to Google to help diagnose the problem, which was a bad RPS Sensor, I ordered the part from AppliancePartsPros.com. It literally took about 15-20 mins and with the help of my son-in-law, my washing machine was fixed!! It was going to cost me $85.00 for the Sears repairman to walk in my door, not including parts and labor, and I only paid $27.00... Read more
The Thermostat is an OEM component specifically designed for GE laundry machines. It is a heat-sensing component that monitors and regulates air temperatures inside the dryer drum. Precise thermostat functioning ensures proper drying temperatures are reached and maintained for optimal performance.
Symptoms of a bad thermostat include:
Causes include sensor degradation, electrical faults, or improper ventilation reducing its ability to accurately measure temperatures.
This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.
Realizing that there could be multiple reasons for a gas dryer failing to heat, I decided to test everything I could. The very detailed and product specific video showed me how to disassemble the dryer. The thermostat, cycling thermostat, high limit, flame detector, igniter, gas valve coils and timer all showed correct continuity or resistance. I thought it might be the gas valve itself, but felt that wasn't likely so I decided to go ahead and replace the thermostats and limit switch since... Read more
The Cycling Thermostat is an OEM part for Whirlpool dryers. This thermostat regulates the temperature inside the dryer by cycling the heating element on and off to maintain a consistent temperature. .
Causes of a bad cycling thermostat can include wear and tear over time, electrical faults, or damage due to overheating.
Symptoms of a bad Cycling Thermostat include:
I removed the front panel and observed the heating element while running the dryer. It was cycling off every minute or so and staying off for several minutes. Even though it was likely the high temp cycling thermostat I replaced both the 14, and 15 cycling thermostats which I think are the original factory units. That makes them nearly 35 years old. Problem fixed. Read more
Dryer not drying evenly or shutting off too soon? A faulty outlet thermistor causes inaccurate heat control. This sensor monitors exhaust temperature.
Fix excessive frost buildup in your freezer with a new defrost thermostat. This sensor regulates defrost cycles to prevent ice on coils. DIY repair in 10-20 minutes.
This is a 15 yr old Kenmore (GE) refrigerator with top mounted freezer... I knew, for awhile, that I had a DEFROST problem. That was causing water to collect on the inside bottom of the fridge, under the veg./fruit bins. And then occasionally run out onto the kitchen floor if I didn't sop up the water inside. But I delayed the repair because of the hassle of emptying the food, top and bottom, and finding temporary homes for it all. Until I noticed 3 things happen in short order. 1)The water... Read more
Oven won't heat or shuts off after reaching temperature? The hi-limit thermal switch prevents overheating. DIY repair takes 30-60 minutes.
Replaced the hi-limit switch and oven control. Read more
This replacement part is a high-limit thermostat, and it is intended for use in different types of appliances. This is a genuine replacement part made by General Electric. This high-limit thermostat is typically found in dryers and controls the heat inside the drying tub. This is especially important as different dryer settings require different amounts of heat. If the high limit thermostat works properly, the temperature inside the tub should reach the correct amount during each drying cycle with no issues. A new high-limit thermostat might be needed if the user notices that the dryer is unable to reach the appropriate level of heat for a certain drying cycle. This is also true if the dryer is becoming too hot when the heat is supposed to be set to low. Make sure the dryer is cooled down prior to replacing this part as the areas in the back of the dryer can become very hot during use. Be sure to reference the specific user manual for more instructions on how to replace the thermostat. This thermostat is sold individually and is a genuine OEM part. The thermostat is sourced directly from the manufacturer.
Replaced thermal stats Read more
Fixes warm fridge with cold freezer caused by frosted evaporator coils. This defrost thermostat regulates defrost cycles. Moderate DIY repair, 1-2 hours.
Well at first I thought the defroster element was the problem,so I was removing it to ohm it out and it broke upon removal.After replacing the element I was hoping that was the problem...After a week or so started having same problem with evap. freezing over.So I came back to your site to research what else could be the problem,and low and behold found an article about the defroster thermostat and a video on how to replace it.Ordered the thermostat and it was here within 2 days,replaced the... Read more
Oven won't heat or has no power after self-clean? A blown thermal fuse is likely the cause. This safety part cuts power if temps get too high.
This is for the Whirlpool in-wall double oven GBD307PDS10. No power and the door locked after the shutdown before the self-cleaning cycle was over. I watched some video and this is a known issue the fuses blow during self-cleaning. I opened the door with a 90-degree hook, an easy task. Took doors off (watch video from others), unscrewed from the wall, and made a very small platform. and took the oven out (need two people and take the doors off first. The doors are heavy and you won't lift the... Read more
Dryer won't heat or stops heating? This high limit thermostat monitors heater housing temperature and cuts power if it overheats. Easy DIY fix.
Washing machine should have been an easy fix that I had done before but ran into problems with the upper bearing and the bearing diameter on the shaft (a no go situation). By the time I was able to get the bearing seated I had damaged the new bearing. Much to my surprise Cierra in customer service sent me out a new bearing kit. I was then able to get the washer up and running with the new bearing kit and motor stator replacement. The dryer was a matter of replacing all of the electrical... Read more
Fix a dryer that won't heat properly or overheats with this thermostat. Senses exhaust temperature to regulate heat cycles and prevent damage.
This cycling thermostat regulates exhaust temperature by switching the heater on and off to maintain proper drying heat. Replacing a failed thermostat restores consistent temperatures, helps auto-dry timing, and protects against fabric-damaging overheating.
I went ahead and ordered the element, and the 2 different thermostats not knowing exactly which one might be the problem. My My Maytag opens from the front and it was actually pretty easy to get into. Also gave me the opportunity to vacuum out the inside of the dryer. Pop the top off, remove the wires that connect the door switch (noting the colors and placement), take off the 2 inside nuts that hols the fron on, pull it forward and lift it off, 3 inside screws to take out to inside lint part... Read more
By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.