Need Help?
Call
Range burner won't shut off or heat properly? The infinite switch controls burner temperature. DIY-friendly repair takes about 15-20 minutes.
I ordered the infinite switch control from Appliance Parts Pro on a Wednesday afternoon and it arrived well packaged the next day even though I selected standard shipping. Thank you for the easy ordering and fast delivery! Replacing the old switch was easy: 1. Disconnect the power to the stove 2. Make sure the power is off to the stove 3. Pull 4 burner control knobs off and remove 4 large nuts attached to the 4 burner switches 4. Lift the face plate off and clean previously hidden cooking... Read more
Downdraft fan not working? This fan switch activates the ventilation system. Moderately difficult repair—requires lifting cooktop to access mounting plate.
I had to take the control board off the bottom of the cooktop and replace the fan switch. The post that fits into the hand switch had broken off. The new switch cost about $35, it was an exact replacement and the whole repair took less than an hour. My wife is very happy because now she can again use the downdraft fan on the cooktop. Thank you AppliancePartsPros. Read more
Burner won't shut off or stays on high? The infinite control switch regulates surface burner heat. Easy DIY repair, typically 10-15 minutes to replace.
Replaced the large burner control switches for the ones giving trouble. Since the other two switches had seen as much use as the faulty ones, replaced them too. After putting in new switches, found that one large burner had burned out so replaced it also. Range now cooks as good as new Read more
Fix a washer that overfills or won't start the wash cycle. This water level pressure switch detects proper fill levels. DIY-friendly repair.
Hmm...watched video after reading on web of running water problem with GE washer....common fail .....moving stuff to get to the washer took all the time, easy fix but a lot of screws to remove and looking time APP site very good, will order again if need be thanks Read more
The Flood Switch is an OEM part for GE dishwashers. This critical component detects and prevents potential overflows by monitoring water levels within the dishwasher. When excessive water is detected, the flood switch signals the dishwasher to shut off water flow, preventing leaks and potential water damage.
Causes of a bad flood switch can include electrical failures, physical damage from debris, or wear and tear from repeated use. If the flood switch malfunctions, it may not properly detect water levels, leading to possible overflows or improper operation of the dishwasher.
Symptoms of a bad flood switch include:
This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.
Spoke to an appliance repairman who said it does not pay to fix and is too difficult I had already ordered the parts. So I called AppliancePartsPros.com. They said no problem if I wanted to return parts BUT the technician suggested that all appliances are repairable I gave it a shot I had to disconnect the dishwasher, same as if I was to replace it Followed on AppliancePartsPros.com repair parts video and replaced the pump, inlet valve, and solenoid all took about an hour and the dishwasher... Read more
Washer won't start or keeps blowing fuses? The lid check switch ensures your washer only runs when the lid is closed. Easy DIY repair in under 30 minutes.
First I needed to replaced the timer. However that timer is no longer available. So I was not able to buy that part. A friend encouraged me to cross reference the part number. I did and I found another timer that claimed it would work on my machine. It looked very similar. I got the timer from you guys and put it in. The water valves worked right away but the motor did not. I researched more troubleshooting ideas and discovered I had a bad lid check switch. I got a new one of those from you... Read more
This is a micro switch that detects whether the microwave door is properly closed and latched. It is part of the safety interlock system that prevents the microwave from operating with the door open. Replace this switch if the microwave does not start when the door is shut, runs with the door open, blows a fuse when the door closes, or stops mid-cycle intermittently.
Knowing the odds of 2 failures occurring at the same exact time was unusually high, I just searched your site for what other broken items might affect these two failures. Came up with next control item upstream and tallied that item failure with percentages of successful repairs, (4 mins.) door safety switch. Since I had to change out the most likely of the 3 and since I was already was going to be into the switch panel I ordered all 3 and swapped them all out to cover my butt, as they were... Read more
Burner won't turn off or stays on high? This range surface element switch controls heat output. Easy DIY repair—most install in 5-10 minutes.
Installed new switches. Done in 20 minutes. Read more
Burner stuck on high or won't heat? This infinite switch controls cooktop element temperature. Common DIY repair taking 30-60 minutes with basic tools.
Had to replace the switch for the left rear burner on a Whirlpool cooktop Model W5CE3625AB00. I turned off the circuit breaker for the cooktop and lifted it out of the countertop. It was simply held down by its own weight. There were approximately a dozen screws holding the smooth surface down onto the rest of the unit. I removed those screws, which allowed the cooking surface to lift back on a hinge in the back of the unit. Two of those screws were stripped, but I was able to remove them... Read more
If your dual burner only works on high or won't heat at all, this dual infinite switch kit restores full temperature control. Moderate difficulty install.
Replace dual infinity switch. The only difficulty is the terminal labels on the new switch did not match at all with the terminal labels on the original switch. The enclosed instructions were NOT helpful. But I contacted your representative, Johnny, and he was most helpful and patient. From my model number he located very specific and detailed instructions for how to wire the new switch. The rest of the job was easy. Your representative was outstanding. Thanks. Read more
Burner stuck on high or won't turn off? This burner control switch regulates heat settings. Moderate DIY repair—label wires before swapping.
If one control starts to fail the rest are sure to follow soon - so I replaced all four on our JennAir S160. Looked up the parts on line. Due to my background as an aviation electrician in the Navy and then working as an electrical systems designer for a defense contractor the toughest part was the clean up. Oh Well. Read more
If your dual burner stays on low and won't turn off, or the small element doesn't heat, this infinite switch may need replacing. DIY-friendly repair.
Replaced the infinite, dual, switch. Very good instructional video for Safety, removal * install. Read more
Dishwasher won't fill or keeps overfilling? The float switch detects water levels for proper filling and draining. Accessible repair in under 30 minutes.
I checked continuity at the float switch since I knew the inlet valve was working when direct wired to 120v. Switch did not have continuity. Replaced switch and inlet valve worked at start of cycle. Read more
The Start Switch is an OEM replacement part for Whirlpool dryers. It is an electronic component responsible for initiating the heating elements and tumble cycles upon user command from the control panel.
Causes of a bad start switch involve general wear over extended use. Failure of the internal conducting surfaces interrupts circuit activation as well.
Symptoms of a bad start switch include:
Note: This dryer push-to-start switch has 2 terminals.
This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore electric dryer models.
I replaced the starter switch, that really didn't need to be replaced, and the thermal fuse, which did. Read more
Fix a washer that won't fill, overfills, or shows E35 error code with this water level pressure switch. Moderate DIY repair takes about 1-2 hours.
Water valve not closing all the way. Water keep entering washer even with power cord unplugged. Parts I ordered fit perfect. Ordered on Thursday night , parts there Saturday. Great service and shipping. Thank Read more
Burner not heating or stuck on? This surface element switch controls power to your cooktop burners. Common repair when heat won't adjust properly.
Replaced the switch infin by watching the video Read more
By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.