Control Panel Lcd Parts

I first checked the power , we had 220 volt at plug, I removed the back of the stove, checked things out , I found that the stove top burners still worked and the oven light worked. I tested and found that we had current to the timer and clock but nothing on the control worked to set the time, or to turn the oven on or to set the oven temp. I ordered this part on June 30th and received the next morning. I disconnected stove from electrical plug. Be Sure to unplug the stove for your... Read more

• Fridge too cold
• Fridge runs too long

I went on you tube to try and figure out what might be causing this problem. It seemed that the problem was either the temperature thermostat or the defrost timer. I figured that seeing as I had never ever seen any frost in the freezer that the problem probably wasn't the defrost timer. So I ordered the temperature control thermostat, received it the very next day and in ten minutes removed the old one and installed the new one and we were good to go. It's been working just fine for the last... Read more

The replacement from AppliancePartsPros was a perfect match at a good price. The site also provided enough information to be pretty certain the timer was the source of our problem. Once I swapped out the timer the dryer ran perfectly again. The job was very easy except for 1 problem. The timer is mounted to the control panel using 2 pinch/spring clips, 1 above and 1 below. The above clip was easy to compress and release using either standard pliers or needle nose pliers. But the below... Read more

• Won't start
• Fridge runs too long
• Frost buildup
• Fridge too warm

After reviewing a number of testimonials and your videos from your APP.com site I determined my most likely problem was either the defrost heater, thermostat, timer or possibly all three. The real challenge now began. Getting to the specific parts with my specific model number was a real challenge. It was not as easy as removing the light guard and 5 screws since my model had two Track Cant Shelf vertical rails restricting the removal of the back panel. Also, these rails could not be removed... Read more

Given all the symptoms, we figured that the control board went out. First, unplug the refrigerator. The control board was easy to access by removing a panel on the back of the fridge. I unplugged all the connectors and used a putty knife to release the board from the plastic retaining clips. There was some browning on the underside of the board and the back of the refrigerator that suggests one of the capacitors on the board blew. Install the new board by pressing it into the retaining clips... Read more

GE Dishwasher would beep intermittently over the course of about a month. It then began to shut itself off. I would have to reset the breaker to get it to come on. Eventually, it stopped working altogether. After confirming that I did in fact have proper power to the appliance. The main control board had power and was in good shape. I then traced the problem to being a bad UI board. Which I found with the help of a nice lady over the phone at AppliancePartsPros.com. Read more

Just removed from front and the console. I wound up replacing the control board because the technician that I had come out said that's what was wrong and it would cost $250 to fix. I replaced the control board and it didn't fix the problem. After doing more research and searching out the error codes, I discovered I had to replace the console. so i did. I was able to return this control board and buy the console. That return policy was fantastic. I was so worried I was going to have to eat the... Read more

Main Control Assembly Read more

We turned off the circuit breaker. We then removed the light cover and then the control panel. We disconnected the Keyboard, Utah, plugged in the new one and turned the breaker on to see if everything worked. We realized that we did not need a new jazz board so that is being returned. The old Keyboard was removed, the new one attached and all the parts were put back. The frig works fine now at the recommended settings of zero and 38F. Read more

My Advantium worked fine except the clock and cooking instructions were dim and bounced in a circular pattern over the left side of the display. I tried unplugging it and once or twice that seemed to help. When I finally decided to take the control panel off I had a difficult time until I saw an old remark from a 2009 forum discussion from a guy that said there were about a dozen screws to remove to get to the control panel. That meant the entire cover had to come off! Wow! Glad I didn't break... Read more

Unplugged stove. Removed six 1/4 inch socket head screws from back panel. Removed back panel. Removed plug on the back of the OCB. Removed OCB. Used Philips screwdriver to remove four mounting screws (and cracked pieces of the mounting holes). If you can get to this point, installing the new OCB is pretty self explanatory. Read more

Had to remove the door from the main body of the dishwasher and then take the outer door apart from the inner door. Find a good video that showed how to do this but it was not exactly like the model of GE dishwasher that I have. Once you know how to remove the panel it went fairly quick. But in removing the inner door I broke the one end of Attach Strip Rh so I order a new one plus in taking the Graphics Asm apart to get to the UI board the small tab that holds everything together broke off. So... Read more

I went to appliancepartspro.com and found out that the problem could be the main circuit board. I went on and ordered the part, knowing it could be returned if necessary, but it was like music to my ears when I installed the part, myself, and turned the power back on. Easy. Thanks appliancepartspro. Read more

I located the web site via the internet and contacted the 1-800 number. The service rep was incredibly helpful and personable. After providing her with the model number and parts needed,the process could not have been easier. My replacement parts arrived the next day a perfect match. I highly recommend using this service, first class all the way. Read more

The circuit board under the machine needed replacing. Pretty easy if you are willing to not force it in. Two screws, four all different plugs, two guide holes for the wiring. I bought a latch but did not need to install it. Read more

My husband took the panel off. Check different things. Talked to someone at Appliance Parts. He told him some things to test. It was the timer that needed replacing. So happy to have my dryer working again! :) Read more