Power Strike Small Engine Regular Starter Parts
Genuine Whirlpool part
By: Whirlpool
Part Number: WP3391914
Dryer won't heat or overheats? The high limit thermostat monitors drum temperature. Moderate DIY repair with heater housing access required.
Do-It-Yourself Stories from Customers like You
My whirlpool dryer was not getting hot Anthony D. • Sanibel , FL • May 01, 2016
I purchased a new heating element. Very easy to fix in about twenty minutes
Read more
More
$81.36
- Compare At:
-
$96.00
- You Save:
-
$14.64
Genuine Samsung part
By: Samsung
Part Number: DC47-00017A
Dryer won't heat or stops heating mid-cycle? The high limit thermostat cuts power when temperatures spike. Easy 15-minute fix with video guide.
Do-It-Yourself Stories from Customers like You
My dryer would not heat up Chris R. • Glen Saint Mary , FL • January 07, 2015
When starting my dryer the motor would power up and rotoe the drum and blower. Afetr about 20-30 seconds the igniter would come on then the gas valve would open and I would get heat for about 6 or 7 seconds then it would shut off. I know the burner is suppoed to cycle on and off but once the burner shut off it would not come bqack on unless I shut the dryer off and then back on. I checked for continuity on the thermistor, the thermal fuse and the high temp sensor. All three of them appeared to...
Read more
More
$82.47
- Compare At:
-
$98.14
- You Save:
-
$15.67
Genuine Whirlpool part
By: Whirlpool
Part Number: WPW10467289
The Water Temperature Sensor is an OEM part for Whirlpool washing machines. This sensor ensures the water is reaching the proper temperature at each stage of the wash cycle. Note: The sensor does not include the seal W11590578. Order separately if needed.
Causes of a bad temperature sensor can be failures over time due to mechanical wear, thermal stress on electronic components, or damage from leaks/flooding inside the unit.
Symptoms of a bad water temperature sensor include:
- Inability to switch between wash steps or advance through the cycle
- Erratic or inconsistent temperature readings
- Failure alarms or error codes displayed
- Improper or incomplete washing even on high heat settings
This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
Do-It-Yourself Stories from Customers like You
F2 e3 error code on front load duet washer Mark M. • Saratoga Springs , NY • September 16, 2016
Replace the water temperature sensor and still had the error code. While I had the back of the machine open I ran the washer. I traced the black wires from the temperature sensor and wiggled them as the washer was running. At one zip tie every time i moved the wires the washer would stop running and the error code would flash. Sure enough, like many others posted, the vibration from the machine had split the wire. I spiced the wire back together and have not had a problem since.
Read more
More
$34.75
- Compare At:
-
$41.70
- You Save:
-
$6.95
Genuine Ge part
By: Ge
Part Number: WB14X41386
Oven door won't close or lock properly? This range door latch and handle assembly secures the door during baking and self-clean cycles. DIY repair.
Do-It-Yourself Stories from Customers like You
Oven door lock quick working Jerry C. • Virginia Beach , VA • February 17, 2020
Replaced the part.
Read more
More
$58.25
- Compare At:
-
$69.32
- You Save:
-
$11.07
Genuine Frigidaire part
By: Frigidaire
Part Number: 137539200
Dryer won't heat or shows E66 error? The thermal limiter prevents overheating by monitoring airflow. Moderate DIY repair, requires rear panel access.
Do-It-Yourself Stories from Customers like You
Frigidaire dryer error e66 then door open Nolan R. • Hoboken , NJ • February 06, 2017
My Electrolux Frigidaire Gas Dryer stopped working and I got an error code E66 that the thermal limiter blew from over heating. The E66 code stops displaying after the initial code and you will then get a door open message. I replaced the thermal limiter and the thermostat just to be sure which part at the problem. The job is hard because you have to take apart the entire dryer and remove the drum. Would be a tough project to complete on your own.
Read more
More
$37.55
- Compare At:
-
$45.06
- You Save:
-
$7.51
Genuine Whirlpool part
By: Whirlpool
Part Number: WP3406108
The Door Switch is an OEM part for Whirlpool dryers. It is responsible for detecting whether the dryer door is open or closed. When the door is closed, the switch allows the dryer to operate. Conversely, if the door is open, the switch interrupts the electrical circuit to prevent the dryer from running, ensuring safety during use.
