Ce Small Engine On-Off Switch Parts
Genuine Whirlpool part
By: Whirlpool
Part Number: WP4456905
Provides electrical connection and control for gas burner ignition on cooktop surfaces. Replace if burners won't light, produce weak sparks, or if you hear clicking without ignition.
Do-It-Yourself Stories from Customers like You
The front two electronic igniters on the stove top range stopped working Raymond L. • The Woodlands , TX • December 26, 2015
I called a rpair service. The men came to the house, torn apart the stove top and advised Replacement of the wire harness. The trip charge of $100 would be deducted from a repair bill of $350, thus they needed an additional $150 for parts and $100 for labor after paying the trip charge. I bought the harness for $60, and the star bits I needed for my drill for $10. My son and I installed the new harness in about 30 minutes, which included a thorough cleanup, saving us $180.
Read more
More
$116.50
- Compare At:
-
$139.80
- You Save:
-
$23.30
Genuine Frigidaire part
By: Frigidaire
Part Number: 5304493153
The Door Switch is an OEM replacement part for Frigidaire wall ovens. It is a component located on the oven door that detects when the door is opened and closed. The door switch works alongside the control board to regulate oven operations based on door position.
Symptoms of a bad door switch can include:
- Oven failing to automatically go into bake or warm modes after door closure
- Interior lights not turning on when the door is opened
- Control buttons/display remaining constantly lit instead of dimming
- Oven not heating or functioning properly in different modes
Causes relate to normal wear over extended use as the door switch mechanism cycles with frequent door openings and closings. Moisture exposure or impacts could also degrade switch performance.
This OEM Frigidaire switch is compatible with Amana, Jenn-Air, KitchenAid, and some Electrolux wall oven models as well.
Do-It-Yourself Stories from Customers like You
Frigidaire microwave oven lights and timer work but oven doesn't heat Reese F. • Essex Junction , VT • August 16, 2015
I diagnosed this problem via the web and the advice was spot on. The problem was a failure of the bottom door switch. I used a multimeter to verify that the switched never closed properly. It took me a minute to figure out how to remove the old switch (press a release tab under the switch while simultaneously rotating counter-clockwise). That was about the most difficult part of the repair.
Read more
More
$64.39
- Compare At:
-
$76.62
- You Save:
-
$12.23
Genuine Frigidaire part
By: Frigidaire
Part Number: 5309918806
This door-activated light switch controls the interior lamp in your refrigerator. Replace a worn or sticking switch to restore dependable lighting and prevent the bulb from staying on and warming the compartment when the door is closed.
- Opens and closes the light circuit as the door is opened and closed
- Helps prevent the light from staying on with the door shut
- Common symptoms: interior light won't turn on, stays on with the door closed, or works intermittently
- Physical signs may include a stuck/broken plunger or damaged housing
What's included: One light switch Install notes:
- Disconnect power before servicing
- Gently pry the old switch from the liner/panel and release its locking tabs
- Transfer wires one at a time to the same terminals on the new switch
- Press the new switch fully into place; restore power, and test
Do-It-Yourself Stories from Customers like You
Light didnt turn on Robert R. • New Britain , CT • May 25, 2015
Well started with the bulb switch when that didn't work, i continue with the next switch which was the door switch, then it worked just make sure the light bulbs are good, because i went thru 4 bulbs
Read more
More
$37.53
- Compare At:
-
$44.66
- You Save:
-
$7.13
Genuine Samsung part
By: Samsung
Part Number: DA34-00006C
The Refrigerator Door Switch ensures your Samsung refrigerator operates smoothly by accurately detecting when the door is opened or closed. This genuine OEM part is specifically designed for Samsung refrigerator models, providing a reliable and secure fit. With the door switch functioning correctly, your refrigerator maintains optimal cooling and energy efficiency, preventing issues such as improper temperature control or excessive energy usage. Installing this switch is straightforward, allowing you to quickly restore your applianceGÇÖs functionality without hassle. By choosing this genuine OEM part, you benefit from guaranteed quality and compatibility, ensuring your refrigerator continues to keep your food fresh and organized. Enhance your refrigeratorGÇÖs performance and extend its lifespan with the dependable Refrigerator Door Switch .
This part fixes the following symptoms
-
Ice maker not making ice
-
Not dispensing water
-
Light not working
See more...
Do-It-Yourself Stories from Customers like You
Samsung refrigerator rb2055sl door alarm beeping continuosly light out and temperature would jump from 34 degrees to 67 degrees Helen L. • Miami , FL • December 05, 2015
Ordered the Door Switch. Arrived the next day. It took less than 5 minutes to install the new switch. The beeping stopped immediately, light worked and temperature gauge showed 34 degrees.
Read more
More
$46.26
- Compare At:
-
$55.05
- You Save:
-
$8.79
Genuine Whirlpool part
By: Whirlpool
Part Number: WPW10249845
This water level pressure switch senses tub water level and signals the control to stop filling and advance the cycle. Replacing a failed switch restores proper fill shut-off and allows the washer to move to wash, drain, and spin.
