Roller Nut Parts

I ordered the parts and replaced them with new ones. Read more

• Touchpad does not respond

Most of the instructions you find online are for a different type of coupler that pops off. This model is different, as the coupler unscrews. I found a video for this specific model blender and I'll summarize below: Turn the blender over so the bottom of the blender is facing up You have to pop the bottom rubber feet off. Take off the four screws on the bottom of the blender Lift the bottom of the blender up and off. This may take two people. You'll need a heavy duty wrench under... Read more

I was getting really frustrated with our oven. It would preheat to the correct temperature, then slowly lose heat until it was down to about 200 degrees. So it took about two hours to heat a pizza! Finally decided to repair the oven myself, rather than pay $300.00 to have a repair person come out. Ordered the replacement igniter from AppliancePartsPros.com, and it arrived in two days. I followed the instructional video on the AppliancePartsPros.com website, and it was going well until I... Read more

I found my parts and ordered the six I needed, however I did not pick up on the difference from the front wheels to the rear wheels in the the descriptions. The rear wheels are narrower and I ordered all front wheels, six fronts instead of four front and two rear. I made it work by using the axle from the new wheel with two old narrow wheels. Read more

Replaced rollers which were easy except i had to pull the dishwasher about half way out of the cabinet Read more

I looked for a site that sold replacement parts for my make of GE refrigerator. I found AppliancePartsPros, and was very surprised at how organized it was. By entering the model number of my refrigerator, I was shown a set of (approximately) 8 general parts diagrams for my refrigerator. I chose the ice making/dispensing diagram. I matched the part that shattered (from use) to what was on the diagram. What I didn't know was how to install the part. I saw references by other customer comments to... Read more

I have a large Samsung 4 door refrigerator. One of the rear wheels broke. To replace it, you need the wheel and the shaft. To lift the refrigerator for the repair, I had my wife stand in front of it with her foot on a board that was wedged against the front wheels. I then pushed the refrigerator up from behind and slid a 3/4" piece of plywood underneath the bottom with my foot. This gives you enough space to do the repair. After removing the back cover, it's best just to knock out the broken... Read more

Ordered new wheel assembly, which came in about a day and a half. The broken assembly was on the left front so I only had to slide the dishwasher out just enough to expose the two mounting screws on the outside of machine.When you remove the old assm there are two rubber washers on the back side. If you didn't order new ones,remember to remove them from broken assembly and install them onto the new piece.Overall this is an easy fix and took about ten minutes including pulling the machine away... Read more

Ordered new freezer arm Read more

It took a little longer then I was hoping but wasn’t terrible. If the burner is very old at all make sure to get the new screws. Both of mine snapped when trying to remove them. The new one works great. Read more

Replace idler wheel assembly, belt and spring. Read more

Tipped the dishwasher on to its front, loosened the drain hose clamp and pulled the hose off. Then unscrew the fill hose which looks like a garden hose adapter. Cut the zip tie on the drain hose and take note of how both hoses are routed, then pull both hoses out the back of the dishwasher. Insert new hoses and route them correctly and hook everything back up. Couple of notes, I didn't have to take off the outer cabinet to do this repair. Get plenty of towels because a lot of water can get... Read more

No problem, 1 min to fix Read more

Replaced it. Read more

Bot both sets of roller bearings, lower ones on the appliance and the set on the trash can that rolls out. I just followed the instructions that were in the roller bearing package and only needed the tools that are recommended. Was a little tricky with the nuts, really need a person with "small" fingers to reassemble the nuts back on the lower set of bearing that are on the appliance. All in All, went well and works. Found that the new bearings are v. tight on the machine, being new, so, use... Read more

Replaced the right and left front upper dish rack wheels. The best part was I ordered the parts Monday and had them first thing Tuesday morning. Read more