Outer Ecb Parts

Fix a washer stuck on rinse or spin cycle with this electronic control board. Restores responsive controls and accurate cycle timing. Moderate DIY repair.

Fix washer won't start, stops mid-cycle, or skips rinse with this electronic control board. Moderate DIY repair with connector-based installation.

If your range clock is flickering or oven buttons won't respond, the control board likely failed. Moderately difficult repair requires removing the control panel.

Dishwasher won't start, stops mid-cycle, or won't dry? The control module manages timing and powers all cycles. Moderate DIY repair restores function.

This mechanical cycle timer controls the sequence and duration of washer operations. Replacing a failing timer restores proper advancement through fill, agitate, drain, and spin so cycles complete reliably with accurate timing. What it does:

• Advances the washer through each step by routing power to the water valves, motor, and drain pump at the correct times
• Sets the length of each stage for consistent operation
• Common failure signs: cycle won't advance or stops mid-cycle
• Timer knob doesn't move or must be jiggled to run
• Skips functions (no agitate, drain, or spin) while others still work

• 1 mechanical timer assembly

• Disconnect power before servicing; access the timer from the control console
• Take photos or label wires; transfer them to the new timer one at a time to maintain correct positions
• Reuse the existing knob and dial; align the timer shaft properly and secure the mounting screws
• After reassembly, run a short test cycle to ensure proper advancement

Fixes oven showing ERR code, not heating after preheating, or won't start without resetting breaker. Controls temperature, timers, and display functions.

This UI board assembly replaces the refrigerator's user interface/control board to restore button response and display feedback. It lets you reliably set temperatures and modes so the appliance accepts and shows commands correctly. What it does:

• Receives and processes user inputs from the control panel (buttons/touchpad) so selections register and run.
• Drives the front display and indicator lights so temperature, mode and status information is visible.
• Replaces a failed or intermittent interface that causes unresponsive controls, blank or garbled display, or incorrect status indications.
• Works with the main control to pass commands; replacing the board can isolate interface-specific failures.

• Disconnect power to the appliance before starting — this part is electronic and may be damaged by live power.
• Take photos of existing wiring and mounting before removal to ensure correct reassembly.
• Handle the board by its edges and avoid static discharge; use anti-static precautions if available.
• Reconnect all plugs securely and test functions before fully reinstalling trim or covers.

This is a replacement dryer control board for an electric dryer. The dryer control board is the main electrical board that controls all the primary functions of a dryer. If the dryer has stopped working properly or is no longer turning or heating, this could mean that the dryer control board needs replaced. To replace the board, make sure the dryer is turned off and removed from power. The dryer control board will be located either on the back of the dryer or behind the user interface. Accessing it will require a screwdriver.This authentic OEM replacement part can be used in many models including the Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse and others.

Fix a dishwasher that won't start cycles, has display issues, or heating problems. This main control board manages timing and functions. DIY install.

If your oven won't heat, displays errors, or buttons don't respond, this electronic control board manages heating cycles and user interface functions.

If your washer shakes excessively or stops mid-cycle, the accelerometer sensor may be faulty. This part monitors vibration levels to regulate spin speed.

This electronic oven control replaces the console control used to operate a single-convection oven, restoring user inputs and cycle selection so you can reliably set temperature, timers and cooking modes. Ideal when display, touchpad or convection functions fail. What it does:

• Replaces the oven's main user control to allow selection of bake, broil, convection and timed functions
• Restores touchpad/button input and on-screen feedback when controls are unresponsive or blank
• Helps resolve symptoms such as no display, unresponsive buttons, or inability to start bake/convect cycles
• Interfaces with oven components to relay temperature and command signals to the heating system

• One control (single-conv) as shown

• Disconnect power at the circuit breaker before starting any work to avoid shock hazard
• Handle the control assembly carefully; avoid touching circuit board components and use anti-static precautions if available
• Installation typically requires removing the oven console or back access panel and unplugging the old control connector—refer to OEM service instructions

Fixes cycles running too fast or timer knob hard to turn. This electromechanical timer controls wash and spin cycle sequencing. Moderate DIY repair.

Oven won't heat to temperature or overheats dangerously? The electronic control board manages all oven functions. Moderate DIY repair, about 1 hour.

Fix oven lights that won't turn off, error codes E75/E35/F15, or non-responsive controls. This control board restores normal range operation.

Fix F11 error codes, blank displays, or non-responsive controls with this range electronic control board. Moderate DIY repair with basic tools.