Hardware Hand Small Engine Ignition Coil Parts

With the help of Wendee and Karen, we finally figured out my model numbers and which parts where correct. I ordered the parts and all arrived the next day except for the Broiler element which arrived in 2 days. I installed the new Baking Element myself. Took longer to figure out which curcuit braker to turn off. In about 30 minutes I had a brand new Baking Element in my oven working perfectly. On the following day, I installed the Broiler Element. That took a bit longer as it sits in a metal... Read more

Little procrastination paid off. With only 50% capability I knew it is time to call the appliancepartspros. They shipped me parts within 3 days. It was practical to fix both at the time. All I needed was to disconnect power at range breaker box, grab a screwdriver to lift top open, a 16 inch or so piece of old 2×4 wood to keep the top top of stove lifted, so I could access heating elements from underneath. Then I took my black sharpie And marked location of mounting screws and... Read more

Turned off power to oven. Removed the oven door. Unscrewed and removed the metal plate. Pulled element off wires and attached them to the new element. (This took needle nose pliers and many attempts. Needed dexterous fingers and good eyesight.) Put everything back. Read more

• Element will not heat

My 1984 GE Electric Stove model number was very close to an another entry, but not actually in appliance repair pros' model numbers list. But my burners looked and measured the same for the near entry number, and the surface unit control switch looked very similar. I decided to take a chance and ordered 2 of each.. (Actually I wouldn't have needed new burners but an earlier "repair guy" took 2 of my burners and never returned - and no one could find him!) It turned out the new burners fit... Read more

I first tried to purchase the part directly from GE but they were not helpful at all. Remembering that I had purchased a transmission and other parts from appliance parts pros for my old Maytag washer before, I searched their easy-to-use parts catalog and there it was!!!! I asked for confirmation from Customer Service and after 2 says Research confirmed that it was the correct part. Replacing the element was quite simple following the very helpful diagrams on their website. Thank you so very... Read more

Isolated the problem to extreme frost build up on the evaporator coils. I measured an open circuit on the defrost heater/thermostat, so I ordered both. Following the procedure in the GE service manual for this refrigerator, I gained access to the evaporator in the back of the freezer section, and I replaced the both heater element and the defrost thermostat. Refrigerator cools fine now. The most unexpected thing was how quickly the parts came. They arrived at my front door 18 hours after... Read more

Replace burner Just like before part came fast was correct, works fine Read more

Changed element Read more

After having a refrigerator repairman come 2 x’s to fix and it kept icing up then calls to the refrigerator repair were going unanswered I decided I was going to fix it myself. I watched 2 YouTube videos and decided I could do that. I order all the parts to change everything that could possibly be causing this. Heating element, defrost sensor, and 2 different temperature sensors. I figured if I was going to take the refrigerator apart I might as well try everything rather than having to do... Read more

Following the instructions that I received through the helpful research of the APP staff, I disconnected the power, disassembled the back of the oven, and accessed the hidden element. This involved bending parts of the sheet metal and cutting the insulation, so I was very apprehensive about doing this. Once I exposed the compartment that contains the element, I had difficulty extracting the old part and was really nervous about pulling hard to extract it - until I saw the damaged element. It... Read more

• Little to no heat when broiling
• Element will not heat

Quick shipping, easy repair. Read more

• Little to no heat when broiling

Cut off power ,inside I remove the two back screws, remove the two front screws with hangers. Pull element out, clip wires so they don't fall back in holes with clothes pins. worked good. But wire connection to the broiler was to large, had to replace connectors, wire fell in hole, had to pull wall oven out and remove back panel. I then mounted the new element to oven. Replaced connectors ,connected connectors, closed back panel, put oven in place ,connected power lines. Turned power on. Works... Read more

• Little to no heat when broiling

I ordered a broiler element, watched the video and replaced the element when it arrived. I turned off the electrical breaker to the stove/oven. I then removed the oven door from the hinges and removed the 1/4" square head screws that secured the element in place,( the video showed phillip head screws ), removed the element wires from the old element. Replaced the element wires to the new element and reattached the element to the oven with the hex head screws. I then put the oven door back on... Read more

• No heat or not enough heat

Removed back panel of dryer. Pulled out part out of its clamp. Placed new igniter in clamp, then dried some clothes and it worked. Read more

When I pulled out the dryer from the wall, I could see dust/lint had accumulated everywhere and the vent system was compromised. I vacuumed up the dust/lint accumulation outside and then inside the vent system. I then opened the lower cabinet to clean and check its condition. I removed the water steamer bottle and its sub-assembly and then the drum. After cleaning and inspecting components — both visually and with a multi-meter I determined the problem was the appliance doing what it was... Read more