Power Strike Small Engine Start Switch Parts

• Lid or door will not open
• Won't start
• Lid or door won't close

Just removed the old and put on the new,simple.On this Fridgidare washer you should lift the door as you close it which should make the striker last.. Read more

After reading the reviews of others, I ordered and replaced the heating element, thermostat, cut-off & the moisture sensor bars. It was a success! The element was definitely bad on one end, the wire was burnt in two pieces. Now it doesn't take 3 hours to dry a load! Well worth the money I spent. Easy to fix & do it yourself. I watched the video before buying the parts just to make sure that it was something I wanted to tackle. Very easy with the video. Great job Appliance Pro's! Read more

• Too hot
• No heat or not enough heat

The heating element had a break in the heater coils, so I replaced it with a new one from Appliance Parts Pros. I also replaced the thermal fusible link and thermostat switch because they were so cheap it just made sense to go ahead and do it while I was in there. I also cleaned every nook & cranny in the dryer, then cleaned out the vent piping- which was about 100% clogged. The video's of how to tear down a dryer were indispensable to this repair - along with APP's always having the right... Read more

• Door won't close

There is a video on youtube that talks about how to disassemble the electronic component out of the control board so I really won't go into that part of it. This disassembly of the control board will need to take place before you can even get started taking the gray piece out of the console to replace it. Be careful not break off the little tips behind the control knob, don't force it, it does come apart easily and there is an easy way to do it, that is also on youtube. This is where the... Read more

Unscrewed the stove top, unplugged the connections, removed the stovetop. Replaced the burner and the switch. Put it back together again. Read more

First ran the built-in diagnostic tests. Got error code indicating that the inlet thermistor was open. Removed lower access panel and did continuity checks on the inlet thermistor, thermal cutoff and heating element. Even doing these checks is very difficult on this model due to the location of these parts and the limited access through the so-called access panel. But was able to get an open reading on the heating element, so I knew that at least that part was faulty. Could not get a reliable... Read more

We ordered a door switch, dryer latch and strike plate. We realized that we only needed to replace the door switch. We watched a few videos and then replaced the switch. We couldn’t find a video for our model but they did give us a pretty good idea about what we needed to do. The hardest part was getting the original door switch out, all of the videos we watched showed us that it would pop out with a little pressure from a flat head screw driver, from the front of the switch. We could not get... Read more

You can do this! Although an Art Director by trade, I like working with my hands. I’m adept at working with tools and following instructions. In today’s disposable society, I prefer fixing things. That said, this has to be the easiest repair I’ve ever attempted with the largest cost-savings versus hiring a professional. My brand new dryer had been in use fewer than six months (average 6 loads per week) when suddenly the dryer would not heat. The drum would spin, there were no error codes, and... Read more

• Element will not heat

Replaced all four element switches. Switches arrived within two days of ordering. That's about normal for AppliancePartsPros. They were the correct ones; not generic, and fit the original control knobs perfectly. This kind of service is what I'm used to from ApplicanePartsPros. Read more

• Door won't close
• Door stuck closed

This was much easier than expected. I called Appliance Parts Pros with my model # and you told me what part I needed. It was shipped the same day and arrived the next day. I removed the inner door trim with a table knife ( don't rush this or you might crack the trim ). I then unhooked the old door latch disconnected the spring from the door hooked on the spring from the new latch and clipped in the latch to the door. Final step was to reattach the door trim. It was very easy and all I used... Read more

The part is so new no video so I went onto a similar part and watched video that got me about 80%. Then, called and customer service sent me a service Manual but this still was not specific so I broke the old to get it out and in the process figured out how to do it correctly. So I installed the last bit of it which was the bezel through the machine top by myself correctly. So you take the old one out by pushing out to the right from the bottom side using a screw driver for leverage. It will... Read more

• Won't start
• Too warm
• Fridge too warm
• Freezer section too warm

In short - I replaced the evaporator fan motor and the evaporator fan blade. The Appliance Parts Pros website was extremely helpful to me. Here's how. 1. The site helped me identify that even though my Freezer says it's a Frigidaire, it's actually an Electrolux. 2. The site identified the potential screech causing parts. (I didn't take a chance, I bought all three) It was a worthwhile investment. My freezer is 20 years old so it deserved some help. 3. The site provided guidance videos (not... Read more

I ran a diagnostics check on the washing machine and came up with the error code E47 -Board thinks the door PTC circuit is open in spin. The washer thought the door was open and would not finish the spin. I was left with a washer full of very wet clothes. This repair was SO extremely easy. I only needed to uses a pair of needle nose pliers and a screw driver. It took less than 10 minutes, start to finish. Now the new door lock assembly registers correctly and my clothes are completely... Read more

Watched a You Tube video on how to remove the bad lid lock, ordered a new part and installed. Read more

• Doesn't shut off
• No heat
• Won't start

The first symptom was our microwave would continue to run after the time was up. The light would go out, the turn table would stop but you could still hear the microwave running and whatever was in it would continue to cook. The only way to stop it was to open the door. It was intermittent at first but eventually it would always run no matter what as long as the door was closed. Several other posts referenced these switches as the problem. I just replaced both and problem gone. It turns out... Read more

Replaced it. Read more