Power Small Engine Start Switch Parts
Genuine Whirlpool part
By: Whirlpool
Part Number: WPW10420741
This push-to-start switch initiates the dryer cycle when the start button is pressed. It sends a signal to the motor and control circuit to begin tumbling and heating. Replace this switch if pressing the start button produces no response, the dryer only runs while you hold the button down, or the switch feels loose or does not click when pressed.
Do-It-Yourself Stories from Customers like You
The push start button didn't start the dryer Kirsten K. • Fayetteville , NC • July 21, 2016
I replaced the part i ordered and it worked great!
Read more
More
Genuine Bosch part
By: Bosch
Part Number: 00165256
Dishwasher won't fill or keeps overfilling? The float switch detects water levels for proper filling and draining. Accessible repair in under 30 minutes.
This part fixes the following symptoms
-
overflowing
-
Will not fill with water
See more...
Do-It-Yourself Stories from Customers like You
Inlet valve would not open to let water into the dishwasher Kurt J. • Burnsville , MN • January 09, 2015
I checked continuity at the float switch since I knew the inlet valve was working when direct wired to 120v. Switch did not have continuity. Replaced switch and inlet valve worked at start of cycle.
Read more
More
Genuine Ge part
By: Ge
Part Number: WR07X10084
Fridge clicking but not cooling? A faulty compressor start relay prevents startup. This part restores cooling in 15-20 minutes. Includes installation video.
Do-It-Yourself Stories from Customers like You
We had no power only lights on Frank A. • Smithtown , NY • January 28, 2022
GE refrigerator 12 years old and we love it. Ordered compressor overload and compressor start relay video's were great made the replacement easy. I also ordered the control board because I felt this was the real culprit again the video was the best. With all the parts replaced GE profile refrigerator has been working like new. Thank you AppliancePartsPro.com
Read more
More
Genuine Frigidaire part
By: Frigidaire
Part Number: 134762010
Fix a washer that won't fill, overfills, or shows E35 error code with this water level pressure switch. Moderate DIY repair takes about 1-2 hours.
Do-It-Yourself Stories from Customers like You
E35 Michael B. • Mechanicsville , VA • September 13, 2016
Water valve not closing all the way. Water keep entering washer even with power cord unplugged. Parts I ordered fit perfect. Ordered on Thursday night , parts there Saturday. Great service and shipping. Thank
Read more
More
Genuine Ge part
By: Ge
Part Number: WB24X10146
The Micro Switch is an OEM part for GE microwaves. This part ensures the appliance operates only when the door is securely closed. It controls the electrical circuit, allowing the microwave to start heating food when the door latch engages the switch.
Causes of a bad micro switch can include wear and tear from frequent use, electrical issues, or physical damage from slamming the microwave door.
Symptoms of a bad micro switch include:
- The microwave not starting or stopping unexpectedly
- The microwave running even with the door open
- Intermittent power issues
- The door not latching or the microwave indicating the door is open
This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.
Do-It-Yourself Stories from Customers like You
Stopped working tripped breaker Roberto M. • Pembroke Pines , FL • March 08, 2019
By replacing the switches.
Read more
More
Genuine Ge part
By: Ge
Part Number: WE1X21975
Dryer won't start or run? A blown thermal fuse is often the cause. This safety part cuts power when overheating occurs. DIY-friendly repair.
Do-It-Yourself Stories from Customers like You
Didn’t go on. Christina S. • Levittown , NY • February 16, 2018
The part I ordered fixed my problem
Read more
More
Genuine Whirlpool part
By: Whirlpool
Part Number: WPW10312185
Burner stuck on high heat or won't regulate temperature? This infinite switch restores precise control. Straightforward DIY repair with a screwdriver.
Do-It-Yourself Stories from Customers like You
Infinity switch on stove.. Thaddeus S. • Charlton , MA • February 27, 2023
Took out the old part and installed the new one.
Read more
More
Genuine Ge part
By: Ge
Part Number: WB24T10063
Fix a burner stuck on high or not heating with this infinite control switch. Common cause when burners won't adjust temperature. DIY repair in 20 minutes.
Do-It-Yourself Stories from Customers like You
Burner only worked on high setting Alejandro G. • East Meadow , NY • February 15, 2016
Ordered recommended part for GE appliance. Change was very simple. Followed instructions on video and removed one wire at a time. Very easy to change 5 to 10 minutes.
Read more
More
Genuine Whirlpool part
By: Whirlpool
Part Number: 700855K
Fix burners that won't turn on or heat up with this burner switch kit. Includes mounting hardware and instructions. Easy 30-minute DIY repair.
This part fixes the following symptoms
-
Won't start
-
Element will not heat
See more...
Do-It-Yourself Stories from Customers like You
The burner switches were not controlling the burners correctly specifically the lo temps were too high the switch knobs were also worn Frank C. • Sunset Beach , NC • December 24, 2019
1) I installed 4 ea new Whirlpool 700855K switches. (The old switches had INF-240P-871 stamped on them. 700855K was the cross-referenced P/N.)
The installation was easy. There is slight difference in the terminal arrangement: 1) the old switch has raised terminals whereas the new switch has recessed terminals (for safety), and 2) the terminal markings are slightly different: The old switch has L1/L2/P/H1/H2 (5 terminals). The new switch has L1/L2/P/HC/H1(Also five terminals. I saw where one...
