Dispenser Switch Parts

Fix a burner that won't heat or has no temperature control by replacing this 6-inch element switch. Restores smooth low-to-high heat adjustment in 30 minutes.

Fix detergent not dispensing or leaking from your washer's drawer. This dispenser drawer assembly replaces cracked or warped drawers. Simple installation.

This is a factory switch used in the appliance's control/safety circuit. Replacing a worn or failed switch restores reliable signaling so the selected function engages properly and the unit responds consistently to user inputs and status conditions.

• Provides an electrical on/off signal to the control or safety circuit
• If faulty, selected functions may not activate or may be intermittent
• Can trigger error codes related to a switch input, depending on model

• Disconnect power before servicing; turn off gas/water if applicable
• Note/photograph wire locations and transfer connectors one at a time
• Verify actuator alignment and secure mounting before reassembly
• After installation, run a test cycle to confirm proper operation

This door switch detects whether the appliance door is open or closed. A working switch lets the machine start when the door is fully shut and stops operation when the door opens for safety.

• Monitors door position and allows the cycle to run only when closed
• Interrupts power to stop operation when the door opens
• Common symptoms of a failing switch: appliance won't start with the door closed, must press/hold the door to run, interior light stuck on/off, or a "door open" message on models with a display

• Disconnect power to the appliance before servicing
• Access the switch at the door opening/front panel; release mounting screws or locking tabs and remove the switch
• Move wires to the new switch one at a time to maintain correct positions
• After reassembly, test switch operation before running a cycle

Softener not dispensing or leaking? This washer dispenser assembly holds and releases fabric softener during rinse. Fixes clogs and cracks.

Fix dispenser door that won't latch or leaks at the door bottom. This grommet and latch kit stops water leaks. Requires inner door panel removal.

Detergent or softener not dispensing properly? This dispenser drawer assembly deposits detergent at the right time. Straightforward replacement.

This is a small electrical switch mounted near the dryer door opening that detects whether the door is open or closed. It completes the circuit that allows the dryer to run when the door is shut. Replace this switch if your dryer won't start, stops mid-cycle, or runs with the door open.

Fix a broken or missing dispenser drawer handle that makes it hard to open your washer's detergent compartment. Simple snap-in installation in minutes.

Fix an unresponsive control panel on your refrigerator. This touchpad registers button presses so temperature settings and features respond to your selections.

The fan control switch is the panel-mounted switch that sends power to the appliance's fan motor. Replacing a worn switch restores reliable on/off control and proper airflow so the fan starts and stops when it should.

• Provides user-operated on/off power to the fan/blower motor
• Helps regulate airflow for cooling, venting, or convection depending on model
• Typical symptoms: fan won't run, runs continuously, intermittent operation, or a loose/broken switch shaft
• Mounts behind the control panel and is actuated by the exterior knob/lever

• Disconnect power at the breaker before servicing
• Remove the control knob/actuator and panel trim to access the switch
• Note wire positions or take a photo; transfer wires one at a time to the new switch
• Secure with the original hardware, restore power, and test operation

Burner won't spark or ignite? This surface burner ignition switch triggers the spark module when you turn the knob. 45-minute DIY repair for ranges.

Fix unresponsive water or ice buttons, stuck dispenser, or blank display. This control board processes touchpad inputs. Easy 10-minute DIY repair.

This is a handle that attaches to the detergent dispenser drawer on a front-load washing machine. It provides a grip point for pulling the dispenser drawer open to add detergent, fabric softener, or bleach. Replace this handle if it is cracked, broken, or has snapped off, making it difficult to open the dispenser drawer.

Washer won't respond to cycle selections? This selector switch mounts behind the control knob to restore reliable setting changes. Easy DIY fix.

Replace worn or faded dispenser control labels that make settings hard to read. This overlay restores clear ice/water markings. Simple peel-and-stick fix.