Hardware Hand Small Engine Safety Switch Parts

This replacement screw secures appliance panels, brackets, and internal components. It restores a tight, rattle-free fit and proper alignment when an original fastener is missing, stripped, or corroded.

• Fastens metal or plastic parts to the cabinet/frame
• Helps maintain alignment and reduce vibration or rattling
• Direct replacement for lost, damaged, or rusted hardware
• Keeps covers and brackets safely in place

• Disconnect power before servicing; for gas appliances, also shut off gas supply
• Match one-for-one with the original screw; verify length/type before installation
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Use the correct driver bit to prevent stripping the screw head

The Door Switch is an OEM replacement part for Frigidaire wall ovens. It is a component located on the oven door that detects when the door is opened and closed. The door switch works alongside the control board to regulate oven operations based on door position.  

Symptoms of a bad door switch can include:

• Oven failing to automatically go into bake or warm modes after door closure
• Interior lights not turning on when the door is opened
• Control buttons/display remaining constantly lit instead of dimming
• Oven not heating or functioning properly in different modes

Causes relate to normal wear over extended use as the door switch mechanism cycles with frequent door openings and closings. Moisture exposure or impacts could also degrade switch performance.

This OEM Frigidaire switch is compatible with Amana, Jenn-Air, KitchenAid, and some Electrolux wall oven models as well.

This replacement switch restores reliable on/off signaling to the circuit it controls, helping your appliance start, stop, and respond correctly. A worn switch can cause intermittent operation, no response, or lights and functions that don't activate. What it does:

• Provides an electrical open/closed signal to enable functions like starting a cycle, powering a motor or light, or shutting a feature off
• Acts as a safety/position interlock (such as door, lid, float, or hood) depending on the model
• Typical symptoms include won't start, won't stop, light won't turn on/off, or intermittent operation
• Can be checked with a multimeter for continuity when actuated

• 1 switch

• Disconnect power before servicing; turn off gas or water supply if applicable
• Access the switch, note wire locations, and transfer leads one at a time to the new switch
• Mount securely, ensure the actuator aligns and wires aren't pinched
• Reassemble and test operation before finalizing

This is a genuine OEM replacement nut that is used on convection oven fans. This nut holds the fan onto the spindle. If the nut becomes lost during repairs to the fan, it will need to be replaced before the fan will work. This nut locks the fan to the spindle to turn and move the air around inside the oven. The fan helps the food to cook more evenly and reduces areas in the oven that are not cool enough or hot enough. If the fan is not working, the convection oven will not cook correctly.Convection ovens are different from regular ovens, and the fan is part of the reason. Convection ovens use the fan and an exhaust system to move the heat around inside the oven to cook food more evenly and faster. Many convection ovens have a setting that allows the oven to be used as a regular oven. If the nut is missing and the fan is inoperable, the oven can be used for regular cooking if it has this feature. Otherwise, the convection oven should not be used until the nut is replaced.This nut is a silver metal replacement part that is sold individually. It is designed for use in convection ovens made by GE and Kenmore.

This is a high-amp SPDT (single pole, double throw) switch used in the oven door mechanism. It detects whether the oven door is open or closed and signals the control to enable or disable certain functions such as the oven light or broil element. Replace this switch if the oven light does not turn on or off when the door is opened or closed, or if the oven does not operate correctly in relation to door position.

This hardware kit contains the screws, bolts, and mounting components needed to install an over-the-range microwave to the wall and upper cabinet. It provides the necessary fasteners to securely anchor the microwave in place during installation. Use this kit if you are missing the original mounting hardware or if existing hardware is stripped, damaged, or incompatible during a replacement installation.

ST10-16 X 7/16"

Washer won't spin or door won't lock? This door lock spin enable switch signals the control to start high-speed spin. Moderate DIY repair, 30-60 minutes.

This switch is mounted on the dishwasher frame and detects when the door is properly closed to allow the wash cycle to begin. Replace it if your dishwasher won't start even with the door firmly closed, or if it stops mid-cycle unexpectedly.

Burner stuck on high or won't regulate temperature? The infinite switch controls heat levels. Common DIY repair, typically 10 minutes to install.

The Screw is an OEM replacement part for Whirlpool ranges. This screw is used to secure various components of the range, ensuring that parts such as panels, brackets, or burners remain firmly in place during operation. It is designed to withstand the high-heat environment of a range, providing long-lasting durability.

Symptoms of a bad or missing Screw include:

• Loose or misaligned range components
• Rattling or unusual noises during operation
• Difficulty maintaining the range's structural stability

Causes of a failing or missing screw can include normal wear over time, accidental loss during maintenance or repairs, or damage from overtightening. Replacing faulty screws ensures the appliance remains safe and functional.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This is a spark ignition switch used on a range or cooktop that controls the electric spark to ignite the surface burners when the control knob is turned. It connects to the burner igniter circuit and signals when to fire the spark module. Replace this switch if your burners won't ignite, the spark clicks continuously even after the flame is lit, or the igniter fails to spark when the knob is engaged.

Chrome screw secures handles, door trim, and internal components in ranges and ovens. Replace if lost during cleaning, stripped, or missing after moves.

Burner won't heat, stuck on high, or works intermittently? This cooktop burner control switch restores reliable on/off control. Easy DIY repair.

The Switch is an OEM component specifically designed for Frigidaire washing machines. It controls various cycle options like water temperature levels, spin speeds, and additional settings like stain removal cycles.

Causes of a bad switch can include water or chemical damage leading to component failure over time, or loose wiring connections causing intermittent issues.  

Symptoms of a bad switch include: 

• Inability to select wash cycles or adjust settings  
• Unresponsive or inaccurate temperature levels
• Lights/displays not functioning as normal
• Error codes indicating switch problems

This OEM Frigidaire replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models. Replace yours today to avoid expensive repairs down the road.
 

Secures microwave to mounting bracket. Replaces stripped, cross-threaded, or missing cage nuts. Installs inside cabinet housing for stable installation.