Coil Parts

This 9-inch dual radiant surface element kit replaces a failed burner on a smooth-top electric range or cooktop, restoring dependable, even heating and letting you choose a smaller or larger heating area to match your cookware.

• Provides two selectable heating zones (inner and outer rings) to match pot size
• Heats cookware evenly across the chosen zone on glass-ceramic cooktops
• Typical symptoms include no heat, only one ring working, slow or uneven heating, or intermittent operation
• Restores burner performance after internal failure of the element assembly

• Disconnect power at the circuit breaker before servicing; 240V shock risk
• Allow the cooktop to cool completely; protect the glass surface while working
• Photograph wiring and transfer leads one at a time to matching terminals on the new element
• Ensure the element seats correctly in its support brackets; test both inner and outer rings before final reassembly

Range burner not heating? This 8-inch surface element restores even heating to your cooktop. Simple plug-in replacement takes under 10 minutes with no tools.

Burner not heating or burned out? This surface heating element restores your cooktop. DIY-friendly repair with online video guides available.

Burner won't heat or heats unevenly? This 6-inch surface element restores consistent heating. Straightforward repair with minimal tools required.

Fix ice buildup on evaporator coils with this defrost heater. Solves blocked vents and poor cooling. Mounts at evaporator, moderate DIY repair.

This secondary gas valve solenoid coil energizes the dryer's gas valve so the burner can ignite and stay lit. Replacing a weak or failed coil restores consistent heat and helps resolve intermittent no-heat or flame drop-out issues. What it does:

• Works with the companion coil to open and hold the gas valve during burner operation
• A weak/open coil can cause tumbling with no heat
• Burner lights then goes out within seconds or heats intermittently
• Repeated clicking or glowing igniter without flame

• 1 secondary gas valve solenoid coil

• Disconnect power and shut off gas supply before servicing
• Access the burner/gas valve assembly; note wire positions and remove the old coil/retainer
• Seat the new coil on the valve stem, secure the retainer, and reconnect wiring firmly
• Restore gas and power; run a test cycle and check for leaks

• If one gas valve coil has failed, the companion coil is often near end-of-life; replacing both together can improve reliability

Burner won't heat or only works on one setting? This surface heating element restores even heat to your cooktop. Simple plug-in replacement.

Fixes range that won't broil or broil element not heating. This broil heating element restores high-heat broiling. Moderate DIY; allow 1-2 hours.

This is a 2500-watt circular heating element located at the rear wall of the oven cavity, surrounding the convection fan. It provides even heat distribution during convection baking and roasting by working in conjunction with the fan. Replace this element if your oven is not heating properly in convection mode, food is cooking unevenly, or the element is visibly damaged or broken.

The Surface Element is an OEM part for Frigidaire electric ranges and cooktops. It is the individual electric coil located beneath the cooktop that provides heat.

The surface element heats up rapidly upon activation in order to boil, simmer or saute foods efficiently. Its precise heating capabilities assist home cooks in meal preparation.

Causes can be mineral deposits caked onto the element surface over time reducing its ability to transfer heat properly. Excess moisture exposure can also damage internal wiring.

Symptoms of a bad surface element include:

• Burners that do not heat up at all or heat unevenly
• Lights flickering below an element when in use
• Popping, buzzing or crackling noises coming from below an element

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This replacement coil controls the gas valve's opening and holding action during burner operation. Replacing a weak or failed coil restores reliable ignition and steady heat for consistent drying performance. What it does:

• Powers the valve to open during ignition (booster) and keeps it open while heating (holding)
• Helps resolve: igniter glows but no flame, burner lights then shuts off, no heat, intermittent heat/long dry times
• Restores proper gas flow for consistent temperatures
• Direct-fit electrical connection for the valve solenoid

• 1 booster & holding coil

• Disconnect power and shut off gas supply before servicing
• Allow the burner assembly to cool; access the gas valve compartment
• Label and disconnect wires; replace the coil in the same orientation; secure clips/brackets
• Restore gas, check for leaks with an approved solution, then test burner operation

Restore reliable, even heat to a single cooking zone with this surface heating element. It replaces a failed top burner element on an electric range or cooktop so pots and pans heat consistently for everyday cooking. What it does:

• Supplies controlled heat to one cooktop burner zone
• Helps resolve: burner won't heat, intermittent heating, or very slow heat-up
• Can address uneven heating or visible damage to the element
• Replaces an open/failed element to restore normal cooking performance

What's included:

• 1 surface heating element

Install notes:

• Disconnect power at the breaker and allow the cooktop to cool completely before servicing
• Access the element per your model's service manual; support the cooktop if lifting a glass top
• Note wire locations and transfer connections one at a time to the new element
• Secure the element with existing brackets/clips as designed, then test operation before reassembly

Fixes frost buildup on evaporator coils and inconsistent cooling. This refrigerator defrost heater melts ice during defrost cycles. 20-minute repair.

Burner not heating or heating unevenly? This 8-inch surface element restores reliable cooktop performance. Simple plug-in installation in minutes.

All metal liner SxS production built January 2003 through January 2007 (serial numbers AF through AM): Models BSS, DSS, ESH, GSH, GSS, GST, HSS, SSS

This replacement heating element restores consistent, reliable heat so your appliance reaches and maintains temperature as designed. A worn or open element can lead to long heat-up times or a complete loss of heat. What it does

• Converts electrical energy into heat for proper operation
• Helps the unit reach and hold the set temperature
• Common symptoms of a failed element: no heat, slow to heat, uneven heating, visible cracks/blisters, or tripping the circuit breaker

• 1 heating element

• Disconnect power at the breaker or unplug before servicing; allow the unit to cool completely
• Note wire positions and move connectors one at a time to the new element
• Secure all mounts and ensure terminals are fully seated with no loose connections
• After reassembly, restore power and monitor the first heating cycle