Power Small Engine Safety Switch Parts

• Element will not heat

1. Went online where I watched video about heat control for this Maytag. I then found AppliancePartsPros using Google. I ordered the part and In three days the part arrived. I installed the part and now the problem has been corrected. Read more

I tried to buy a new refigerator, but strangely none of the major stores had anything I wanted in stock. The earliest delivery date for a new unit was over a month away. At that I decided to try and keep this one running. I did online research into common refigerator problems. I found the cooling coils in the freezer were covered in a block of ice and frost. The refigerator was not going through a defrost cycle. With a hair dryer I thawed out the coils. The refigerator worked fine for... Read more

• Too hot
• Shuts off too soon

I posted the following on the Facebook page ; SOoooo my 10 year old clothes dryer stopped and like almost everyone else I just figured it's shot, burned up, gotta get a new one. Well, due to a few bumps in the road I cannot afford another problem. My 2 vehicles are not running and with one being in the shop for 3 weeks and not being able to afford a rental car anymore this dryer was another headache. It sat for weeks and laundry started piling up. While looking online for sales somehow I... Read more

• No heat or not enough heat

Changed out high limit thernasstat Read more

I replaced the energy regulator. Read more

Replaced control board. Did not need Control Thermistor in my case, but I'm keeping it as backup. Got the Drum Belt just in case it breaks on me since the dryer is aging. To replace control board: Disconnect power and pull dryer away from wall. Take 2 black screws on the back off to remove the top lid. Remove 2 screws on top that hold the control interface on. Remove 2 screws on the bottom backside of the control. Pull out control panel and pull off terminal connections and push to remove... Read more

After disconnecting power to the fridge, I first removed the ice maker/water dispenser/fridge control faceplate. This easily popped out using a flat head screw driver. Then disconnected the 3 wire harness connections to the control board. I next removed the plastic dispenser housing shield. There's only 4 screws that hold this on. Finally, I removed the Micro-switch, disconnected the two wire connectors and installed the replacement switch and reinstalled everything. The repair took only... Read more

• Too hot
• No heat or not enough heat
• Shuts off too soon
• Takes too long to dry

This Maytag dryer was bought in 1985 if memory serves. It has worked hard with few repairs done by yours truly over the years. Thanks to the engineering and excellent design by Maytag staff, removing parts are relatively easy. Once I opened the unit, I found it to be full of lint. I cleaned the entire inside and the vent pipe duct work. I found the blower wheel assembly worn. Though it was not cause of my problem, I decided to change it along with the igniter, heater relay and the fan belt. I... Read more

Replaced switch! Easy.... Read more

I replaced all 3 remaining burner controls because they were all original (mid 1970s GE electric range w/coil burners), and one of the controls occasionally made arcing sounds when cycling the burner on and off. If a control is making odd noises - more than just a quiet metallic clicking as it cycles - it should be replaced. I'm assuming you have experience with the tools needed and can do simple mechanical assembly or disassembly, but have not previously worked with electrical equipment of... Read more

After checking other reviews, we decided it was best to replace the interlocks, cam and all three switches. You're going to need a phillips screwdriver, star driver, small screwdriver and needle nose pliers. You need to remove the ONE Phillips screw above the control panel inside the vent. The contol panel is on hinges that you can slide up and towards you. Using caution remove the wires noting how they're connected. Pinch the top of the white connectors and wiggle them free. We couldn't get... Read more

After removing the top rear access panel, I took as-built photographs of the two components to be replaced showing all wires, connectors and screws! The Energy Regulator for the front left burner was replaced first, noting the orientation before pulling off the knob, and removing the retaining screws. I used long nose pliers to gently remove one lead at a time and reconnect to the new regulator. Checked orientation against the photo, reinstalled regulator and knob. Main PCB Assembly was... Read more

I got on the site and shared my issue. It was determined my door switches were bad, as well as my actuator. I ordered the parts (which arrived in just 2 days!) and I fixed it myself in just under 10 minutes, for under $30.00. Thanks guys!!!! Read more

• Light not working

We had delayed repairing the problem because we received a price of more than $ 100 from a local appliance repairman. However, after viewing the view on the ApplianceParts Pro website, I saw what an easy repair it would be. After receiving the part from you, I had my son do the repair because I felt it would a good father - son bonding time. It was so easy and he was proud of his ability. Thanks for your excellent repair video and the excellent price. It costs less than $ 22 instead of more... Read more

Check fan operation and was OK. Everything else worked except when microwave was started for a cycle. I looked around on internet and found someone had trouble with the door switches. I started to check door switches and found one shorted. I replaced both lower door switches and it took care of problem. Read more

Replaced the switches. Read more