Nut Damper Control Refrigator Parts

Replaced the damper control. It took only 10-15 minutes. Since replacement, the clicking noise has stopped. Very happy with the result. However, want to share that there was probably nothing wrong with the original damper other than the original faulty design. The flap opens and closes and believe the clicking noise was the result of plastic against plastic. Noticed the new damper control is exactly the same as the original except that one of the flap sides now has a thick piece of rubbery... Read more

GE Dishwasher would beep intermittently over the course of about a month. It then began to shut itself off. I would have to reset the breaker to get it to come on. Eventually, it stopped working altogether. After confirming that I did in fact have proper power to the appliance. The main control board had power and was in good shape. I then traced the problem to being a bad UI board. Which I found with the help of a nice lady over the phone at AppliancePartsPros.com. Read more

• Won't start
• Fridge runs too long
• Frost buildup
• Fridge too warm

After reviewing a number of testimonials and your videos from your APP.com site I determined my most likely problem was either the defrost heater, thermostat, timer or possibly all three. The real challenge now began. Getting to the specific parts with my specific model number was a real challenge. It was not as easy as removing the light guard and 5 screws since my model had two Track Cant Shelf vertical rails restricting the removal of the back panel. Also, these rails could not be removed... Read more

Just removed from front and the console. I wound up replacing the control board because the technician that I had come out said that's what was wrong and it would cost $250 to fix. I replaced the control board and it didn't fix the problem. After doing more research and searching out the error codes, I discovered I had to replace the console. so i did. I was able to return this control board and buy the console. That return policy was fantastic. I was so worried I was going to have to eat the... Read more

The bar retainers just snapped in and the door handle can be replaced with three screws. Took about 5 minutes total. Read more

My Advantium worked fine except the clock and cooking instructions were dim and bounced in a circular pattern over the left side of the display. I tried unplugging it and once or twice that seemed to help. When I finally decided to take the control panel off I had a difficult time until I saw an old remark from a 2009 forum discussion from a guy that said there were about a dozen screws to remove to get to the control panel. That meant the entire cover had to come off! Wow! Glad I didn't break... Read more

Given all the symptoms, we figured that the control board went out. First, unplug the refrigerator. The control board was easy to access by removing a panel on the back of the fridge. I unplugged all the connectors and used a putty knife to release the board from the plastic retaining clips. There was some browning on the underside of the board and the back of the refrigerator that suggests one of the capacitors on the board blew. Install the new board by pressing it into the retaining clips... Read more

Removing the bottom panel and watching the internals while the washer was running revealed a small drip from what appeared to be a plastic cam that was attached to a solenoid. The water was dripping from the shaft the cam attached to down into the solenoid. Being a DIY guy I pulled the washer out, turned it upside down and inspected the effected mechanism. It appeared that there was a seal on the shaft that was leaking. The water leaking into the solenoid caused it to rust and stick. A quick... Read more

The circuit board under the machine needed replacing. Pretty easy if you are willing to not force it in. Two screws, four all different plugs, two guide holes for the wiring. I bought a latch but did not need to install it. Read more

I went to appliancepartspro.com and found out that the problem could be the main circuit board. I went on and ordered the part, knowing it could be returned if necessary, but it was like music to my ears when I installed the part, myself, and turned the power back on. Easy. Thanks appliancepartspro. Read more

Timer shaft rounded out! This pice of timer should not be plastic. Read more

My husband took the panel off. Check different things. Talked to someone at Appliance Parts. He told him some things to test. It was the timer that needed replacing. So happy to have my dryer working again! :) Read more

I replaced the control. Read more

Easy as removing s few screws and switching out two plugs. Read more

Exchange one MB with another MB. Just had to plug colored wires into the proper color code. Read more

The part fit exactly like the old existing one. Read more