Central Pack Small Engine Spark Plug Parts

This cap is a small protective cover used on select appliances to close off an opening or fastener. Replacing a damaged or missing cap helps keep out debris and moisture while restoring a clean, finished appearance.

• Covers an exposed opening or fastener to protect internal components
• Helps keep out dust, moisture, and spills
• Restores a clean, finished look and prevents snags
• Replace if the original cap is cracked, missing, discolored, or won't stay seated

• Disconnect power and, if applicable, shut off water or gas before service
• Remove the old cap by pulling straight off or unthreading, as designed
• Align the new cap and press or thread into place without forcing
• Verify a secure fit before restoring power and connections

Reversible door plug fills unused mounting holes when switching refrigerator door swing direction. Replaces broken or missing plugs for a finished look.

This replacement door latch engages the strike/catch to keep the door securely closed so the appliance can operate. A worn or broken latch can cause door-closed detection issues, doors that pop open, or cycles that won't start.

• Secures the door by engaging the strike/catch for a positive close
• Ensures door/interlock switches register "door closed" so the unit can run
• Helps maintain a reliable seal and reduces interruptions mid-cycle
• Common symptoms: door won't latch or pops open; appliance won't start; door/latch-related error messages

• Disconnect power to the appliance before servicing
• Note the latch orientation; transfer any original screws/clips as needed
• Align the latch with the strike and tighten fasteners securely
• Close and open the door several times to verify smooth engagement before testing operation

Reinforcement spacer maintains proper gap and support between panels, trim, or brackets. Replace if worn, missing, or cracked to restore alignment.

Dispenser won't open during wash cycle? This detergent dispenser restores reliable soap release and rinse-aid dosing. Moderate DIY repair with video.

Dispenser door won't latch or stay closed? This detergent dispenser assembly restores proper soap release. Moderate DIY—requires door panel removal.

Fix dispenser door that won't latch or leaks at the door bottom. This grommet and latch kit stops water leaks. Requires inner door panel removal.

Protective cover that sits over your dishwasher's pump inlet to screen debris. Replace if cracked, broken, or missing to protect internal components.

Fix a detergent dispenser door that won't close or latch properly. This assembly restores proper soap release timing. DIY repair in 20-30 minutes.

Wax motor for detergent/rinse-aid dispenser.

Maintains proper gap between range components for secure mounting. Replace if worn, missing, or cracked to prevent panel rubbing and ensure correct alignment.

Detergent not dispensing during wash cycle? This actuator arm with spring releases the detergent cup at the right time. Moderate DIY repair.

Rear pump housing for the washer drain/pump assembly. Replaces the worn rear housing that supports the impeller and bearing, helping restore proper draining and reduce leaks or unusual pump noises when the housing fails. What it does:

• Houses and supports the pump impeller and bearing, forming the rear half of the drain pump assembly.
• Restores a sealed mounting surface to help prevent water leaks from the pump area.
• Helps re-establish correct water flow and draining when a cracked or worn housing impairs the pump.
• Addresses symptoms such as poor or no draining, water at the base of the appliance, or loud/grinding pump noises.

• Disconnect power and shut off water supply before starting; drain any standing water to avoid spills.
• Remove the washer access panels and pump assembly; transfer the impeller, seals, and any hardware as required.
• Inspect and replace pump gaskets/seals and the impeller if worn; tighten mounting fasteners to OEM torque where specified.

Plastic cap that snaps over refrigerator door handle ends to cover mounting screws and finish the handle. Replaces lost, cracked, or broken caps.

For single drain outlet models only. For dual outlet port models you must order the complete pump and motor WD26X10013.

This dispenser is the door-mounted assembly that delivers ice and/or water from the refrigerator. It replaces a worn, cracked, or malfunctioning dispenser to restore normal dispensing and stop leaks. What it does:

• Provides a finished dispenser opening and support for the actuator and chute so water and ice flow correctly.
• Stops leaks and prevents food or debris from entering the dispenser area when cracked or damaged.
• Restores proper activation when the dispenser lever or paddle no longer engages the valve or auger.
• Helps eliminate jams or misalignment that can cause intermittent dispensing or noisy operation.

• Disconnect power and shut off the water supply before starting any work.
• Remove the inner door panel or trim to access the dispenser mounting screws and wiring.
• Handle gently to avoid cracking surrounding trim; test operation before reassembling the door.