- Detects water level via air pressure in the attached hose from the tub air dome
- Signals the timer/control to close inlet valves at the selected fill level
- Enables agitation and spin only when the level is appropriate or the tub is empty
- Typical symptoms of a failed switch include overfilling or underfilling, continuous filling, cycle not advancing, or no spin
What's included: 1 water level pressure switch Install notes:
- Disconnect power and turn off water supply before servicing
- Access the switch in the control console or top panel; note wire locations for reassembly
- Transfer the pressure hose and wire connectors to the new switch one at a time; ensure the hose is clear, not kinked or cracked, and fits snugly
- After installation, run a quick fill test to ensure proper shut-off and cycle progression
Do-It-Yourself Stories from Customers like You
Intermitten f21 error Bill D. • Hornell , NY • March 11, 2015
After trouble shooting what f21 error was. I cleaned all hoses from the tube hose to all discharge hoses. I actually replace the washer discharge hose. I still got the same error. I had a few conversations with your service techs. They gave me great advice each time I called. At the end I had to replace the washer drain pump and pressure switch. we have gone 1 week without errors code so I consider the problem solved. I really like the replacement part videos. I also like the ease of...
Read more
More
$161.76
- Compare At:
-
$190.88
- You Save:
-
$29.12
Genuine Whirlpool part
By: Whirlpool
Part Number: WPW10411937
Dryer won't start or run? A faulty belt switch often causes this when the belt snaps or slips. This switch monitors belt tension and is a fairly easy fix.
Do-It-Yourself Stories from Customers like You
Drum wouldnt turn power to control panel but wouldnt start Andy S. • Arlington , VA • November 03, 2016
Replaced motor "triple switch" Part Number: AP6021090 and the thermal fuse
Read more
More
$28.43
- Compare At:
-
$34.12
- You Save:
-
$5.69
Genuine Lg part
By: Lg
Part Number: EBF60662911
This is a spark ignition switch assembly with wiring harness that controls the electric igniters on a gas range cooktop. It sends voltage to the spark modules when a burner knob is turned, initiating the clicking ignition sequence. Replace this part if your burners won't spark when turned on, spark continuously even when knobs are in the off position, or if only some burners ignite properly.
This part fixes the following symptoms
-
Doesn't shut off
-
Gas igniter glows, but will not light
See more...
Do-It-Yourself Stories from Customers like You
All the igniters spontaneously began to fire Michael S. • Adams , NY • October 12, 2019
Found a YouTube video online that provided instruction on how to change out the part.
Read more
More
$74.95
- Compare At:
-
$89.19
- You Save:
-
$14.24
Genuine Whirlpool part
By: Whirlpool
Part Number: W11050715
This replacement switch restores reliable on/off signaling to the circuit it controls, helping your appliance start, stop, and respond correctly. A worn switch can cause intermittent operation, no response, or lights and functions that don't activate. What it does:
- Provides an electrical open/closed signal to enable functions like starting a cycle, powering a motor or light, or shutting a feature off
- Acts as a safety/position interlock (such as door, lid, float, or hood) depending on the model
- Typical symptoms include won't start, won't stop, light won't turn on/off, or intermittent operation
- Can be checked with a multimeter for continuity when actuated
What's included:
Install notes:
- Disconnect power before servicing; turn off gas or water supply if applicable
- Access the switch, note wire locations, and transfer leads one at a time to the new switch
- Mount securely, ensure the actuator aligns and wires aren't pinched
- Reassemble and test operation before finalizing
More
$9.49
- Compare At:
-
$9.54
- You Save:
-
$0.05
Genuine Ge part
By: Ge
Part Number: WB24T10147
This is a high-amp SPDT (single pole, double throw) switch used in the oven door mechanism. It detects whether the oven door is open or closed and signals the control to enable or disable certain functions such as the oven light or broil element. Replace this switch if the oven light does not turn on or off when the door is opened or closed, or if the oven does not operate correctly in relation to door position.
Do-It-Yourself Stories from Customers like You
Faulty self cleaning latch Gregory K. • Bel Air , MD • December 28, 2016
Replaced faulty latch with new latch. New latch was different configuration, but the fit was okay. The only issue was that the wires to the electric motor were just barely long enough.
Overall easy repair if you have a T15 Torx bit, phillips screwdriver, and 1/4" nut driver. Hardest part is removing the gas cooktop to gain access to the cleaning latch. 0. Turn off electric to stove; remove the cast iron grates, center caps/orifices, and catch pans from the stovetop. 1. Disconnect the...
Read more
More
$23.30
- Compare At:
-
$27.49
- You Save:
-
$4.19
Genuine Whirlpool part
By: Whirlpool
Part Number: WP22001656
This is the washer's water level switch that senses tub level via air pressure and provides five selectable fill settings. Replacing a failed switch restores accurate filling and lets the cycle advance properly through wash, rinse, and spin.
