Actuator Ptc Parts

This replacement switch restores reliable on/off signaling to the circuit it controls, helping your appliance start, stop, and respond correctly. A worn switch can cause intermittent operation, no response, or lights and functions that don't activate. What it does:

• Provides an electrical open/closed signal to enable functions like starting a cycle, powering a motor or light, or shutting a feature off
• Acts as a safety/position interlock (such as door, lid, float, or hood) depending on the model
• Typical symptoms include won't start, won't stop, light won't turn on/off, or intermittent operation
• Can be checked with a multimeter for continuity when actuated

• 1 switch

• Disconnect power before servicing; turn off gas or water supply if applicable
• Access the switch, note wire locations, and transfer leads one at a time to the new switch
• Mount securely, ensure the actuator aligns and wires aren't pinched
• Reassemble and test operation before finalizing

Replacement actuator pad for refrigerator water and ice dispensers. Snaps into dispenser panel. Replace if cracked, broken, or tabs are damaged.

Washer won't spin or door won't lock? This door lock spin enable switch signals the control to start high-speed spin. Moderate DIY repair, 30-60 minutes.

Supplies electrical power from wall outlet to refrigerator. Replace this cord if cut, frayed, overheated, or damaged to restore safe electrical connection.

Replacement actuator arms for refrigerator ice and water dispensers. Includes both paddles. Needed when arms are broken, cracked, or missing.

The Switch is an OEM component specifically designed for Frigidaire washing machines. It controls various cycle options like water temperature levels, spin speeds, and additional settings like stain removal cycles.

Causes of a bad switch can include water or chemical damage leading to component failure over time, or loose wiring connections causing intermittent issues.  

Symptoms of a bad switch include: 

• Inability to select wash cycles or adjust settings  
• Unresponsive or inaccurate temperature levels
• Lights/displays not functioning as normal
• Error codes indicating switch problems

This OEM Frigidaire replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models. Replace yours today to avoid expensive repairs down the road.
 

Dryer won't heat or overheating? The temperature switch controls heat settings. DIY-friendly repair—just swap wires and reassemble. Takes 20 minutes.

This is the washer's water level switch that senses tub level via air pressure and provides five selectable fill settings. Replacing a failed switch restores accurate filling and lets the cycle advance properly through wash, rinse, and spin.

• Monitors air pressure from the tub to detect actual water level
• Controls the inlet valves to start/stop filling at the selected setting
• Signals the timer/control to begin agitation and advance the cycle once full
• Common symptoms: overfilling or water keeps running, stops filling too soon or won't fill, inconsistent water levels, cycle won't advance due to incorrect level detection

• Disconnect power and turn off water supply before servicing
• Access the control console; remove the selector knob/dial and panel as needed
• Note wire locations (take a photo), move the harness, and transfer the pressure hose; ensure the hose is clear and firmly seated
• Securely mount the new switch, reassemble the console/knob, restore utilities, and test each fill level

Fix compressor clicking every few minutes or fridge not cooling. This start relay and overload combo helps your compressor start and prevents overheating. Easy 5-minute fix.

This hinge lever mounts on the refrigerator door hinge to guide door movement and closure, helping the door seal properly. Replacing a worn or broken lever restores smooth operation and consistent sealing.

• Guides hinge motion so the door opens and closes smoothly
• Helps maintain door alignment for a reliable gasket seal
• Replace if the lever is visibly cracked, worn, or deformed

• Disconnect power and support the door to prevent injury or damage
• Remove the hinge cover and fasteners; note the lever's orientation before removal
• Install the new lever in the same position and reassemble the hinge components
• Adjust hinge per model procedures if needed

Fix a compactor that won't start, stops mid-cycle, or requires holding the pedal down. This drawer tilt switch is a quick 15-second replacement.

Dryer won't heat or overheats on low settings? A faulty temperature selector switch prevents proper heat control. Easy DIY fix in 10-15 minutes.

Fix erratic or unresponsive cycle selections with this laundry center rotary encoder switch. Mounts behind the cycle knob to restore accurate settings.

Cup-activated lever that controls ice dispensing on side-by-side refrigerators. Replace if cracked, broken, or unresponsive to restore dispenser function.

This fixed-value resistor is an electrical component used in select dryers to limit current in a specific control circuit. It helps the timer or electronic control operate correctly by dropping voltage to safe, design-intended levels.

• Provides precise resistance to reduce voltage/current in the designated dryer circuit
• Supports proper operation of the timer, control board, or end-of-cycle signal (varies by model)
• Failure may present as a timer that won't advance, an inoperative signal/buzzer, or irregular cycle behavior
• Replace if visibly burned/damaged or if testing shows an open or shorted condition

• Disconnect power to the appliance before servicing
• Access the console/wiring harness and note original wire routing
• Make secure, insulated connections and route the resistor/leads exactly as original to avoid heat or chafing
• After installation, run a test cycle to ensure proper operation of the affected function

The Starter is an OEM replacement part for Frigidaire refrigerators. This component is crucial for initiating the compressor, which is responsible for cooling the refrigerator. The starter works by providing the necessary electrical power to get the compressor running, ensuring that the refrigerator maintains the correct temperature.

Causes of a bad starter can include electrical malfunctions, wear and tear over time, or damage from power surges. A faulty starter can prevent the compressor from starting, leading to cooling issues.

Symptoms of a bad Starter include:

• The refrigerator not cooling properly
• The compressor not running or frequently cycling on and off
• Unusual clicking or buzzing noises from the compressor area
• The refrigerator being warmer than usual or food spoiling quickly

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.