Read more
More
Genuine Whirlpool part
By: Whirlpool
Part Number: W10339251
Fix a washer that overfills, won't fill to the right level, or floods. This water level pressure switch monitors tub water. DIY install in 1 hour.
Do-It-Yourself Stories from Customers like You
Water level control wouldn't work Micheal W. • Millville , UT • April 11, 2014
I replaced it and the new one fit perfectly. reassembled and fired it up. Worked as desired, like new...
Read more
More
Genuine Ge part
By: Ge
Part Number: WE4M255
Fix a dryer timer that won't advance or automatic cycles that stopped working. This timer resistor regulates cycle duration. Easy 15-minute repair.
Do-It-Yourself Stories from Customers like You
Dryer would not shut off at end of any cycle Jeffrey S. • Davis , CA • January 15, 2018
I Replaced the power resistor. The old resistor had a small burnt spot and tested infinity for resistance.The terminals were too small so I had to make new connector. Any 5000 ohm ceramic filled resistor would have worked also.
Read more
More
Genuine Whirlpool part
By: Whirlpool
Part Number: WP3399849
Dryer won't heat or start? A blown thermal fuse is often the cause. This safety component is a simple DIY fix taking about 5-10 minutes to replace.
Do-It-Yourself Stories from Customers like You
Thermostat and thermofuse Britt A. • Concord , NC • February 16, 2015
Out with the old. In with the new. No problem. Dryers are simple and usually can be fixed quickly. appliance pros makes it easier with their tutorial videos and fast shipping!
Read more
More
Genuine Ge part
By: Ge
Part Number: WE4X448
The Flame Sensor is an OEM part for GE dryers. This part detects the presence of a flame in gas dryers, ensuring that the gas ignites properly for safe and efficient drying.
Causes of a bad flame sensor can include regular wear and tear, carbon buildup from the gas flame, or electrical malfunctions.
Symptoms of a bad flame sensor include:
- The dryer not heating or taking longer to dry clothes
- The dryer shutting off unexpectedly during a cycle
- The igniter glowing but not igniting the gas
- Error codes related to heating or ignition issues
This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.
This part fixes the following symptoms
-
No heat or not enough heat
See more...
Do-It-Yourself Stories from Customers like You
Dryer heating for only a short time then no heat at all David N. • Fairfax , CA • December 08, 2018
GE Gas Dryer Model DBVH512GF1WW began to heat for only a short amount of time so drying clothes took WAY too long. Read online that the first thing to replace are the solenoids. Bought the two solenoids from AppliancePartsPros.com for about $50 total, and it seems to have fixed the problem. Had to watch a few videos to learn to disassemble the dryer, and the job took a couple of hours, but now that I know what I'm doing it could be done in less than 30 minutes.
Also, the old solenoids tested...
Read more
More
Genuine Whirlpool part
By: Whirlpool
Part Number: WP3391912
Dryer won't heat or shuts off early? The high limit thermostat monitors temperature and cuts power when overheating occurs. DIY repair in 30 minutes.
Do-It-Yourself Stories from Customers like You
My maytag gas dryer would start and the the tumbler rotate but the igniter would not glow and flame not start .gil P. • Enumclaw , WA • March 29, 2015
The 2 sensors that sit on top of the flame tube work together. The Thrmst F should check closed, as should the Cutoff-TML, in order for power to flow to the ignitor. If the Cutoff is open, it is usually because the Thrmst-F did not open soon enough. The Thermst-F will cycle, closed to open, and repeat, however the Cutoff-HTML is a one time switch. If it opens it will not return to closed, and subsequently the ignitor will not glow.
Some professionals say that if one of these sensors fail, both...
Read more
More
Genuine Speed Queen part
By: Speed Queen
Part Number: D504515
Dryer not heating or not getting hot enough? The cycling thermostat regulates temperature during the drying cycle. Moderate DIY repair for most users.
Do-It-Yourself Stories from Customers like You
Dryer problem no heat Judith T. • Suffield , CT • May 19, 2025
Replaced thermostat.
Read more
More
Genuine Bosch part
By: Bosch
Part Number: 00422748
The Potentiometer is an OEM replacement part for Bosch gas range or cooktops. It functions as a three-terminal resistor that adjusts the flow of electric current, which in turn, controls the ignition and temperature of the cooktop. This component is essential for the precise operation and control of the gas burners, ensuring they light up and maintain the desired flame intensity.
Causes of a malfunctioning Potentiometer can be attributed to wear and tear, electrical issues, or damage due to spills and cleaning products. A compromised potentiometer affects the flow of electric current, leading to issues with the ignition and temperature control of the gas burners.
Symptoms of a bad Potentiometer include:
- The cooktop not lighting or staying lit
- The ignitor continuously clicking without igniting the burner
- Inability to adjust the flame intensity or temperature accurately
This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.
Do-It-Yourself Stories from Customers like You
One burner on my thermador cooktop (pcs484ccus) would not light Kinn K. • Haslet , TX • June 08, 2015
After watching a youtube video, I disassembled the front cover on the cooktop (be sure to turn off the power supply). I then switched the potentiometers on two burners. The burner that was not working now worked and the burner that did work did not. Easy to find the culprit....ordered a new potentiometer from here and though I only got regular shipping, it was actually delivered the NEXT DAY! 5 minutes, put in the new part, and all burners work. Great site, thanks for the help!
Read more
More