You should replace the door switch if it becomes faulty. Causes of a bad door switch can include wear and tear from regular use, electrical failures, or physical damage from repeated opening and closing of the dryer door. A malfunctioning door switch can prevent the dryer from starting or cause it to stop mid-cycle.
Symptoms of a bad door switch include:
- The dryer not starting or responding when the door is closed
- The dryer stopping mid-cycle without reopening the door
- The dryer continuing to run when the door is opened
- Error codes related to the door switch or door lock mechanism
This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
Do-It-Yourself Stories from Customers like You
Broken door switch and lint filter cover Christopher W. • Collierville , TN • December 14, 2014
Plug and play minus a few screws to remove, simple repair.
Read more
More
$35.95
- Compare At:
-
$42.78
- You Save:
-
$6.83
Genuine Whirlpool part
By: Whirlpool
Part Number: WP8181651
Fix DL error codes and doors that won't stay shut with this washer door strike. Works with the door lock assembly. Easy 30-minute DIY repair with video.
This part fixes the following symptoms
-
Lid or door will not open
-
Lid or door won't close
-
Won't start
See more...
Do-It-Yourself Stories from Customers like You
Drum spider support broken Debbie E. • Elizabethton , TN • February 14, 2015
New inner drum and front and rear outer drum; although other parts worked, still replaced the bellow and clamp, new door latch, and cleaned the hoses. Washer works great. Just like brand new. Even though matching dryer works, I am going to clean it up and replace some parts on it also.
Read more
More
$18.95
- Compare At:
-
$22.55
- You Save:
-
$3.60
Genuine Ge part
By: Ge
Part Number: WR07X10084
Fridge clicking but not cooling? A faulty compressor start relay prevents startup. This part restores cooling in 15-20 minutes. Includes installation video.
Do-It-Yourself Stories from Customers like You
We had no power only lights on Frank A. • Smithtown , NY • January 28, 2022
GE refrigerator 12 years old and we love it. Ordered compressor overload and compressor start relay video's were great made the replacement easy. I also ordered the control board because I felt this was the real culprit again the video was the best. With all the parts replaced GE profile refrigerator has been working like new. Thank you AppliancePartsPro.com
Read more
More
$82.95
- Compare At:
-
$97.88
- You Save:
-
$14.93
Genuine Whirlpool part
By: Whirlpool
Part Number: WP307473
Dryer won't start or heat? A blown thermal fuse cuts all power to protect against overheating. Easy 30-minute DIY fix with multimeter testing.
Do-It-Yourself Stories from Customers like You
Catastrophic failure of the dryer cycling thermostat in a maytag neptune super stack Richard M. • Cornish , NH • October 19, 2020
Through 15 years of vibration, the Cycling Thermostat evidently had degraded to the point where one electrical connection or more came loose and caused a short. There is also a possibility that the Bakelite section of the Dryer Cycling Thermostat body separated from the metal base, simultaneously exposing all four connections to a short. The thermostat literally exploded into chunks and dust. There was a heavy arcing and then, thankfully, the thermal fuse blew and shut down power to the short...
Read more
More
$53.21
- Compare At:
-
$62.79
- You Save:
-
$9.58
Genuine Whirlpool part
By: Whirlpool
Part Number: W11188327
Fix a washer that won't start or spin due to lid lock failure. This lid lock assembly prevents opening during cycles. DIY repair in about 45 minutes.
Do-It-Yourself Stories from Customers like You
Shut off. No water. Lid did not lock. Francis H. • Lutts , TN • February 14, 2021
Replaced lid switch
Read more
More
$108.40
- Compare At:
-
$127.91
- You Save:
-
$19.51
Genuine Bosch part
By: Bosch
Part Number: 00612148
Washer won't start or door won't lock? This door lock assembly secures the door during cycles. DIY-friendly repair, typically takes 15-30 minutes.
Do-It-Yourself Stories from Customers like You
Washer lock broken Arun P. • Burbank , CA • November 14, 2015
Disconnect existing part and connect new one. Disconnect involved removing back cover around lock and electrical connector. Also had to remove rubber gasket.
Read more
More
$105.52
- Compare At:
-
$125.57
- You Save:
-
$20.05
Genuine Frigidaire part
By: Frigidaire
Part Number: 134786100
This moisture sensor consists of two metal strips typically mounted inside the dryer drum area that detect the moisture level in clothing during a drying cycle. It signals the control board to end the cycle when clothes reach the desired dryness. Replace this sensor if your dryer shuts off too early with clothes still damp, runs too long, or if the auto-dry cycle no longer functions properly.