- Monitors air pressure from the tub to detect actual water level
- Controls the inlet valves to start/stop filling at the selected setting
- Signals the timer/control to begin agitation and advance the cycle once full
- Common symptoms: overfilling or water keeps running, stops filling too soon or won't fill, inconsistent water levels, cycle won't advance due to incorrect level detection
What's included: 1 water level pressure switch with 5-position rotary selector Install notes:
- Disconnect power and turn off water supply before servicing
- Access the control console; remove the selector knob/dial and panel as needed
- Note wire locations (take a photo), move the harness, and transfer the pressure hose; ensure the hose is clear and firmly seated
- Securely mount the new switch, reassemble the console/knob, restore utilities, and test each fill level
Do-It-Yourself Stories from Customers like You
Water level in Maytag washer was always high and was not adjustable Von D. • San Bernardino , CA • December 21, 2017
Replaced the water level switch and water level pressure switch hose. Video on AppliancePartsPros.com detailed the procedure.
Read more
More
$127.65
- Compare At:
-
$153.18
- You Save:
-
$25.53
Genuine Bosch part
By: Bosch
Part Number: 00611312
This switch is mounted on the dishwasher frame and detects when the door is properly closed to allow the wash cycle to begin. Replace it if your dishwasher won't start even with the door firmly closed, or if it stops mid-cycle unexpectedly.
Do-It-Yourself Stories from Customers like You
Dishwasher would not start. Jason M. • Florence , SC • November 30, 2020
REPLACED DOOR LATCH AND DOOR LATCH ASSEMBLY. EVERYTHING WORKS AGAIN.
Read more
More
$37.95
- Compare At:
-
$45.16
- You Save:
-
$7.21
Genuine Frigidaire part
By: Frigidaire
Part Number: 318191000
Burner won't heat, stuck on high, or works intermittently? This cooktop burner control switch restores reliable on/off control. Easy DIY repair.
Do-It-Yourself Stories from Customers like You
I am buying a few new replacement parts for my frigidaire 40' range before the need arises they no longer make that size and i had my kitchen changed to fit this range e just iare William M. • Fishers , IN • January 23, 2016
I worked with Bud and he was most helpful. I was very happy with the service that was offered. I liked the quick shipment, good packing and only paying ONE time for shipping.
I would recommend your company again and would ask to deal with Bud again.
Thanks for you service.
Read more
More
$82.46
- Compare At:
-
$103.97
- You Save:
-
$21.51
Genuine Frigidaire part
By: Frigidaire
Part Number: 318394803
Has three terminals.
Do-It-Yourself Stories from Customers like You
Oven light stayed on when door was closed Robert S. • Jacksonville , IL • June 14, 2015
When trouble shooting the problem I found that the light switch housing outer lip was broken allowing the switch to push through mounting surface behind the oven door. This is a slide in range so, I proceeded to pull the range away from the counter where I could unplug the power cord. Once the power was off like located the panel on the right upper side of the unit and removed the screws to allow access to the switch. I then unplugged the switch from the wiring harness and removed the damaged...
Read more
More
$53.95
- Compare At:
-
$64.20
- You Save:
-
$10.25
Genuine Speed Queen part
By: Speed Queen
Part Number: 202937
If your washer overfills, underfills, or won't advance cycles, the water level pressure switch may have failed. Takes about 10-15 minutes to replace.
Do-It-Yourself Stories from Customers like You
Broken pressure switch Carole Y. • Yakima , WA • November 06, 2019
Bought part from you and got a repairman to put it in. Darlene of your staff found part I needed. Nice lady! Repairman charged $82 to do a 10 minute job. Not your fault!
Read more
More
$123.95
- Compare At:
-
$147.50
- You Save:
-
$23.55
Genuine Whirlpool part
By: Whirlpool
Part Number: 9871829
Fix a compactor that won't start, stops mid-cycle, or requires holding the pedal down. This drawer tilt switch is a quick 15-second replacement.
Do-It-Yourself Stories from Customers like You
Compactor would start sometimes by just closing the door when you start it by normally lifting the pedal it would not stop at the end of it's cycle Bruce H. • Hewitt , NJ • January 19, 2015
I replaced the upper switch that contacts the door in a closed position and more important the start switch contacted by lifting the start pedal.
Read more
More
$50.57
- Compare At:
-
$59.67
- You Save:
-
$9.10
Genuine Whirlpool part
By: Whirlpool
Part Number: W11162115
Burner stuck on high or won't regulate temperature? The infinite switch controls heat levels. Common DIY repair, typically 10 minutes to install.
Do-It-Yourself Stories from Customers like You
Switch was worn out Neil F. • Bellevue , WA • December 05, 2025
Replaced it myself after watching YouTube video. Simple and fast!
Read more
More
$78.27
- Compare At:
-
$92.36
- You Save:
-
$14.09