Small Engine Ignition Coil Parts

In the middle of Christmas baking, I noticed that it was taking a really long time to bake bread. Since I had already done 5 batches and the timing was always the same, I knew when I had to add 20 min, something was wrong. My oven thermometer (I bought at target) no longer worked so it was hard to tell the exact temperature. First, I went and bought a new thermometer to see the actual temp, then I set the oven to 350 degrees and checked to see what the thermometer was showing. It was almost 50... Read more

I had cleaned the lint out of the dryer exhaust hose, that was usually the problem. But still no heat. I went online to AppliancePpartPros and watched the videos and was able to diagnose that I needed a new ignitor. .The parts delivered very quickly and I had the job done in 15 minutes. The repair place I called would have taken days to come out just to look at it at.. Read more

Unfortunately my first repair attempt (replacing the Gas Valve Coils) failed so I decided to replace the entire Burner assembly. From a cost/time point of view the Burner assembly is a better value than just buying the Gas Valve seeing as you don't have to disassemble/reassemble most of the existing Burner (to get to the Gas Valve) *and* you get a new Igniter!! The most annoying thing about the repair is accessing the screw that clamps the gas pipe to loosen it :-(... Read more

Yes, the part worked great. Read more

Valve (or a component on it) was slowly leaking gas. I was able to easily replace the entire gas assembly with this order. Item was mostly pre-assembled, and contained all parts needed, including new igniter and coils. Read more

Only the lower element was burned out, but I opted to replace both. Ordered from AppliancePartsPros and received them very quickly! A few screws, unplug and plug in the new elements, replaced the screws, and DONE! This has to be one of the easiest repairs a homeowner can do. Thanks, AppliancePartsPros for carrying the original equipment parts and providing the fast shipping! Read more

Unplugged the stove, unscrewed the mounting plates from the back unsnapped the wires then revered the procedure to install new one. Read more

When the element on our 15 year old builder grade oven went out we were worried it was time to spend thousands on a new oven. Instead, we found the replacement part on appliancepartspros.com and decided to give replacing it a shot, after all it was $80 instead of $1600. We weren't entirely sure the replacement was the right part because our oven model had an extra "0", but given it came up when I searched for the oven model (if not on the compatability checker) and the refund guarantee we... Read more

Replaced broiler element. Read more

Removing cabinet panels to access burner was the major challenge since every one seems to be different. This one, two screws at back allowed top to raise and be removed, Two more screws at front and two cables disconnected removed control panel. The door panel was not quite as obvious, The two screws at top sides and two at very bottom edge were removed. Then by trial, I removed screws around door edge until panel was loose. I removed a couple extra; but the whole door and panel lifted off.... Read more

• Little to no heat when baking

Was real simple--unscrewed back screws, disconnected the bad element and reconnected the good element. Was not hard at all. Read more

Removed LP Orifice and LP Gas limiter. Orifice was easy, however the gas limiter was the tricky one because I had no instructions to what went where. I could not find anything online as to how to convert from LP to Natural Gas, but you could find several things as to how to convert from Natural to LP. I ended up finding the Dryer schematic on line for the Whirlpool Duet natural gas dryer and was able to figure out what sequence the Spring, regulator and limiter went in. The order I just... Read more

• Element will not heat

I lucked out my nephew was here to deer hunt and he helped me. I do believe I could have done it on my own but was more confident with his help. I will say the videos did help. Read more

• Element will not heat

I ordered 2 bake elements and bulbs and was able to easily fix 1 of the ovens. The serviceman who repaired the left oven did not repair it correctly so, one of the wires was not accessible so, I could only fix one oven. After shutting off the power, I EASILY fixed the right oven - with a LOT of care and a little elbow grease - in disconnecting the broken element, by doing exactly as it said to in the video, making certain not to allow the wires to slip back into the hole that it was pulled... Read more

• Element will not heat
• Little to no heat when baking
• Oven not heating evenly

Removed 2 sheet metal screw pulled element out about 2 inches. Removed two Spade connections. Removed the element from the oven. Inserted the new element into the over, connected the two spade connector. Reinstalled the two sheet metal screws. Set the oven to bake for testing and tested until the element turned red. Total time less than 5 minutes. Read more