Need Help?
Call
Dispenser not opening or leaking rinse aid down the door? This assembly restores proper detergent release. Most DIYers complete installation in 30-60 minutes.
I ordered a new vario motor and a soap dispenser. I turned off the water and the breaker, disconnected the water line and the power at the front base of the unit, disconnected the drain hose from the garbage dispenser, and pulled out the dishwasher and laid it on a blanket on its face. I unscrewed and removed the plainly visible vario motor on the bottom of the machine and removed the cam from the shaft. I then used a needle nose plier to carefully turn the D-shaft on the new motor to exactly... Read more
Fix a broken or cracked dispenser drawer handle that won't open or close properly. Simple snap-in replacement takes about 2 minutes with no tools required.
I called and was given fabulous service. I received the part the next day. It just snapped in. Read more
Washer won't start or fill with water? A faulty lid switch assembly with fuse is often the cause. DIY-friendly repair—most complete it in under an hour.
Removed front and top panels of washer, removed old switch assembly. Then mounted and hooked up new switch assembly, put panels back on, turned on power and unit now works fine. Thanks for the quick delivery on the part...our total machine down time was only 36 hours. Biggest difficulty was getting the machine out of its position to work on it! Read more
This door switch senses whether the appliance door is closed and signals the controls to run only when it's safe. Replacing a worn or intermittent switch restores dependable starts and proper shutoff when the door opens. What it does:
The Dual Element Surface Switch is an OEM part for Frigidaire electric ranges and cooktops. It governs power distribution to the dual element.
Causes may be loose electrical terminals within the switch, defects from past power surges, or general wear over extended use.
Symptoms of a bad surface switch include:
This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.
I replaced both the large single element and the large dual element control switches. It appears the resistors were burning out. Problem seems to be fixed. Will know later when I do some simmering. Read more
Fix a washer stuck mid-cycle or showing overfill errors with a new water level pressure switch. This part detects water levels to control fill cycles.
Machine was a front load washer, after doing some research found that problem is usually caused by pressure sensor or the spider arm which attaches motor to tub. Read more
Fix washer overfilling or won't fill issues with a new water level pressure switch. Prevents flooding and restores proper fill cycles. 10-minute DIY repair.
Replaced the water-level switch and hose. Washer works again, no overflowing since! Read more
Fix a washer that won't agitate or spin with this lid switch. This safety part detects if the lid is closed. Easy DIY repair with basic tools.
Replaced lid switch and capacitor Read more
Fix fabric softener not dispensing or leaking onto clothes. This top-load washer dispenser snaps onto the agitator in minutes. Easy DIY replacement.
I removed the old one by lifting up and setting aside. I opened the box and set new part in place. There were no screws and other parts to assemble and the install was very easy! Read more
This lid switch is the washer's safety interlock. It detects when the lid is closed so the machine can agitate and spin, and cuts power when the lid is opened to stop operation and enhance user safety.
Was set to pull the trigger on a new washer since this one was 10+ years old. Broke a $25 lid switch fumbling to get the washer open before I found the appliancepros video library. Once I got things apart the right way I was able to diagnose the problem in 5 minutes. Identified the $10 part needed. Got the $10 coupling and the $25 switch and had the washer working like new in 20 minutes. I'm pretty proud of myself.. not going to tell anyone about the $25 switch. Read more
Fix burners stuck on high or not regulating temperature with this range infinite switch. Controls heating element power for precise cooking control.
Using the video on your site I was able to make the repair. It was a pretty straight forward repair. Thanks for having the diagram on your site for helping me find the right part. Read more
Replace cracked or peeling dispenser cover label. Easy DIY fix—peels off like a sticker, alcohol wipe surface, press new label on. 10-minute repair.
Removed old label, took the glue residue off, wiped it down with rubbing alcohol then attached the new label on to the fridge. Read more
If your range burner won't turn on or off properly, or the indicator light stays on when turned off, this infinite switch restores control. DIY repair.
Remove front panel and replaced. Received parts fast. Read more
This door release lever connects the push-button to the latch assembly inside the microwave. Replacing a worn lever restores smooth, reliable door opening so the button works on the first press.
It took a long time to determine the problem but eventually I discovered that the plastic bracket (latch hook) that held the three door-switches showed appreciable wear from repeated door openings and closings. This wear stopped the door from sealing properly and the door switch safety mechanism blew the line fuse. I replaced the worn bracket (AP6230612) as well as the plastic latch mechanism (AP4553585) on the door that engages this bracket (and of course the fuse too) and the microwave now... Read more
Fix liquid remaining in dispenser or broken/warped detergent tray. Direct replacement snaps into place in seconds without tools. Easy DIY repair.
I replaced the part. Read more
Fix unresponsive ice or water dispenser buttons with this control touchpad. Simple 15-minute snap-in replacement—disconnect power, unsnap old part, reconnect wires.
Using the model number of the frig, I located the part (Interface Dispenser Asm) on the AppliancePartsPros.com. After reading the Q&A section for hints on how to change the part and looking at a couple of YouTube videos, it seemed that I was up to the task. I placed the order for the part and was pleasantly surprised that it arrived in a couple of days. Armed with a flat blade screwdriver and an old credit card, it took me about 15 minutes to first remove the bezel around the ice dispenser... Read more
By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.