Do-It-Yourself Stories from Customers like You
The sensor-moisture clip was broken off and needed to be replaced. Edgar D. • Bradford , AR • April 06, 2014
Simple unscrewed the set screw, removed the broken sensor-moisture part, attached the leads, and reattached the part to the back of the dryer. Took about 4 minutes.
Read more
More
$78.95
- Compare At:
-
$93.95
- You Save:
-
$15.00
Genuine Frigidaire part
By: Frigidaire
Part Number: 297237702
Compressor clicks but won't start? Replace the start relay when your freezer stops cooling or the compressor shuts off after a few seconds. Quick fix.
Do-It-Yourself Stories from Customers like You
Refrigerator quit cooling Mitchell M. • Jackson , GA • May 12, 2017
First I have an LG French Door with a bottom freezer. It quit cooling. I went on line and watched some very informative You Tube videos. I trouble shot according to these videos. In these videos it shows that if there is a click coming off the compressor it has too meanings, the compressor is froze or the start relay is bad. I ohmed the compressor and had no open wires in the compressor. I then shook the relay and it was making noise. The videos stated that is there is a noise in the relay...
Read more
More
$79.95
- Compare At:
-
$95.94
- You Save:
-
$15.99
Genuine Whirlpool part
By: Whirlpool
Part Number: WP3395382
The Start Switch is an OEM replacement part for Whirlpool dryers. It is an electronic component responsible for initiating the heating elements and tumble cycles upon user command from the control panel.
Causes of a bad start switch involve general wear over extended use. Failure of the internal conducting surfaces interrupts circuit activation as well.
Symptoms of a bad start switch include:
- Heating elements or tumble cycles that will not engage properly
- Dryer fails to operate or stops mid-cycle unexpectedly
- Control panel appears non-responsive to selections
- Error codes related to ignition or power delivery faults
Note: This dryer push-to-start switch has 2 terminals.
This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore electric dryer models.
Do-It-Yourself Stories from Customers like You
Dryer wouln't start heard the timer working but the starter wouldn't start Perry B. • Stockton , CA • December 05, 2014
I replaced the starter switch, that really didn't need to be replaced, and the thermal fuse, which did.
Read more
More
$50.57
- Compare At:
-
$60.68
- You Save:
-
$10.11
Genuine Whirlpool part
By: Whirlpool
Part Number: LA-1003
The Door Catch Kit is an OEM part for Whirlpool dryers. It includes the door catch and the necessary mounting hardware to secure it in place. This kit ensures the dryer door remains securely closed during operation, preventing heat loss and ensuring the appliance functions efficiently.
Causes of a bad door catch include regular wear and tear, physical damage, or misalignment of the door, which can impact the catch's ability to latch properly.
Symptoms of a bad door catch include:
- The dryer door not staying closed
- Difficulty latching the door shut
- The dryer stopping mid-cycle due to the door opening
This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
This part fixes the following symptoms
-
Door won't close
-
Shuts off too soon
-
Doesn't shut off
-
Takes too long to dry
See more...
Do-It-Yourself Stories from Customers like You
Door clip to my dryer broke Richard D. • North Dinwiddie , VA • March 15, 2014
Ordered a new clip and installed it. Easy to do. Unplugged the dryer. Removed the front. It is only held on by two screws. Removed wires to the door switch. removed the female end (it had the broken male piece in it. Inserted the new female part in the front, clipped in the male part into the door and reconnected the door switch wires, screwed the front back on. Job done.
Total time was less than 10 minutes. Works like new.
Read more
More
$25.76
- Compare At:
-
$30.65
- You Save:
-
$4.89
Genuine Ge part
By: Ge
Part Number: WE01X34284
Color: Dark Slate
The Door Strike is an OEM part for GE dryers. Positioned on the dryer frame, it securely latches the door closed during cycles. Its magnets align perfectly with the door when shut to create an air-tight barrier, enhancing energy efficiency.
Causes of failure can be normal wear, misalignment stress, or accidental damage. Over time, strikes lose effectiveness at preventing air/moisture exchange.
Symptoms of a bad door strike include:
- Excess warm air entering the dryer chamber
- The door not fully closing or latching tight
- Clothing not drying completely within expected cycles
- Buildup of lint around the door seal area
This GE part is also compatible with some Hotpoint, RCA, and Kenmore models.
More
$31.95
- Compare At:
-
$38.34
- You Save:
-
$6.39