Assy-Case Sensor Parts

• No heat or not enough heat

GE Gas Dryer Model DBVH512GF1WW began to heat for only a short amount of time so drying clothes took WAY too long. Read online that the first thing to replace are the solenoids. Bought the two solenoids from AppliancePartsPros.com for about $50 total, and it seems to have fixed the problem. Had to watch a few videos to learn to disassemble the dryer, and the job took a couple of hours, but now that I know what I'm doing it could be done in less than 30 minutes. Also, the old solenoids tested... Read more

Replaced thermostat. Read more

Tested the old t-stat with ohm meter. When shaken, the contacts would open. Replaced it with new t-stat and it works fine now. Thanks! Read more

My Electrolux Frigidaire Gas Dryer stopped working and I got an error code E66 that the thermal limiter blew from over heating. The E66 code stops displaying after the initial code and you will then get a door open message. I replaced the thermal limiter and the thermostat just to be sure which part at the problem. The job is hard because you have to take apart the entire dryer and remove the drum. Would be a tough project to complete on your own. Read more

This was a friends dryer. They'd been quoted a $200 call out fee and after taking with them on the phone were also told they could have the dryer taken away for $150. I told my friends that inwould fix it. I used a multimeter to check the thermostats, heaterbelement and funrion dial. I found 2 bad thermostats. I orderd one part from you, another from elsewhere as you did not have stock. I replaced the dead parts with new and the dryer heats again. It cost me $65 total in parts and shipping to... Read more

Removed exterior panels, cleaned all venting, replaced outlet thermistor and thermostat. Pressure washed all removable parts. Reassembled. Now working as it should. Read more

Replaced the thermst-fix and the thermal fuse oven now works great Read more

• Won't start
• No heat or not enough heat

Did some dryer repair research (dryer not heating) on the internet. Bought an ohm meter, opened up the dryer and tested the cut-off-T, high limit thermostat, dryer igniter, flame sensor, cycling thermostat for continuity. The igniter was bad, the other parts tested ok. Went online to AppliancePartsPros.com searched for a new igniter for my specific dryer model, found the right replacement igniter and watched the video on how to replace the igniter. Because my dryer is old (15+ years) and I... Read more

Replaced fuse. It took much longer to get the oven out of the wall to access the fuse and replace the front panel than to do the repair. This fuse failed at the end of the cleaning cycle for the bottom oven and left the door locked because the open fuse removed the 120v power from the control board. The locked door made it impossible to remove one of the screws holding the wall oven in place. However, after I ground off the head of the screw behind the edge of the locked door I was able to... Read more

Checked vent first to see if there was a blockage. Removed top, front and drum of dryer. Replaced all sensors including flame detection and gas valve coils. Re-assembled and tested. Dryer was now heating Read more

This fridge has had a problem of ice building up around evaporator coil in fresh food side. Wife (she HATES this thing) says it's done this from day one; 10 years. GE guy says all these models do this and there's no fix for it, so we have clean out the ice periodically... Like the 1940s pre auto defrost. Now with the issue of FF side temp too highi assumed the ice had built up around FF evaporator coil preventing proper cooling, but AppliancePartsPros.com suggested the FF temp thermistor may... Read more

Out with the old. In with the new. No problem. Dryers are simple and usually can be fixed quickly. appliance pros makes it easier with their tutorial videos and fast shipping! Read more

• Doesn't shut off

Looked online. Others said to start with the thermostat because its cheap and easy to fix, so I did. The thermostat is located at the rear of the oven on the back. You need to remove a total of 3 panels to get to it. Do not confuse it with the thermal sensor at the rear of the oven on top. My thermostat was clearly deformed, and I had never run a self clean like other with testify to. Simply replace it - easy. Oven worked like new. Read more

Fridge keept building up ice in defrost drain drain in freezer. Once the drain pan filled with ice it drips into fridge compartment. After taking things apart three times to thaw it out, decided to replace defrost components - heater and temperature switch. In addition to new parts, also added a 12 gauge copper wire hook that hangs from defrost heater into the defrost drain. After this, the defrost cycle is running as expected, but will not know if the issue is corrected until a year or so... Read more

So I replaced the hi-temp thermostat and the problem is fixed. Read more